Zum Hauptinhalt wechseln
Hilfe

Nikon CoolPix S600 Front and Rear Casing Replacement

Benötigt Bessere Bilder

Benötigt Bessere Bilder

Schönere Fotos werden diese Anleitung verbessern. Trage dazu bei, indem du die Alten bearbeitest oder Neue aufnimmst und hochlädst!

Fehlende grundständige Anleitungen

Fehlende grundständige Anleitungen

In dieser Anleitung fehlen Informationen, wie man am besten anfängt. Erstelle eine grundständige Anleitung!

Bessere Einleitung

Bessere Einleitung

Verbessere diese Anleitung, indem du die Einleitung vervollständigst oder überarbeitest.

How to remove the camera's case to access the internal parts of the camera

Schritt 1 Front and Rear Casing  ¶ 

With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.

Schritt 1 Front and Rear Casing  ¶ 

  • With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.

Schritt 2  ¶ 

Remove the chrome side cover from the body of the camera.

Schritt 2  ¶ 

  • Remove the chrome side cover from the body of the camera.

Schritt 3  ¶ 

Remove the four 3.2 mm screws on the bottom of the camera.

Schritt 3  ¶ 

  • Remove the four 3.2 mm screws on the bottom of the camera.

Schritt 4  ¶ 

Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward) Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)

Schritt 4  ¶ 

  • Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward)

  • Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)

Schritt 5  ¶ 

Gently separate the back cover from the body of the camera. The back casing will still be connected to the circuit board by a ribbon

Schritt 5  ¶ 

  • Gently separate the back cover from the body of the camera.

  • The back casing will still be connected to the circuit board by a ribbon

Schritt 6  ¶ 

Use the tweezers to disconnect the ribbon from the circuit board.

Schritt 6  ¶ 

  • Use the tweezers to disconnect the ribbon from the circuit board.

Schritt 7  ¶ 

Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)

Schritt 7  ¶ 

  • Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)

Schritt 8  ¶ 

Gently separate the front cover from the body of the camera. The front casing will still be connected to the circuit board by a few wires

Schritt 8  ¶ 

  • Gently separate the front cover from the body of the camera.

  • The front casing will still be connected to the circuit board by a few wires

Schritt 9  ¶ 

Remove the two 3.2 mm screws that hold the flash to the front cover.

Schritt 9  ¶ 

  • Remove the two 3.2 mm screws that hold the flash to the front cover.

Schritt 10  ¶ 

Use the Spudger to remove the copper colored light bulb clip. Remove the front cover entierly from the camera body. Remove the front cover entierly from the camera body.

Schritt 10  ¶ 

  • Use the Spudger to remove the copper colored light bulb clip.

  • Remove the front cover entierly from the camera body.