Zum Hauptinhalt wechseln
Hilfe

MacBook Core 2 Duo Optical Drive Replacement

Nicht eigenständige Anleitung

Nicht eigenständige Anleitung

Bitte beachte, dass diese Anleitung nur eine grundständige Anleitung für andere Anleitungen ist.

  • Autor: iRobot
  • Schwierigkeitsgrad: Moderat

Access the combo or SuperDrive.

Abschnitte

Schritt 1 Optical Drive  ¶ 

Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.

Schritt 1 Optical Drive  ¶ 

  • Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.

Schritt 2  ¶ 

Remove the two Phillips screws from the front edge of the optical drive.

Schritt 2  ¶ 

  • Remove the two Phillips screws from the front edge of the optical drive.

  • Two 3.25 mm Phillips #000, (Head: 4 mm. dia. x .3 mm thick)

Schritt 3  ¶ 

Disconnect the orange optical drive ribbon cable from the logic board. This cable can also be disconnected by prying straight up using a spudger.

Schritt 3  ¶ 

  • Disconnect the orange optical drive ribbon cable from the logic board. This cable can also be disconnected by prying straight up using a spudger.

Schritt 4  ¶ 

Disconnect the newly revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.

Schritt 4  ¶ 

  • Disconnect the newly revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.

Schritt 5  ¶ 

Disconnect the (once again) newly-revealed hard drive cable.

Schritt 5  ¶ 

  • Disconnect the (once again) newly-revealed hard drive cable.

Schritt 6  ¶ 

Peel up the foil tape between the fan and the optical drive. Lift the foil tape from the fan side, leaving it attached to the optical drive.

Schritt 6  ¶ 

  • Peel up the foil tape between the fan and the optical drive. Lift the foil tape from the fan side, leaving it attached to the optical drive.

  • During reassembly, be sure to route the cables beneath the tape before reattaching it.

Schritt 7  ¶ 

Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.

Schritt 7  ¶ 

  • Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.

Schritt 8  ¶ 

Remove the 2 mm Phillips #00 screw securing the optical drive.

Schritt 8  ¶ 

  • Remove the 2 mm Phillips #00 screw securing the optical drive.

  • The Bluetooth cable may be covering the screw. If so, carefully push it aside. You may need to unscrew the cable clip to free the cable enough.

Schritt 9  ¶ 

Lift the Bluetooth antenna board from the right side of the optical drive.

Schritt 9  ¶ 

  • Lift the Bluetooth antenna board from the right side of the optical drive.

Schritt 10  ¶ 

Deroute the hard drive cable from along the front of the optical drive.

Schritt 10  ¶ 

  • Deroute the hard drive cable from along the front of the optical drive.

Schritt 11  ¶ 

Lift the front edge of the optical drive and slide it up and out of the computer.

Schritt 11  ¶ 

  • Lift the front edge of the optical drive and slide it up and out of the computer.