Zum Hauptinhalt wechseln
Hilfe

Samsung Galaxy Note 8.0 Screen Assembly Replacement

You will be replacing the digitizer and LCD assembly. This guide also shows steps to replace just the screen digitizer without the replacing the LCD.

  • Autor: James Laubaugh
  • Geschätzte Zeit: 1 Stunde
  • Schwierigkeitsgrad: Schwierig

The screen digitizer is the clear glass like protection for the LCD. The screen digitizer is also what registers your touch inputs. The LCD is located underneath the screen digitizer and is the component that displays the images. These steps can be used to replace just the screen if it is cracked or damaged or just the LCD if you have no display at all.

Werkzeuge (fortgesetzt)
Relevante Ersatzteile

Schritt 1 Screen Digitizer and LCD  ¶ 

Gently pull the tan part of the digitizer connector up. Carefully slide the orange ribbon out from connector.

Schritt 1 Screen Digitizer and LCD  ¶ 

  • Gently pull the tan part of the digitizer connector up.

  • Carefully slide the orange ribbon out from connector.

Schritt 2  ¶ 

Gently pull up the black part of the LCD connector. Carefully slide orange ribbon out from connector.

Schritt 2  ¶ 

  • Gently pull up the black part of the LCD connector.

  • Carefully slide orange ribbon out from connector.

Schritt 3  ¶ 

Turn the tablet over screen up. Set your heat gun or blow dryer to the medium heat setting.

Schritt 3  ¶ 

  • Turn the tablet over screen up. Set your heat gun or blow dryer to the medium heat setting.

  • Sweep the heat gun over the white edge of the tablet screen. Apply heat for 30 seconds on each side before moving to the next side.

  • You will repeat a circular pattern bottom, left, top and then right. Repeat this pattern 3 times spending 30 seconds on each side.

  • As an alternative to a heat gun, you can use an iOpener: iOpener Anleitung

Schritt 4  ¶ 

Insert your plastic opening tool between the silver surround and the screen, starting at the top of the tablet.

Schritt 4  ¶ 

  • Insert your plastic opening tool between the silver surround and the screen, starting at the top of the tablet.

Schritt 5  ¶ 

It is important that you separate the 3 edges only at this time. The side of the tablet opposite the power button has a connection that could be damaged if this side is separated.

Schritt 5  ¶ 

  • It is important that you separate the 3 edges only at this time. The side of the tablet opposite the power button has a connection that could be damaged if this side is separated.

  • Slide your opening tool down the side of the device with the volume and power buttons. Continue sliding down the side toward the home button until the glue is free on this side.

Schritt 6  ¶ 

Slide your opening tool down the home button edge until the glue is free on this side.

Schritt 6  ¶ 

  • Slide your opening tool down the home button edge until the glue is free on this side.

Schritt 7  ¶ 

Turn the tablet over and carefully press out the LCD panel from the back along the power button edge only. Push gently on the back of the LCD in the battery opening. Disconnect ribbon that is connecting the screen assembly to the motherboard Disconnect ribbon that is connecting the screen assembly to the motherboard

Schritt 7  ¶ 

  • Turn the tablet over and carefully press out the LCD panel from the back along the power button edge only. Push gently on the back of the LCD in the battery opening.

  • Disconnect ribbon that is connecting the screen assembly to the motherboard

Schritt 8  ¶ 

When inserting your opening tool on the side opposite the power button, avoid the screen cable located 7 cm from the top of the device.

Schritt 8  ¶ 

  • When inserting your opening tool on the side opposite the power button, avoid the screen cable located 7 cm from the top of the device.

  • Turn the tablet over and completely remove the LCD and screen assembly from the tablet by sliding a plastic opening tool down the final edge until the adhesive is free.

  • If you are replacing the screen by itself, continue to the next step. If you are replacing the screen digitizer only, simply follow the procedures in reverse to complete the replacement.

Schritt 9  ¶ 

To separate the screen from the LCD you will need to heat the adhesive holding the two together.

Schritt 9  ¶ 

  • To separate the screen from the LCD you will need to heat the adhesive holding the two together.

  • Holding the heat gun, set to medium, approximately 6 inches from the screen, sweep from left to right as you move the heat gun across the tablet from top to bottom.

  • Continue heating the screen from top to bottom as you sweep from left to right for 5 minutes.

Schritt 10  ¶ 

Find a plastic card you no longer need.

Schritt 10  ¶ 

  • Find a plastic card you no longer need.

  • It will be covered in adhesive when you're done.

  • Slide the card between the screen and digitizer working around the edges toward the center.