Zum Hauptinhalt wechseln
Hilfe

Technik: iPad Air 2 Wi-Fi Opening Procedure

Nicht eigenständige Anleitung

Nicht eigenständige Anleitung

Bitte beachte, dass diese Anleitung nur eine grundständige Anleitung für andere Anleitungen ist.

Opening procedure for the iPad Air 2 Wi-Fi.

Remove the front panel assembly from an iPad Air 2 to access any internal component for repair or replacement.

Schritt 1 iPad Air 2 Wi-Fi Opening Procedure  ¶ 

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass. Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered. This will keep glass shards contained and provide structural integrity when prying and lifting the display.

Schritt 1 iPad Air 2 Wi-Fi Opening Procedure  ¶ 

  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.

  • Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.

  • This will keep glass shards contained and provide structural integrity when prying and lifting the display.

  • Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.

  • Wear safety glasses to protect your eyes, and be careful not to damage the LCD screen.

Schritt 2  ¶ 

The following steps involve using an iOpener to soften the adhesive holding the front panel assembly in place. When using the iOpener, be sure to heat it in the microwave for no more than 30 seconds.

Schritt 2  ¶ 

  • The following steps involve using an iOpener to soften the adhesive holding the front panel assembly in place. When using the iOpener, be sure to heat it in the microwave for no more than 30 seconds.

  • Handling it by the tabs on either end, place a heated iOpener over the top edge of the iPad.

  • Let the iOpener sit on the iPad for two minutes to soften the adhesive securing the front panel to the rest of the iPad.

Schritt 3  ¶ 

While the iPad looks uniform from the outside, there are delicate components under certain portions of the front glass. To avoid damage, only heat and pry in the areas described in each step. As you follow the directions, take special care to avoid prying in the following areas: Home Button

Schritt 3  ¶ 

  • While the iPad looks uniform from the outside, there are delicate components under certain portions of the front glass. To avoid damage, only heat and pry in the areas described in each step.

  • As you follow the directions, take special care to avoid prying in the following areas:

  • Home Button

  • Front Facing Camera

  • Main Camera

Schritt 4  ¶ 

Place a suction cup over the iPad's front-facing camera and press down to create a seal. To get the most leverage, place the suction cup as close to the edge as possible without going past the edge of the display.

Schritt 4  ¶ 

  • Place a suction cup over the iPad's front-facing camera and press down to create a seal.

  • To get the most leverage, place the suction cup as close to the edge as possible without going past the edge of the display.

Schritt 5  ¶ 

Firmly pull up on the suction cup to to create a small gap between the front panel and the rear case. Do not pull too hard or you may shatter the glass. Once you've opened a sufficient gap, insert an opening pick into the gap to prevent the adhesive from resealing.

Schritt 5  ¶ 

  • Firmly pull up on the suction cup to to create a small gap between the front panel and the rear case.

  • Do not pull too hard or you may shatter the glass.

  • Once you've opened a sufficient gap, insert an opening pick into the gap to prevent the adhesive from resealing.

Schritt 6  ¶ 

Slide the pick along the edge of the display, towards the headphone jack. If there is still a considerable amount of resistance when sliding the opening pick, repeat the iOpener heating procedure and apply additional heat. Be careful not to let the opening pick slide between the fused LCD and front panel, as doing so can permanently damage the display.

Schritt 6  ¶ 

  • Slide the pick along the edge of the display, towards the headphone jack.

  • If there is still a considerable amount of resistance when sliding the opening pick, repeat the iOpener heating procedure and apply additional heat.

  • Be careful not to let the opening pick slide between the fused LCD and front panel, as doing so can permanently damage the display.

  • A good rule of thumb is to never insert the opening pick more than a quarter inch (6 mm) into the iPad.

Schritt 7  ¶ 

Insert a second opening pick by the front-facing camera. Insert a second opening pick by the front-facing camera.

Schritt 7  ¶ 

  • Insert a second opening pick by the front-facing camera.

Schritt 8  ¶ 

Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button. Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button. Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button.

Schritt 8  ¶ 

  • Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button.

Schritt 9  ¶ 

Insert a third pick by the front-facing camera. Insert a third pick by the front-facing camera.

Schritt 9  ¶ 

  • Insert a third pick by the front-facing camera.

Schritt 10  ¶ 

Bring the right opening pick down and around the top right corner of the iPad. Bring the right opening pick down and around the top right corner of the iPad. Bring the right opening pick down and around the top right corner of the iPad.

Schritt 10  ¶ 

  • Bring the right opening pick down and around the top right corner of the iPad.

Schritt 11  ¶ 

Bring the left opening pick around the top left corner of the tablet. Bring the left opening pick around the top left corner of the tablet. Bring the left opening pick around the top left corner of the tablet.

Schritt 11  ¶ 

  • Bring the left opening pick around the top left corner of the tablet.

Schritt 12  ¶ 

Reheat the iOpener and lay it over the right edge of the display to loosen the adhesive underneath.

Schritt 12  ¶ 

  • Reheat the iOpener and lay it over the right edge of the display to loosen the adhesive underneath.

Schritt 13  ¶ 

Slide the right opening pick roughly halfway down the display. Slide the right opening pick roughly halfway down the display. Slide the right opening pick roughly halfway down the display.

Schritt 13  ¶ 

  • Slide the right opening pick roughly halfway down the display.

Schritt 14  ¶ 

Reheat the iOpener and apply heat to the left side of the iPad.

Schritt 14  ¶ 

  • Reheat the iOpener and apply heat to the left side of the iPad.

Schritt 15  ¶ 

Slide the left-hand opening pick about halfway down the edge of the display. Slide the left-hand opening pick about halfway down the edge of the display. Slide the left-hand opening pick about halfway down the edge of the display.

Schritt 15  ¶ 

  • Slide the left-hand opening pick about halfway down the edge of the display.

Schritt 16  ¶ 

Slide the opposite opening pick down to the bottom right corner of the iPad. If necessary, reheat the adhesive on the right edge to loosen the display assembly. If necessary, reheat the adhesive on the right edge to loosen the display assembly.

Schritt 16  ¶ 

  • Slide the opposite opening pick down to the bottom right corner of the iPad.

  • If necessary, reheat the adhesive on the right edge to loosen the display assembly.

Schritt 17  ¶ 

Slide the left-hand opening pick down the edge of the display until you reach the corner. Slide the left-hand opening pick down the edge of the display until you reach the corner. Slide the left-hand opening pick down the edge of the display until you reach the corner.

Schritt 17  ¶ 

  • Slide the left-hand opening pick down the edge of the display until you reach the corner.

Schritt 18  ¶ 

Use the iOpener to apply heat to the bottom edge of the iPad.

Schritt 18  ¶ 

  • Use the iOpener to apply heat to the bottom edge of the iPad.

Schritt 19  ¶ 

Bring the right-hand opening pick around the bottom corner of the iPad. Bring the right-hand opening pick around the bottom corner of the iPad. Bring the right-hand opening pick around the bottom corner of the iPad.

Schritt 19  ¶ 

  • Bring the right-hand opening pick around the bottom corner of the iPad.

Schritt 20  ¶ 

Repeat for the left-hand pick. Reheat and reapply the iOpener as needed. Always wait at least ten minutes before reheating the iOpener. Reheat and reapply the iOpener as needed. Always wait at least ten minutes before reheating the iOpener.

Schritt 20  ¶ 

  • Repeat for the left-hand pick.

  • Reheat and reapply the iOpener as needed. Always wait at least ten minutes before reheating the iOpener.

Schritt 21  ¶ 

Remove the right-hand opening pick at the bottom of the iPad. Remove the right-hand opening pick at the bottom of the iPad.

Schritt 21  ¶ 

  • Remove the right-hand opening pick at the bottom of the iPad.

Schritt 22  ¶ 

Slide the left-hand opening pick along the bottom edge of the display, then remove it from the bottom right corner of the iPad. Be very careful to not insert the pick more than a quarter inch (6 mm) into the display to avoid damaging the Home Button and display cables underneath. Be very careful to not insert the pick more than a quarter inch (6 mm) into the display to avoid damaging the Home Button and display cables underneath.

Schritt 22  ¶ 

  • Slide the left-hand opening pick along the bottom edge of the display, then remove it from the bottom right corner of the iPad.

  • Be very careful to not insert the pick more than a quarter inch (6 mm) into the display to avoid damaging the Home Button and display cables underneath.

Schritt 23  ¶ 

Twist the remaining pick by the front-facing camera to separate the top edge of the display assembly from the rear case. Twist the remaining pick by the front-facing camera to separate the top edge of the display assembly from the rear case. Twist the remaining pick by the front-facing camera to separate the top edge of the display assembly from the rear case.

Schritt 23  ¶ 

  • Twist the remaining pick by the front-facing camera to separate the top edge of the display assembly from the rear case.

Schritt 24  ¶ 

Continue lifting the display assembly from the front-facing camera side. Pull the display slightly away from the bottom edge to completely separate it from the rear case. Keep lifting until the display assembly is roughly perpendicular to the body of the iPad.

Schritt 24  ¶ 

  • Continue lifting the display assembly from the front-facing camera side.

  • Pull the display slightly away from the bottom edge to completely separate it from the rear case.

  • Keep lifting until the display assembly is roughly perpendicular to the body of the iPad.

  • Do not attempt to remove the display yet—it is still attached to the rear case by three delicate ribbon cables.

Schritt 25  ¶ 

Remove the single 1.8 mm Phillips screw securing the battery terminals to their contacts on the logic board.

Schritt 25  ¶ 

  • Remove the single 1.8 mm Phillips screw securing the battery terminals to their contacts on the logic board.

Schritt 26  ¶ 

To reduce the risk of a short, you can use a battery isolation pick to disconnect the battery. Slide a battery isolation pick underneath the battery connector area of the logic board, and leave it in place while you work.

Schritt 26  ¶ 

  • To reduce the risk of a short, you can use a battery isolation pick to disconnect the battery.

  • Slide a battery isolation pick underneath the battery connector area of the logic board, and leave it in place while you work.

Schritt 27  ¶ 

Remove the three 1.3mm Phillips screws from the display cable bracket. Remove the bracket. Remove the bracket.

Schritt 27  ¶ 

  • Remove the three 1.3mm Phillips screws from the display cable bracket.

  • Remove the bracket.

Schritt 28  ¶ 

Disconnect the display data connector from its socket on the logic board. Disconnect the display data connector from its socket on the logic board.

Schritt 28  ¶ 

  • Disconnect the display data connector from its socket on the logic board.

Schritt 29  ¶ 

Disconnect the two remaining digitizer cables underneath the display data cable. Disconnect the two remaining digitizer cables underneath the display data cable. Disconnect the two remaining digitizer cables underneath the display data cable.

Schritt 29  ¶ 

  • Disconnect the two remaining digitizer cables underneath the display data cable.

Schritt 30  ¶ 

Remove the front panel assembly from the rear case.

Schritt 30  ¶ 

  • Remove the front panel assembly from the rear case.