⟐ Answered März 19, 2026 at 4:42 GMT-7

Wir haben Adora s v-vzuG.

Anzeige ...grosse Unwucht beim Schleudern ...und ..es pumpt nicht mehr ab. Zuerst angezeigt Ablaufschlauch prüfen. Jetzt nur noch durch vorerst entleeren Schleudern möglich.

Ist jetzt Pumpe defekt und Entkalkung nötig?

Besten ydank

Felix Müller

⟐ Answered Januar 01, 2026 at 10:24 GMT-7

⟐ Answer accepted Dezember 31, 2025 at 15:32 GMT-7

⟐ Commented September 29, 2025 at 11:42 GMT-7

Waschmaschine ist eine Siemens iQ 300

Es liegt nicht an der Wäsche. Habe ich auch schon gedacht aber es wäre hier nichts mit Knöpfen dabei gewesen und das Geräusch kommt auch bei anderer Wäsche.

https://youtube.com/shorts/5UIDHx2o4ng?s...

⟐ Commented August 14, 2025 at 5:19 GMT-7

Nun verzweifele Ich aber an dem Lager des Motors

.

Die Welle, auf die der bürstenlose Motor gesteckt wird, hat ein M8 Gewinde für die sichernde Schraube. Ich habe schon versucht mit einer Gewindestange und einem schweren Gegenstand das Lager auszutreiben. Ich habe leider keinen so winzigen Abzieher, den man nur auf das Gehäuse des Lagers ansetzen kann.

Auch kann man nicht den seitlichen Kunststoffdeckel der Trommel (der ist verschraubt und verklippt) abhebeln, da scheinbar in der Mitte, wo das Lager sitzt blockiert

Weiß jemand wie das konstruiert sein könnte?

Ich will den Deckel auch in jedem Fall demontieren, weil ich die Dichtung reinigen möchte. Die ist durch Kalkfraß leicht undicht geworden (rostige Schrauben am Trommelboden).

⟐ Answered November 18, 2024 at 16:47 GMT-7

⟐ Answered Juni 15, 2024 at 5:19 GMT-7

++++

Hallo!

Ich habe einen LG direct drive (8kg) Waschtrockner.

Der Motor schlägt im Betrieb auf die Waschtrommel, weil die Schrauben nicht mehr halten. Die vorgebohrten Löcher sind im Eimer. Sowohl bei einer Metallplatte und dem Plastikgebilde, auf die der Motor geschraubt sein sollte.

Ich finde/ habe die korrekte Modellnummer nicht.

FRAGE: Wie heißen diese Teile und wo kann ich Ersatzteile bestellen?

Die Maschine lief vorher astrein. Wäre Verschwendung, sie nicht zu reparieren.

Freue mich auf Rückmeldung!

Liebe Grüße

_______________________________________

Hello!

I have an LG direct drive (8kg) washer-dryer.

The motor is hitting the drum during operation because the screws no longer hold. The pre-drilled holes are worn out. This is happening with both a metal plate and the plastic structure where the motor should be screwed onto.

I can't seem to find or have the correct model number.

QUESTION: What are these parts called and where can I order replacement parts?

The machine was working perfectly before. It would be a shame not to repair it.

Looking forward to your response!

⟐ Commented August 21, 2023 at 21:14 GMT-7

⟐ Answer accepted Juni 12, 2020 at 13:58 GMT-7

Meine Waschmaschine füllt sich zwar mit Wasser, aber sie pumpt nicht mehr von selbst ab und schleudert auch nicht. Ich kann das Wasser nur manuell ablaufen lassen, indem ich den Schlauch nach unten halte.

⟐ Edited by author Juli 17, 2019 at 2:14 GMT-7

⟐ Commented Mai 17, 2026 at 4:49 GMT-7

After a power outage, I wanted to continue the washing cycle. The washing machine would not start. I reset the program by holding the START button for a long time. The washing machine lit up all the LEDs. Then they turned off and nothing happened.

Exactly 20 minutes later, the pump starts running and the LOCK LED begins flashing rapidly, while the RAPID WASH LED flashes a little more slowly. After 5 minutes, the pump stops, but the LED combination keeps flashing in the same way.

There should be two hidden diagnostic LEDs on the inside of the control panel. They are not flashing.

The door lock is working — verified.
The motor works.
The heating element works.
The pressure switch works.
The pump works.

I measured continuity with resistance at the output of the temperature sensor.
The tacho generates voltage according to motor speed when the motor is turning.
The relays on the control board are functional.

Everything was tested outside the washing machine wiring.
The electrolytic capacitors have been replaced.
The triac controlling the door lock is fine and was replaced just in case.

What seems strange, however, is that the door lock engages almost immediately after the washing machine is plugged into the mains. This happens because the processor’s control pin sends a signal to the base of the transistor that triggers the triac.The door lock unlocks only if I unplug the washing machine from the mains.

thank you

⟐ Commented Mai 16, 2026 at 7:16 GMT-7

⟐ Commented Mai 16, 2026 at 1:10 GMT-7

Model : GTW490ACJ6WS

Serial TS973434G

I need know what personality it comes in I got one off fb and I think personality manufacture is off and what ther software is on for test 3,4,5 is on plz

⟐ Edited Mai 16, 2026 at 0:09 GMT-7

⟐ Commented Mai 15, 2026 at 7:24 GMT-7

My washing machine has an issue where it pours water during the spin cycle, while it is draining. Basically, it pours water from the top while draining it out from the bottom. It drains the water faster than it can pour it, so it does not actually fill with water, but it does re-wet the clothes, so the clothes are dripping wet when the cycle is complete.

It also agitates while filling with water. This is not much of a problem, but it started happening the same time that the other issue above started happening.

Model: Kenmore Elite 26964503

This is what the washing machine is supposed to do:

1. Wash Cycle
   1. Fill with water.
   2. When full, begin agitating.
   3. After a while, drain water.
2. Rinse Cycle
   1. Fill with water.
   2. When full, begin agitating.
   3. After a while, drain water.
3. Spin Cycle
   1. Spin while draining water.
   2. When empty, continue spinning and draining.
   3. After a while, stop.

This is what the washing machine actually does (the bold text marks the differences):

1. Wash Cycle
   1. Fill with water while agitating.
   2. When full, continue agitating.
   3. After a while, drain water.
2. Rinse Cycle
   1. Fill with water while agitating.
   2. When full, continue agitating.
   3. After a while, drain water.
3. Spin Cycle
   1. Spin while draining water.
   2. When empty, continue spinning and draining but also begin pouring water from top.
   3. After a while, stop.

The main problem is 3-2: in the spin cycle, the machine begins to pour water after it has drained all of the water. It is not supposed to be pouring water at this point; it defeats the purpose of the spin cycle.

What could this be? What would cause it to pour water during the spin cycle?

⟐ Commented Mai 14, 2026 at 17:56 GMT-7

Frigidaire Affinity FAHE1011MWO

⟐ Commented Mai 12, 2026 at 14:57 GMT-7

⟐ Commented Mai 10, 2026 at 9:34 GMT-7

⟐ Answered Mai 10, 2026 at 8:08 GMT-7