Zum Hauptinhalt wechseln
Hilfe

Disassembling HP Photosmart c3180 Feed Roller Assembly Removal

Fehler in den Markups

Fehler in den Markups

Diese Anleitung benötigt bessere Markups. Hilf aus, indem du sie korrigierst oder einige Markup-Anmerkungen erstellst.

Removing the Feed Roller Assembly to get to the logic board and the feed roller, and to make cleaning the rollers easier.

  • Autor: Jim
  • Geschätzte Zeit: 20 - 30 Minuten
  • Schwierigkeitsgrad: Schwierig

Schritt 1 Feed Roller Assembly Removal  ¶ 

Set aside the ink cartridge carriage. Remove the three T10 12mm Torx screws holding the paper guide to the printer body.

Schritt 1 Feed Roller Assembly Removal  ¶ 

  • Set aside the ink cartridge carriage.

  • Remove the three T10 12mm Torx screws holding the paper guide to the printer body.

  • Lift the paper guide directly up to remove it and set it aside.

Schritt 2  ¶ 

Remove the four T10 12mm Torx screws from the roller holder. Remove the four T10 12mm Torx screws from the roller holder.

Schritt 2  ¶ 

  • Remove the four T10 12mm Torx screws from the roller holder.

Schritt 3  ¶ 

Remove the plastic gear cover by pulling it away from the printer body and lifting it up.

Schritt 3  ¶ 

  • Remove the plastic gear cover by pulling it away from the printer body and lifting it up.

Schritt 4  ¶ 

Remove the metal tab by rotating it away from the body of the printer and pulling up. Remove the brush by grasping it firmly by the base and lift straight up.

Schritt 4  ¶ 

  • Remove the metal tab by rotating it away from the body of the printer and pulling up.

  • Remove the brush by grasping it firmly by the base and lift straight up.

Schritt 5  ¶ 

Remove the pad holder by lifting it straight up.

Schritt 5  ¶ 

  • Remove the pad holder by lifting it straight up.

Schritt 6  ¶ 

Remove the connector holding the feed roller motor to the logic board by pulling it strait up Remove the T10 12mm Torx screw on the roller panel.

Schritt 6  ¶ 

  • Remove the connector holding the feed roller motor to the logic board by pulling it strait up

  • Remove the T10 12mm Torx screw on the roller panel.

Schritt 7  ¶ 

Disconnect the page sensor from the logic board by pulling straight up on the connector. Disconnect the page sensor from the logic board by pulling straight up on the connector.

Schritt 7  ¶ 

  • Disconnect the page sensor from the logic board by pulling straight up on the connector.

Schritt 8  ¶ 

Rotate the printer 180 degrees and turn it up on to the front side, so that the back of the printer is facing up and the bottom facing you. Be careful because the feed roller assembly is now loose, but it is still attached to the main body of the printer. Push in the tab on the left side of the back panel and pull outward to remove the back panel.

Schritt 8  ¶ 

  • Rotate the printer 180 degrees and turn it up on to the front side, so that the back of the printer is facing up and the bottom facing you.

  • Be careful because the feed roller assembly is now loose, but it is still attached to the main body of the printer.

  • Push in the tab on the left side of the back panel and pull outward to remove the back panel.

Schritt 9  ¶ 

Tilt the printer up until the bottom of the printer can be seen. Remove the T10 12mm Torx screw from the bottom panel. Grasp the top edge of the bottom panel and pull to remove it.

Schritt 9  ¶ 

  • Tilt the printer up until the bottom of the printer can be seen.

  • Remove the T10 12mm Torx screw from the bottom panel.

  • Grasp the top edge of the bottom panel and pull to remove it.

Schritt 10  ¶ 

Remove the black plastic cross member from the bottom of the printer. Remove the black plastic cross member from the bottom of the printer.

Schritt 10  ¶ 

  • Remove the black plastic cross member from the bottom of the printer.

Schritt 11  ¶ 

Turn the printer back down so that it is sitting on the bottom panel and rotate the printer 180 degrees.

Schritt 11  ¶ 

  • Turn the printer back down so that it is sitting on the bottom panel and rotate the printer 180 degrees.

Schritt 12  ¶ 

Remove the printer head cleaner by lifting the front of the printer head cleaner above the track and slide it forward. This is an extremely difficult step. It can take quite a bit of force to lift the printer head cleaner above the track and it is easy to slip and hurt yourself. This is an extremely difficult step. It can take quite a bit of force to lift the printer head cleaner above the track and it is easy to slip and hurt yourself.

Schritt 12  ¶ 

  • Remove the printer head cleaner by lifting the front of the printer head cleaner above the track and slide it forward.

  • This is an extremely difficult step. It can take quite a bit of force to lift the printer head cleaner above the track and it is easy to slip and hurt yourself.

Schritt 13  ¶ 

This step can be performed with out rotating the printer, but we have rotated the printer for clarity. Grasp the left side of the feed roller assembly and pull towards the front of the printer and up to free the metal tab from the slot. Grasp the left side of the feed roller assembly and pull towards the front of the printer and up to free the metal tab from the slot.

Schritt 13  ¶ 

  • This step can be performed with out rotating the printer, but we have rotated the printer for clarity.

  • Grasp the left side of the feed roller assembly and pull towards the front of the printer and up to free the metal tab from the slot.

Schritt 14  ¶ 

Lift the feed roller assembly straight up to remove it.

Schritt 14  ¶ 

  • Lift the feed roller assembly straight up to remove it.