Zum Hauptinhalt wechseln
Hilfe

Brother PT-1010 Keyboard Replacement

Bessere Einleitung

Bessere Einleitung

Verbessere diese Anleitung, indem du die Einleitung vervollständigst oder überarbeitest.

This guide will show you how to remove and replace the keyboard of your Brother PT-1010 label maker.

  • Autor: Haley Sweet
  • Geschätzte Zeit: 5 Minuten
  • Schwierigkeitsgrad: Moderat

Schritt 1 Remove Back Cover  ¶ 

Flip the device over and press down on the indication arrows located at the top center of the back cover and pull it open.

Schritt 1 Remove Back Cover  ¶ 

  • Flip the device over and press down on the indication arrows located at the top center of the back cover and pull it open.

Schritt 2  ¶ 

Remove batteries, cassette tape, and cutter blade.

Schritt 2  ¶ 

  • Remove batteries, cassette tape, and cutter blade.

Schritt 3 Remove Screws  ¶ 

Use a phillips size #00 screwdriver to unscrew the 5 corner screws circled in the picture.

Schritt 3 Remove Screws  ¶ 

  • Use a phillips size #00 screwdriver to unscrew the 5 corner screws circled in the picture.

Schritt 4 Separate Device  ¶ 

Separate the top of the device from the bottom. Be very cautious when you separate the device, there is a ribbon attaching the top to the bottom.

Schritt 4 Separate Device  ¶ 

  • Separate the top of the device from the bottom. Be very cautious when you separate the device, there is a ribbon attaching the top to the bottom.

Schritt 5 Remove side panels  ¶ 

Remove the two black side panels. They will easily fall out so just move them to the side until you are putting your device back together.

Schritt 5 Remove side panels  ¶ 

  • Remove the two black side panels. They will easily fall out so just move them to the side until you are putting your device back together.

Schritt 6 Pull Ribbon Out  ¶ 

Using your index finger and thumb, pull out the golden ribbon from the green circuit board. Using your index finger and thumb, pull out the golden ribbon from the green circuit board. Using your index finger and thumb, pull out the golden ribbon from the green circuit board.

Schritt 6 Pull Ribbon Out  ¶ 

  • Using your index finger and thumb, pull out the golden ribbon from the green circuit board.

Schritt 7 Remove Screws from Circuit Board  ¶ 

Use a phillips size #00 screwdriver to remove the two screws, circled in red, from the green circuit board.

Schritt 7 Remove Screws from Circuit Board  ¶ 

  • Use a phillips size #00 screwdriver to remove the two screws, circled in red, from the green circuit board.

Schritt 8 Remove Circuit Board  ¶ 

Carefully remove the green circuit board by pulling it straight up. Be careful not to break the LCD cable ribbon that connects the circuit board to the device.

Schritt 8 Remove Circuit Board  ¶ 

  • Carefully remove the green circuit board by pulling it straight up. Be careful not to break the LCD cable ribbon that connects the circuit board to the device.

  • The ribbon is very fragile so be careful to break it when pulling up on the circuit board.

Schritt 9 Peel Off Rubber Keyboard  ¶ 

Underneath the circuit board you will find the rubber keyboard. Peel this off and remove it from the device. Underneath the circuit board you will find the rubber keyboard. Peel this off and remove it from the device. Underneath the circuit board you will find the rubber keyboard. Peel this off and remove it from the device.

Schritt 9 Peel Off Rubber Keyboard  ¶ 

  • Underneath the circuit board you will find the rubber keyboard. Peel this off and remove it from the device.