Zum Hauptinhalt wechseln
Hilfe

Nikon Coolpix P4 LCD Screen Replacement

Aufzählungszeichen!

Aufzählungszeichen!

Ein verbesserter Einsatz von Markups und der Farbe bzw. Art von Aufzählungszeichen würde diese Anleitung verständlicher machen.

Empfohlene Anleitung

Empfohlene Anleitung

Diese Anleitung wird von den iFixit-Mitarbeitern als außergewöhnlich gut eingestuft.

Replace the LCD Screen

  • Autor: Luke Baumann
  • Geschätzte Zeit: 5 Minuten
  • Schwierigkeitsgrad: Moderat

This guide will walk you through the steps to replace the LCD screen for your camera.

Schritt 1 LCD Screen  ¶ 

Remove the four screws located on bottom of camera.     (.086in screws)

Schritt 1 LCD Screen  ¶ 

  • Remove the four screws located on bottom of camera. (.086in screws)

Schritt 2  ¶ 

Remove the two screws, then remove the panel. (.113in screws) Remove the two screws, then remove the panel. (.113in screws)

Schritt 2  ¶ 

  • Remove the two screws, then remove the panel. (.113in screws)

Schritt 3  ¶ 

Remove panel on right side (front view) by removing these two screws. (.196in screws) Remove single screw set underneath panel. (0.083in screw) Remove single screw set underneath panel. (0.083in screw)

Schritt 3  ¶ 

  • Remove panel on right side (front view) by removing these two screws. (.196in screws)

  • Remove single screw set underneath panel. (0.083in screw)

Schritt 4  ¶ 

Remove the two screws attaching the back panel to the body on the left side. (.188in screws)

Schritt 4  ¶ 

  • Remove the two screws attaching the back panel to the body on the left side. (.188in screws)

Schritt 5  ¶ 

Gently pull off back cover

Schritt 5  ¶ 

  • Gently pull off back cover

Schritt 6  ¶ 

Remove the two screws holding on the back panel.  Then remove the three screws on the A/V Out tab (left side). (.188in screws) Remove tab.

Schritt 6  ¶ 

  • Remove the two screws holding on the back panel. Then remove the three screws on the A/V Out tab (left side). (.188in screws)

  • Remove tab.

Schritt 7  ¶ 

Remove the two screws attaching the front panel to the body on the left side. (.18in screws)

Schritt 7  ¶ 

  • Remove the two screws attaching the front panel to the body on the left side. (.18in screws)

Schritt 8  ¶ 

Flip up front panel.

Schritt 8  ¶ 

  • Flip up front panel.

  • There should be wires still attaching the panel to body. DO NOT TRY TO PULL OFF COMPLETELY

Schritt 9  ¶ 

Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)

Schritt 9  ¶ 

  • Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)

Schritt 10  ¶ 

Carefully pull orange LCD connector up and out of the port.

Schritt 10  ¶ 

  • Carefully pull orange LCD connector up and out of the port.

  • Be careful to pull vertically while pushing the black tab upwards

Schritt 11  ¶ 

Remove the screw below the LCD (.124in)

Schritt 11  ¶ 

  • Remove the screw below the LCD (.124in)

Schritt 12  ¶ 

Carefully pull out the plug connecting the LCD to the motherboard.

Schritt 12  ¶ 

  • Carefully pull out the plug connecting the LCD to the motherboard.

Schritt 13  ¶ 

You can now remove the LCD from the camera body.

Schritt 13  ¶ 

  • You can now remove the LCD from the camera body.

  • Insert new LCD and reassemble using the steps in reverse order.