Zum Hauptinhalt wechseln
Hilfe

Squier Strat Guitar Teardown

Teardown

Teardown

Teardowns bieten einen Einblick in ein device und sollten nicht als Demontageanleitung verwendet werden.

Anleitung eines Mitglieds

Anleitung eines Mitglieds

Ein großartiges Mitglied unserer Community hat diese Anleitung erstellt. Sie wird nicht von iFixit Mitarbeitern überprüft.

Teardown of electric guitar

Schritt 1 Squier Strat Guitar Teardown  ¶ 

Pull off the three tone/volume caps.

Schritt 1 Squier Strat Guitar Teardown  ¶ 

  • Pull off the three tone/volume caps.

Schritt 2  ¶ 

Pull off the end cap on the pickup selector.

Schritt 2  ¶ 

  • Pull off the end cap on the pickup selector.

  • Note: This is not how the switch should normally look. This one is bent slightly; the tip should be pointing straight up.

Schritt 3  ¶ 

Unscrew the three bolts holding the tone/volume potentiometers to the scratch plate.

Schritt 3  ¶ 

  • Unscrew the three bolts holding the tone/volume potentiometers to the scratch plate.

Schritt 4  ¶ 

Remove the 3 washers from the tone/volume potentiometers

Schritt 4  ¶ 

  • Remove the 3 washers from the tone/volume potentiometers

Schritt 5  ¶ 

Unscrew the eight screws which hold the pick guard to the main body.

Schritt 5  ¶ 

  • Unscrew the eight screws which hold the pick guard to the main body.

Schritt 6  ¶ 

Unscrew the two screws holding the pickup selector in place.

Schritt 6  ¶ 

  • Unscrew the two screws holding the pickup selector in place.

Schritt 7  ¶ 

unscrew the six screws holding the three pickups in place.

Schritt 7  ¶ 

  • unscrew the six screws holding the three pickups in place.

Schritt 8  ¶ 

Lift off the scratch plate, revealing the electronics inside the main body Lift off the scratch plate, revealing the electronics inside the main body

Schritt 8  ¶ 

  • Lift off the scratch plate, revealing the electronics inside the main body

Schritt 9  ¶ 

Another method of dis-assembly: remove the pickguard screws (leaving pickup screws, pots and switch untouched).

Schritt 9  ¶ 

  • Another method of dis-assembly: remove the pickguard screws (leaving pickup screws, pots and switch untouched).

  • Remove the jack plate, desolder or cut the output jack wires, flip over the guitar and desolder the ground wire on the tremolo. Remove the pickguard with all electronics attached.

  • This method gives easy access to do electronics repairs/mods, without having to readjust pickup heights and individual components won't move around when you're soldering.

Schritt 10  ¶ 

Lift off the three pickup covers.

Schritt 10  ¶ 

  • Lift off the three pickup covers.

Schritt 11  ¶ 

Remove the springs which were on the underside of the pickups.

Schritt 11  ¶ 

  • Remove the springs which were on the underside of the pickups.

Schritt 12  ¶ 

Unscrew the two screws holding the lead input cover in place and lift off the cover.

Schritt 12  ¶ 

  • Unscrew the two screws holding the lead input cover in place and lift off the cover.

Schritt 13  ¶ 

Unscrew the input threaded bolt, which holds the output jack in place.

Schritt 13  ¶ 

  • Unscrew the input threaded bolt, which holds the output jack in place.

Schritt 14  ¶ 

Unscrew the screw holding the bottom strap button in position. Unscrew the screw holding the bottom strap button in position.

Schritt 14  ¶ 

  • Unscrew the screw holding the bottom strap button in position.

Schritt 15  ¶ 

Carry out the same process to remove the top strap button.

Schritt 15  ¶ 

  • Carry out the same process to remove the top strap button.

Schritt 16  ¶ 

Remove the six screws securing the bridge to the body.

Schritt 16  ¶ 

  • Remove the six screws securing the bridge to the body.

Schritt 17  ¶ 

Take out the six screws holding the white back plate in place.

Schritt 17  ¶ 

  • Take out the six screws holding the white back plate in place.

Schritt 18  ¶ 

Remove the three tremolo springs from the spring claw and tremolo block.

Schritt 18  ¶ 

  • Remove the three tremolo springs from the spring claw and tremolo block.

Schritt 19  ¶ 

Unscrew the two screws holding the spring claw to the body.

Schritt 19  ¶ 

  • Unscrew the two screws holding the spring claw to the body.

Schritt 20  ¶ 

Remove Bridge from main body.

Schritt 20  ¶ 

  • Remove Bridge from main body.

Schritt 21  ¶ 

Unscrew chrome parts.

Schritt 21  ¶ 

  • Unscrew chrome parts.

Schritt 22  ¶ 

Undo the 6 screws holding the saddles to the bridge. Then remove the spring and unscrew the 12 threaded bars. Undo the 6 screws holding the saddles to the bridge. Then remove the spring and unscrew the 12 threaded bars. Undo the 6 screws holding the saddles to the bridge. Then remove the spring and unscrew the 12 threaded bars.

Schritt 22  ¶ 

  • Undo the 6 screws holding the saddles to the bridge. Then remove the spring and unscrew the 12 threaded bars.

Schritt 23  ¶ 

Unscrew bridge from the tremolo block.

Schritt 23  ¶ 

  • Unscrew bridge from the tremolo block.

Schritt 24  ¶ 

Remove the four wood screws holding the neck to the body of the guitar.

Schritt 24  ¶ 

  • Remove the four wood screws holding the neck to the body of the guitar.

Schritt 25  ¶ 

Pull neck away from main body.

Schritt 25  ¶ 

  • Pull neck away from main body.

Schritt 26  ¶ 

Unscrew the two small screws securing the string trees to the headstock.

Schritt 26  ¶ 

  • Unscrew the two small screws securing the string trees to the headstock.

Schritt 27  ¶ 

Unscrew the tuner bushings with a 10mm hex driver

Schritt 27  ¶ 

  • Unscrew the tuner bushings with a 10mm hex driver

Schritt 28  ¶ 

Push the tuners from the front to pop them loose. It make take a bit of force if the alignment peg is stuck. Some use screws instead.

Schritt 28  ¶ 

  • Push the tuners from the front to pop them loose. It make take a bit of force if the alignment peg is stuck. Some use screws instead.

Schritt 29  ¶ 

Remove the tension screw followed by the tuner button, metal and then fiber washer.

Schritt 29  ¶ 

  • Remove the tension screw followed by the tuner button, metal and then fiber washer.