Zum Hauptinhalt wechseln
Hilfe

Technik: Removing a Cracked Front Panel

Potenziell gefährlich

Potenziell gefährlich

Es besteht Verletzungsgefahr, wenn die Anweisungen nicht ordnungsgemäß befolgt werden. Sei vorsichtig und befolge alle Warnhinweise.

Follow this guide to safely remove a cracked digitizer from your iPad.

This procedure is not for the faint of heart. It is very difficult, and can be dangerous if you are not careful and properly equipped. Read the entire procedure before you begin to be sure you're up to the task.

This guide is intended as a generic supplement guide, and should be followed alongside the standard front panel replacement guide for any iPad or iPad Mini.

Schritt 1 Removing a Cracked Front Panel  ¶ 

Use your hot iOpener to heat up all four edges of the front panel. Let the iOpener rest on each edge for at least 90 seconds, microwaving for 30 seconds at a time as needed.

Schritt 1 Removing a Cracked Front Panel  ¶ 

  • Use your hot iOpener to heat up all four edges of the front panel. Let the iOpener rest on each edge for at least 90 seconds, microwaving for 30 seconds at a time as needed.

  • Take your time and ensure the entire bezel is warm. The more time you spend on this, the less time you'll spend picking out glass shards in the next steps.

  • Once all of the adhesive is warmed, pick out the edge with the largest uncracked section of glass.

  • Try using a suction up to pull up on this section, and then wedge a guitar pick beneath the glass.

  • If the glass is too badly cracked for the suction cup to grab, apply more heat and force the pick in, careful not to damage the LCD.

Schritt 2  ¶ 

Work your way around the entire perimeter of the front panel with an opening pick. Much of the glass around the bezel will break off from the rest of the panel, and will stay adhered to the rear case of the iPad. Work your way past these pieces to free as much of the glass panel as possible.

Schritt 2  ¶ 

  • Work your way around the entire perimeter of the front panel with an opening pick.

  • Much of the glass around the bezel will break off from the rest of the panel, and will stay adhered to the rear case of the iPad. Work your way past these pieces to free as much of the glass panel as possible.

  • When you get to the digitizer and (on iPad 4) home button cables, you may find it helpful to cut these cables, rather than risk ripping them out of their sockets and damaging the logic board.

  • Remove the taped-together glass panel from the iPad. Be careful as this will have sharp edges and may drop pieces of glass. Dispose of safely.

Schritt 3  ¶ 

For the next step, you'll need to apply your iOpener directly to the broken glass left adhered to the iPad. To protect your iOpener from the glass and keep it from filling with glass dust, stick some masking tape to one side. Heat the iOpener and apply it to one edge of the iPad, directly on top of the pieces of glass that are still adhered to the rear case of the iPad.

Schritt 3  ¶ 

  • For the next step, you'll need to apply your iOpener directly to the broken glass left adhered to the iPad.

  • To protect your iOpener from the glass and keep it from filling with glass dust, stick some masking tape to one side.

  • Heat the iOpener and apply it to one edge of the iPad, directly on top of the pieces of glass that are still adhered to the rear case of the iPad.

  • Leave the iOpener there for at least 90 seconds, to soften the adhesive holding these small pieces in place.

  • Be careful not to touch or otherwise disturb the LCD.

Schritt 4  ¶ 

Did you take off your safety glasses? If so, put them back on now. Seriously. Grab your favorite plastic tool and start prying out the remaining pieces of glass from the iPad frame.

Schritt 4  ¶ 

  • Did you take off your safety glasses? If so, put them back on now. Seriously.

  • Grab your favorite plastic tool and start prying out the remaining pieces of glass from the iPad frame.

  • This is a slow and tedious process, but benefits greatly from heating the adhesive.

  • There is a serious risk of cutting yourself while working with this glass. Work slowly and with controlled force. You may wish to wear thin leather gloves.

  • Remove all of the glass and residual adhesive and continue your repair.