Zum Hauptinhalt wechseln
Hilfe

MacBook Pro 15" Retina Display Mid 2012 Display Assembly Replacement

Empfohlene Anleitung

Empfohlene Anleitung

Diese Anleitung wird von den iFixit-Mitarbeitern als außergewöhnlich gut eingestuft.

Replace the display assembly in your MacBook Pro 15" Retina Display Mid 2012.

  • Autor: Jake Devincenzi
  • Geschätzte Zeit: 1 Stunde
  • Schwierigkeitsgrad: Moderat

Did your display assembly have an unfortunate encounter with a hard surface? Use this guide to replace it.

Schritt 1 Display Assembly  ¶ 

Use the flat end of a spudger to pry off the two rubber hinge covers, one from each end of the device. Use the flat end of a spudger to pry off the two rubber hinge covers, one from each end of the device.

Schritt 1 Display Assembly  ¶ 

  • Use the flat end of a spudger to pry off the two rubber hinge covers, one from each end of the device.

Schritt 2  ¶ 

Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge covers to the upper case. Remove the two aluminum hinge brackets from the MacBook Pro.

Schritt 2  ¶ 

  • Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge covers to the upper case.

  • Remove the two aluminum hinge brackets from the MacBook Pro.

Schritt 3  ¶ 

Use the tip of a spudger to pry the display data cable lock and rotate it toward the DC-In side of the computer. Pull the display data cable straight out of its socket on the logic board. Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

Schritt 3  ¶ 

  • Use the tip of a spudger to pry the display data cable lock and rotate it toward the DC-In side of the computer.

  • Pull the display data cable straight out of its socket on the logic board.

  • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

Schritt 4  ¶ 

Remove four out of the six 5.3 mm T8 Torx screws securing the display to the upper case.

Schritt 4  ¶ 

  • Remove four out of the six 5.3 mm T8 Torx screws securing the display to the upper case.

  • We purposely have you leave one screw attaching the display to the upper case to aid in future steps.

  • When reassembling, make sure that the screws go through the two grounding loops on the webcam/airport cable.

Schritt 5  ¶ 

Open the MacBook Pro approximately 110 degrees, and place it sideways on the table, as shown.

Schritt 5  ¶ 

  • Open the MacBook Pro approximately 110 degrees, and place it sideways on the table, as shown.

  • While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the lower (closer to the table) display bracket.

Schritt 6  ¶ 

Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

Schritt 6  ¶ 

  • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

  • While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the upper display bracket.

Schritt 7  ¶ 

Grip both halves of the device, one in each hand. Gently push forward on the bottom half of the device to detach it from the display assembly. Carefully set each component aside, making sure to set down the lower half keyboard-side down.

Schritt 7  ¶ 

  • Grip both halves of the device, one in each hand.

  • Gently push forward on the bottom half of the device to detach it from the display assembly.

  • Carefully set each component aside, making sure to set down the lower half keyboard-side down.