Zum Hauptinhalt wechseln
Hilfe

Memory Cage with Rear Fan (Early 2008) Replacement

Anleitung eines Mitglieds

Anleitung eines Mitglieds

Ein großartiges Mitglied unserer Community hat diese Anleitung erstellt. Sie wird nicht von iFixit Mitarbeitern überprüft.

Action Shots

Action Shots

Sei ein Actionheld! Diese Anleitung benötigt Bilder, damit besser veranschaulicht werden kann, wie bestimmte Handgriffe ausgeführt werden.

Removing and/or replacing the Memory Cage with Rear Fan.

  • Autor: Joshua Byrne
  • Geschätzte Zeit: 30 - 45 Minuten
  • Schwierigkeitsgrad: Moderat

Removing and/or replacing the Memory Cage with Rear Fan.

Schritt 1 Memory Cage with Rear Fan (Early 2008)  ¶ 

Disconnect the rear fan cable from the logic board. Disconnect the rear fan cable from the logic board.

Schritt 1 Memory Cage with Rear Fan (Early 2008)  ¶ 

  • Disconnect the rear fan cable from the logic board.

Schritt 2  ¶ 

Using a long-handled, magnetized #1 Phillips screwdriver, loosen the four captive screws that mount the memory cage to the logic board.

Schritt 2  ¶ 

  • Using a long-handled, magnetized #1 Phillips screwdriver, loosen the four captive screws that mount the memory cage to the logic board.

  • Rotate the computer so that it is standing vertically. Using a magnetized short-handled or right-angled jeweler’s #1 Phillips screwdriver, carefully remove the two short screws that mount the memory cage to the bottom panel of the enclosure.

Schritt 3  ¶ 

Note: To remove the memory cage and fan, you must first slide the fan partway into the cage. The fan is held in place by three latches, which you must release before sliding the fan.

Schritt 3  ¶ 

  • Note: To remove the memory cage and fan, you must first slide the fan partway into the cage. The fan is held in place by three latches, which you must release before sliding the fan.

  • Using your forefinger, reach below the fan and release the latch nearest the logic board.

Schritt 4  ¶ 

Using a flat-blade screwdriver, release the two latches nearest the front of the computer.

Schritt 4  ¶ 

  • Using a flat-blade screwdriver, release the two latches nearest the front of the computer.

Schritt 5  ¶ 

Slide the rear fan into the memory cage.

Schritt 5  ¶ 

  • Slide the rear fan into the memory cage.

Schritt 6  ¶ 

Slide the memory cage and fan toward the power supply far enough that the cage clears the bottom edge of the enclosure. Then lift the memory cage and fan out of the enclosure.

Schritt 6  ¶ 

  • Slide the memory cage and fan toward the power supply far enough that the cage clears the bottom edge of the enclosure. Then lift the memory cage and fan out of the enclosure.

Schritt 7  ¶ 

Replacement Note: If you are installing a new fan in the memory cage assembly, rotate the fan into the cage as illustrated. Also note carefully the orientaton of the fan in relation to the cage.

Schritt 7  ¶ 

  • Replacement Note: If you are installing a new fan in the memory cage assembly, rotate the fan into the cage as illustrated. Also note carefully the orientaton of the fan in relation to the cage.

Schritt 8  ¶ 

Important: Before you install the cage in the enclosure, the fan should always be inserted partway into the cage. Replacement Note: Before installing the memory cage and fan, make sure all logic board cables below the cage are out of the way so that the cage sits properly and the cables are not pinched or damaged when you tighten the screws.

Schritt 8  ¶ 

  • Important: Before you install the cage in the enclosure, the fan should always be inserted partway into the cage.

  • Replacement Note: Before installing the memory cage and fan, make sure all logic board cables below the cage are out of the way so that the cage sits properly and the cables are not pinched or damaged when you tighten the screws.

  • Replacement Note: To install the memory cage and fan, maneuver the cage into position in the enclosure. Tighten at least two of the captive mounting screws. Then slide the fan toward the back panel, until you hear it snap into place.