Zum Hauptinhalt wechseln
Hilfe

Disassembling Insignia NS-B2110 Internal Components

This guide will show you how to disassemble the internal components of the Insignia NS-B2110. You may need this step as a prerequisite for other replacement guides.

  • Autor: Daniel Hodges
  • Geschätzte Zeit: 30 - 45 Minuten
  • Schwierigkeitsgrad: Moderat

Many of the important components of the stereo are located on the inside of the device. To get to these components, you must remove the internal components of the device.

Abschnitte
Werkzeuge

Schritt 1 Internal Components  ¶ 

With a Phillips #2 screwdriver, remove five 5mm screws from the "quarter circle" circuit board. More wires! Handle the circuit board carefully and take caution not to stretch the red and white wires connected the board to the other components.

Schritt 1 Internal Components  ¶ 

  • With a Phillips #2 screwdriver, remove five 5mm screws from the "quarter circle" circuit board.

  • More wires! Handle the circuit board carefully and take caution not to stretch the red and white wires connected the board to the other components.

  • Remove the green quarter circle circuit board and place to the side.

Schritt 2  ¶ 

On the brown side of the quarter circle circuit board, remove the two white ribbon cables with pink stripes attached to a plastic connector. To do this, pinch the tabs with your hands while pulling outward on the connector.

Schritt 2  ¶ 

  • On the brown side of the quarter circle circuit board, remove the two white ribbon cables with pink stripes attached to a plastic connector. To do this, pinch the tabs with your hands while pulling outward on the connector.

Schritt 3  ¶ 

With a Phillips #2 screwdriver, remove four 6mm screws from the rectangular circuit board.

Schritt 3  ¶ 

  • With a Phillips #2 screwdriver, remove four 6mm screws from the rectangular circuit board.

Schritt 4  ¶ 

Remove the two white ribbon cables attached to white plastic connectors from the circuit board by pinching the tabs with your hands and pulling outward on the connector.

Schritt 4  ¶ 

  • Remove the two white ribbon cables attached to white plastic connectors from the circuit board by pinching the tabs with your hands and pulling outward on the connector.

Schritt 5  ¶ 

Red and white wires are attached to this board as well. Once again, be careful not to stretch these.

Schritt 5  ¶ 

  • Red and white wires are attached to this board as well. Once again, be careful not to stretch these.

  • Remove the rectangular circuit board and place it to the side.

Schritt 6  ¶ 

With a Phillips #2 screwdriver, remove two 5mm screws from the black plastic frame which previously held up the rectangular circuit board.

Schritt 6  ¶ 

  • With a Phillips #2 screwdriver, remove two 5mm screws from the black plastic frame which previously held up the rectangular circuit board.

  • Remove the black plastic frame.

Schritt 7  ¶ 

With a Phillips #1 screwdriver, remove four 3mm screws from the silver metal circuit board. This board has two white ribbons attached to it. Once again, be careful not to stretch these.

Schritt 7  ¶ 

  • With a Phillips #1 screwdriver, remove four 3mm screws from the silver metal circuit board.

  • This board has two white ribbons attached to it. Once again, be careful not to stretch these.

  • Remove and place the metal circuit board to the side.

Schritt 8  ¶ 

With a Phillips #2 screwdriver, remove the two 3mm screws from the black plastic tuner frame.

Schritt 8  ¶ 

  • With a Phillips #2 screwdriver, remove the two 3mm screws from the black plastic tuner frame.