Zum Hauptinhalt wechseln
Hilfe

Nikon Coolpix 3200 Teardown

Teardown

Teardown

Teardowns bieten einen Einblick in ein device und sollten nicht als Demontageanleitung verwendet werden.

Benötigt Bessere Bilder

Benötigt Bessere Bilder

Schönere Fotos werden diese Anleitung verbessern. Trage dazu bei, indem du die Alten bearbeitest oder Neue aufnimmst und hochlädst!

Fehlende Schritte

Fehlende Schritte

Ups! In dieser Anleitung fehlen momentan einige wichtige Schritte.

Anleitung eines Mitglieds

Anleitung eines Mitglieds

Ein großartiges Mitglied unserer Community hat diese Anleitung erstellt. Sie wird nicht von iFixit Mitarbeitern überprüft.

Here is the disassembly for a Nikon Coolpix 3200 digital camera.

Schritt 1 Nikon Coolpix 3200 Teardown  ¶ 

Use a small Philips screwdriver to remove the screws from the base of the camera.

Schritt 1 Nikon Coolpix 3200 Teardown  ¶ 

  • Use a small Philips screwdriver to remove the screws from the base of the camera.

Schritt 2  ¶ 

Use a small Philips screwdriver to remove the screws from the side of the camera where the computer lead is.

Schritt 2  ¶ 

  • Use a small Philips screwdriver to remove the screws from the side of the camera where the computer lead is.

Schritt 3  ¶ 

Use a small Philips screwdriver to remove the two screws from the side of the camera where the card reader is.

Schritt 3  ¶ 

  • Use a small Philips screwdriver to remove the two screws from the side of the camera where the card reader is.

Schritt 4  ¶ 

Pry apart the outer casing. A gray plastic threaded piece (used to attach camera to a tripod) will fall out.

Schritt 4  ¶ 

  • Pry apart the outer casing. A gray plastic threaded piece (used to attach camera to a tripod) will fall out.

Schritt 5  ¶ 

Use a Phillips screwdriver to remove the two silver screws that connect the circuit board to the outer front casing.

Schritt 5  ¶ 

  • Use a Phillips screwdriver to remove the two silver screws that connect the circuit board to the outer front casing.

Schritt 6  ¶ 

Pry apart the front outer casing from the circuit board. The camera will now be in three pieces.

Schritt 6  ¶ 

  • Pry apart the front outer casing from the circuit board. The camera will now be in three pieces.

Schritt 7  ¶ 

Pull the connecting strip on the circuit board which connects it to the back outer casing. Pull the connecting strip on the circuit board which connects it to the back outer casing.

Schritt 7  ¶ 

  • Pull the connecting strip on the circuit board which connects it to the back outer casing.

Schritt 8  ¶ 

Use a Philips screwdriver to remove the two screws next to the computer port and the brass screw on the circuit board. Use a Philips screwdriver to remove the two screws next to the computer port and the brass screw on the circuit board.

Schritt 8  ¶ 

  • Use a Philips screwdriver to remove the two screws next to the computer port and the brass screw on the circuit board.

Schritt 9  ¶ 

Use a Phillips screwdriver to unscrew the three screws that connect the outer lens rim to the front casing. Use a Phillips screwdriver to unscrew the three screws that connect the outer lens rim to the front casing.

Schritt 9  ¶ 

  • Use a Phillips screwdriver to unscrew the three screws that connect the outer lens rim to the front casing.

Schritt 10  ¶ 

Use a Philips screwdriver to remove the three screws that hold the flash cover to the outer front casing. Use a Philips screwdriver to remove the three screws that hold the flash cover to the outer front casing.

Schritt 10  ¶ 

  • Use a Philips screwdriver to remove the three screws that hold the flash cover to the outer front casing.

Schritt 11  ¶ 

Open the lid of the battery compartment and use a Philips screwdriver to remove the two screws at the bottom.

Schritt 11  ¶ 

  • Open the lid of the battery compartment and use a Philips screwdriver to remove the two screws at the bottom.

Schritt 12  ¶ 

Use a Phillips screwdriver to unscrew the two screws that connect the inside battery casing to the front of the outer casing.

Schritt 12  ¶ 

  • Use a Phillips screwdriver to unscrew the two screws that connect the inside battery casing to the front of the outer casing.

Schritt 13  ¶ 

Pull off the battery casing from the inside of the outer front casing. The circuit board, battery casing, and front outer casing will be attached by a connecting strip along with red and black wires.

Schritt 13  ¶ 

  • Pull off the battery casing from the inside of the outer front casing. The circuit board, battery casing, and front outer casing will be attached by a connecting strip along with red and black wires.

Schritt 14  ¶ 

Use scissors to cut the red and black wires away from the battery points of contact.

Schritt 14  ¶ 

  • Use scissors to cut the red and black wires away from the battery points of contact.

Schritt 15  ¶ 

Pull the connecting strip away from the circuit board to separate it from the front casing.

Schritt 15  ¶ 

  • Pull the connecting strip away from the circuit board to separate it from the front casing.

Schritt 16  ¶ 

Use a Philips screwdriver to unscrew the two screws that connect the photo button to the outer front casing.

Schritt 16  ¶ 

  • Use a Philips screwdriver to unscrew the two screws that connect the photo button to the outer front casing.

Schritt 17  ¶ 

Firmly press on the photo button and this component will pop out.

Schritt 17  ¶ 

  • Firmly press on the photo button and this component will pop out.

Schritt 18  ¶ 

Use a scalpel to pry apart the metal inner part of the button from the plastic outer piece. Use a scalpel to pry apart the metal inner part of the button from the plastic outer piece.

Schritt 18  ¶ 

  • Use a scalpel to pry apart the metal inner part of the button from the plastic outer piece.

Schritt 19  ¶ 

Use your fingernails to peel the outer rim from the front casing. Use your fingernails to peel the outer rim from the front casing.

Schritt 19  ¶ 

  • Use your fingernails to peel the outer rim from the front casing.

Schritt 20  ¶ 

Kein Bild

Schritt 20  ¶ 

  • Pull the connecting strip out of the circuit board to separate it from the LCD screen.

Schritt 21  ¶ 

Kein Bild

Schritt 21  ¶ 

  • Use your fingernails to pry apart the back metal piece of the screen (covered by a black plastic film) from the front section of the screen.

Schritt 22  ¶ 

Pry apart the back black piece and front white piece of the screen. Inside the screen there are four sheets of plastic: one opaque, two mirrored, and one thicker plastic sheet which has a foil piece attached to it.

Schritt 22  ¶ 

  • Pry apart the back black piece and front white piece of the screen. Inside the screen there are four sheets of plastic: one opaque, two mirrored, and one thicker plastic sheet which has a foil piece attached to it.

Schritt 23  ¶ 

Kein Bild

Schritt 23  ¶ 

  • Use a hammer and chisel to separate the lens piece of the camera from the circuit board.

Schritt 24  ¶ 

Kein Bild

Schritt 24  ¶ 

  • Use your fingernails to pry off the motor, motor cover, and flash piece from the lens piece of the camera.