Repariere deine Sachen Community Store

Vierte iPhone Generation. Die Reparatur an sich ist unkompliziert, aber Frontglas und LCD müssen gemeinsam ersetzt werden. GSM mit 8, 16 oder 32 GB Kapazität, Modell A1332 in schwarz und weiß.

2375 Fragen Alle anzeigen

Einstellungen

How to remove a stripped screw from near the vibrator motor?

Whilst trying to disassemble my Iphone 4G to replace the Digitizer & LCD screen i have managed to find and probally strip a tiny screw.

This screw is located near the Vibrator motor just above where the battery sits.

I have tried using a flat rubber band to give grip and even a larger screwdriver with pressure to create it after listening to suggestions - neither of these ideas have worked! what can i do? i've heard that a dab of superglue on the screw head and setting a screwdriver to it should work? is this true would it help or is there something else i can do to get the screw out.

please it is urgent as i need my phone.

Diese Frage beantworten Ich habe das gleiche Problem

Ist dies eine gute Frage?

Ja Nein
Bewertung -1
1 Kommentar

I haven't gotten a new screw but I've just ordered a new vibrate motor as the connection without the screw isn't strong enough to activate the vibrate all the time. So replacing the whole thing since I bent the bracket :-)

Thanks again for the help

von

Einen Kommentar hinzufügen

2 Antworten

Filtern nach:
Am hilfreichsten Neueste Älteste
Hilfreichste Antwort

Einstellungen

I would try the superglue trick since it seems you are in a hurry. Use a small phillips screwdriver and a drop of more thick running glue. Do not use the type that flows smoothly or you could end up gluing even more than you want.

Here is some advice: http://www.todayifoundout.com/index.php/...

Take your time and move slowly. A Dremel could be your rescue but be careful so you don't damage more.

War diese Antwort hilfreich?

Ja Nein
Bewertung 2

4 Kommentare:

Camera screws are similar. Here may be some help: http://www.ehow.com/how_5718712_remove-s...

von

I drill them out..very carefully! works for me.

von

Thanx for the suggestions the glue didn't work

And I was too scared to drill it out.

I ended up using tweezers n bending the bracket to be able to access the screw for the new LCD n digitizer and when I pushed the bracket back into place the screw just popped out ( go figure)

My phones all back together now n functioning fine :-)

von

Did you get a new screw or just leave it? Kudos to you for not giving up Jeannie ;-)

von

Einen Kommentar hinzufügen

Einstellungen

You can try this but i must warn you to be VERY CAUTIOUS in what you are doing. I used this method and it was successful for me, but then again, it was a small screw. *I am not responsible for any damage done to your phone* :)

Ok, so i took a power drill and used it on the top screw of the EMF protection shield. The screw was stripped so I took the smallest drill bit i could find that would just fit the circumference of the screw. Then, very carefully screw into it, completely making the screw into a bowl. Next, switched directions of the drill, used a little force and went slow....next thing i know the screw is out. You can try this but just be careful and don't break anything. GOOD LUCK! Let me Know if you need anything else. PLEASE be careful

War diese Antwort hilfreich?

Ja Nein
Bewertung 0
Einen Kommentar hinzufügen

Antwort hinzufügen

Jeannie wird auf ewig dankbar sein.
Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 2,589