iFixit - Answers With Device "Washing Machine"

Bauknecht WAT Sensitive 32DI: Dryer is not working

Thu, 28 May 2026 07:00:37 -0700

My dryer is not working

Midea Washing Machine: Why is my Midea Twin Tube washer's spin - dryer not working?

Mon, 25 May 2026 08:04:56 -0700

My 1 year old, 15 kg Midea Twin Tube washing machine keeps washing clothes, but the separate spin - dryer part stopped working. I can still hear (a motor?) humming, it drains, but doesn't spin.

⟐ Commented Mai 25, 2026 at 8:04 GMT-7

Washing Machine: UniMac UY55 Keypad Trouble

Sun, 24 May 2026 04:46:27 -0700

I have a UniMac Model UY55 washer. I replaced the CPU board and downloaded the new firmware onto the machine. I am trying to navigate on the keypad to finish the setup. The number keypad is responsive but some of the arrow buttons are not. I rechecked all connections on the CPU board twice. I reseated the ribbon cable to the CPU board several times. I did not clean the female ribbon cable connector coming from the keypad. Not sure how to diagnose and or clean. Not sure what made the CPU board go out. Maybe whatever it was may have taken the keypad out also? Any advice would be appreciated!! Thanks

Washing Machine: Full service For Godrej washing machine - I wash

Fri, 22 May 2026 02:14:19 -0700

How to make a home made lint filter

⟐ Commented Mai 22, 2026 at 2:14 GMT-7

Indesit Washing Machine: Once I click on play the drum won't roll and all leds will blinks

Mon, 18 May 2026 23:24:21 -0700

Drum refuses to roll

GE Washing Machine: GE washing cycle not turning

Sun, 10 May 2026 09:34:14 -0700

Agitator not turning on washing cycle

⟐ Commented Mai 10, 2026 at 9:34 GMT-7

Giantex Washing Machine: الغساله لا تفوت الماء بقوه

Sat, 09 May 2026 02:44:14 -0700

الماء لايمر قوي

Whirlpool Washing Machine: F9E1 whirlpool washer won't drain FIXED

Sun, 03 May 2026 15:19:17 -0700

UPDATE: NO POLARITY. CONNECT THE WIRES HOWEVER YOU WANT. Wtw5100hw0 wouldn't drain, so I checked the hose for clogs. Checked the plug for continuity and nothing. I found a break in the wire so I fixed that. Check continuity and nothing, I cut the connector off and both wires have continuity. Now the problem is I can't find the connector I cut off. I have female spade connectors on the wires but have no idea which wire goes to what terminal on the pump.

⟐ Edited by author Mai 03, 2026 at 15:19 GMT-7

Midea Washing Machine: Why is the washing machine run sheking

Sat, 02 May 2026 06:17:08 -0700

Why is the washing machine run sheking

⟐ Commented Mai 02, 2026 at 6:17 GMT-7

Washing Machine: I have a glanced fully automatic washing machine that’s starting to ha

Fri, 01 May 2026 21:48:51 -0700

My washing machine is starting to slip during agitation

⟐ Commented Mai 01, 2026 at 21:48 GMT-7

Washing Machine: Error code F08 - Troubleshoot

Tue, 28 Apr 2026 06:40:39 -0700

I’m troubleshooting my Whirlpool FWG8168BV that’s throwing an F08 error code, and I’d really appreciate some input.

Initial behavior:

- On a 30°C cycle, the machine starts normally (fills with water, drum rotates both directions).

- After about 10 minutes, it stops, drains itself, and shows F08.

Current behavior:

- Now it throws the F08 error immediately when starting a wash.

What I’ve checked so far:

- Heating element: Resistance measures within expected range. Removed and inspected, no visible damage. Also powered it directly and it heats up quickly.

- NTC sensor: Resistance changes correctly with temperature, seems functional.

- Voltage at heating element: Measured during a 30°C cycle, reads 0V.

- Relays (on PCB): Tested off-board with 9V, confirmed they click and switch correctly.

Where I’m stuck:

- I’m not sure how to verify if the relays are actually receiving the control/drive voltage during operation.

- Could the issue be upstream (control board logic)?

- Is it possible the pressure switch is not signaling correct water level, preventing heating?

Has anyone seen a similar issue or can point me in the right direction for further diagnostics?

Thanks in advance!

Crosley Washing Machine: no power to my crosley washing machine no matter what I try

Mon, 27 Apr 2026 17:53:41 -0700

I can't get no power to my crosley washing machine no matter what I try and the lid is locked so what could be the problem

⟐ Commented April 27, 2026 at 17:53 GMT-7

Fisher and Paykel CleanSmart Washing Machine WL1068P1: Why the lid cannot lock?

Fri, 24 Apr 2026 18:39:03 -0700

I want to spin but it cant. The machine is showing lid failure

GE Washing Machine: washing machine absolutely losing its mind

Wed, 22 Apr 2026 00:31:55 -0700

ge top-load washing machine. unsure of exact model of washer or purchase year since its my aunts and not my own

did not start until someone started spinning the drum a bit manually before hitting the start button
would not respond to any button inputs until then, stopped responding to button inputs after
keeps chiming and activating/deactivating buttons seemingly at random (deep fill and my cycle in particular) which i have video footage of here -- please excuse the subpar quality
to my knowledge no settings have been changed in any way, intentionally or otherwise, that could cause this
as far as my testing can confirm its not an issue with load size, balance, or power
worked just fine up until sometime yesterday at earliest

what gives? is it just a big fancy block of garbage now? thanks in advance for any answers you may have o7

⟐ Commented April 22, 2026 at 0:31 GMT-7

Amana Washing Machine NTW4516FW: Macine Not agitating properley

Sun, 19 Apr 2026 12:42:59 -0700

The dogs on the top are in good shape but it is not agitating

Maytag or Whirlpool Centennial washer: Leak when spin drying

Sun, 19 Apr 2026 08:38:34 -0700

My washing machine will leak when spin drying

Kenmore 90 Series Washing Machine: Washer hums after filling, will not agitate, spin, or drain

Sat, 18 Apr 2026 16:13:09 -0700

I have a Kenmore 90 Series washer. Last week it began making a humming sound after filling. It will not agitate, spin, or drain.

I was able to empty it out and check the pump, didn't find any issues but replaced anyways. Issue persisted. Lid latch working normally as well. I can manually rotate the barrel from inside the washer and by spinning the coupler on the motor side of the transmission.

Removed the motor and verified the coupling was still intact, and did not notice any mushrooming or smell from the capacitor. I noticed the motor was very hot, but I am unsure if it was outside normal parameters. I also noticed a few wires getting very hot from inside the cabinet.

⟐ Edited by author April 18, 2026 at 16:13 GMT-7

Blomberg Washing Machine: Noise from the rubber

Thu, 16 Apr 2026 20:19:21 -0700

When i look inside the machine it seems off centric. Could it be that the drum spider is bent and need to be replaced?

Samsung Washing Machine WA49B5105AW: machine automatic drain water after few minutes of filling

Wed, 15 Apr 2026 03:05:46 -0700

machine automatic drain water after few minutes of filling

Washing Machine: doesnt fill up with water

Tue, 14 Apr 2026 01:17:55 -0700

it just keeps running water but never fills at all

⟐ Commented April 14, 2026 at 1:17 GMT-7