Zum Hauptinhalt wechseln
Hilfe

Toshiba Satellite P205-S8811 Monitor Replacement

Benötigt Bessere Bilder

Benötigt Bessere Bilder

Schönere Fotos werden diese Anleitung verbessern. Trage dazu bei, indem du die Alten bearbeitest oder Neue aufnimmst und hochlädst!

This guide will demonstrate how to replace the monitor.

  • Autor: Bradley Johnson
  • Geschätzte Zeit: 20 - 30 Minuten
  • Schwierigkeitsgrad: Schwierig

If your monitor is malfunctioning and/or needs to be replaced, follow the steps in this guide.

Abschnitte
Werkzeuge

Schritt 1 Monitor  ¶ 

Unscrew the 4mm Phillips #1 screw holding the hard drive cover on. Place one finger underneath the tab of the hard drive cover and lift it up with medium force to take it off.

Schritt 1 Monitor  ¶ 

  • Unscrew the 4mm Phillips #1 screw holding the hard drive cover on.

  • Place one finger underneath the tab of the hard drive cover and lift it up with medium force to take it off.

Schritt 2  ¶ 

Grab the black tab attached to the hard drive and pull it to the left with a medium force until it pops out of its socket. Grab the black tab attached to the hard drive and pull it to the left with a medium force until it pops out of its socket.

Schritt 2  ¶ 

  • Grab the black tab attached to the hard drive and pull it to the left with a medium force until it pops out of its socket.

Schritt 3  ¶ 

Remove the two 8mm Phillips #1 screws from the back side of the laptop.

Schritt 3  ¶ 

  • Remove the two 8mm Phillips #1 screws from the back side of the laptop.

Schritt 4  ¶ 

Remove the four 8mm Phillips #1 screws located on the corners below the monitor.

Schritt 4  ¶ 

  • Remove the four 8mm Phillips #1 screws located on the corners below the monitor.

Schritt 5  ¶ 

Remove the two 4mm Phillips #1 screws located between the screws removed in the last step.

Schritt 5  ¶ 

  • Remove the two 4mm Phillips #1 screws located between the screws removed in the last step.

Schritt 6  ¶ 

Unplug the black wire connecting the monitor to the motherboard by pulling it lightly towards you. Unplug the black/red wire that also connects the monitor to the motherboard by pulling lightly away from you.

Schritt 6  ¶ 

  • Unplug the black wire connecting the monitor to the motherboard by pulling it lightly towards you.

  • Unplug the black/red wire that also connects the monitor to the motherboard by pulling lightly away from you.

Schritt 7  ¶ 

Remove the three colored wires (white, grey, and black) that are all connected beside each other by pulling them up lightly. Remove the three colored wires (white, grey, and black) that are all connected beside each other by pulling them up lightly. Remove the three colored wires (white, grey, and black) that are all connected beside each other by pulling them up lightly.

Schritt 7  ¶ 

  • Remove the three colored wires (white, grey, and black) that are all connected beside each other by pulling them up lightly.

Schritt 8  ¶ 

Gently pull out the wide, white wire coming from the monitor.

Schritt 8  ¶ 

  • Gently pull out the wide, white wire coming from the monitor.

Schritt 9  ¶ 

Use a plastic opening tool to loosen the top panel by placing the tool underneath the panel at several points and then lifting upwards with a medium force. You will know it is loose if it makes a loud clicking noise. Place your fingers on the side of the panel closest to the monitor. Lift up on that side of the panel with a large amount of force in order to pry it off.

Schritt 9  ¶ 

  • Use a plastic opening tool to loosen the top panel by placing the tool underneath the panel at several points and then lifting upwards with a medium force. You will know it is loose if it makes a loud clicking noise.

  • Place your fingers on the side of the panel closest to the monitor. Lift up on that side of the panel with a large amount of force in order to pry it off.

Schritt 10  ¶ 

Remove the 8mm Phillips #1 screw located just below the large gray wire. Remove the 8mm Phillips #1 screw located to the right of the left-hand speaker. Remove the 4mm Phillips #1 screw located above the fan and next to the large gray wire.

Schritt 10  ¶ 

  • Remove the 8mm Phillips #1 screw located just below the large gray wire.

  • Remove the 8mm Phillips #1 screw located to the right of the left-hand speaker.

  • Remove the 4mm Phillips #1 screw located above the fan and next to the large gray wire.

Schritt 11  ¶ 

Remove the large gray wire that is connected to the motherboard to the right of the fan. Remove the small white/grey wire that is connected at the top of the fan.

Schritt 11  ¶ 

  • Remove the large gray wire that is connected to the motherboard to the right of the fan.

  • Remove the small white/grey wire that is connected at the top of the fan.

Schritt 12  ¶ 

Grabbing both sides of the monitor, gently lift the it out of place and set it aside.

Schritt 12  ¶ 

  • Grabbing both sides of the monitor, gently lift the it out of place and set it aside.