Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Store

Hilfe

Aktuelle Version von: oldturkey03 ,

Text:

Mountaineer, I'd be starting at the tank and see what is going on. Start with the fuel $!^&valve on the tank
Mountaineer, I'd be starting at the tank and see what is going on. Start with the fuel $!^&valve on the tank
 
CHECKING THE FUEL $!^&Valve
CHECKING THE FUEL $!^&Valve
 
1. Check:

fuel $!^&
fuel valve

fuel $!^&
fuel valve
Cracks/damage/wear ==> Replace.
 
2. Check:

fuel $!^&
fuel valve strainer 1

fuel $!^&
fuel valve strainer 1
obstruction ==> clean.
 
Blow out the jets with compressed air.
 
Damage ==> Replace.
 
You also mentioned that you "clean carb float area" I would suggest that you check the valve to make sure it is not stuck and check the fuel level:
 
MEASURING AND ADJUSTING THE FUEL LEVEL
 
1. Measure:
 
fuel level a
 
Out of specification ==> Adjust.
 
Fuel level (below the float chamber mating surface)
 
6.5 ~ 7.5 mm (0.26 ~ 0.30 in)
 
a. Stand the motorcycle on a level surface.
 
b. Place the motorcycle on a suitable stand to ensure that the motorcycle is standing straight up.
 
c. Install the fuel level gauge 1 onto the fuel drain pipe 2
 
d. Loosen the fuel drain screw
 
e. Hold the fuel level gauge vertically next to the float chamber 3.
 
f. Measure the fuel level a.
 
[image|656267]
 
2. Adjust:
 
fuel level
 
a. Remove the carburetor.
 
b. Check the needle valve seat and needle valve.
 
c. If either is worn, replace them as a set.
 
d. If both are fine, adjust the float level by slightly bending the float tang 1.
 
e. Install the carburetor.
 
f. Measure the fuel level a again.
 
g. Repeat steps (a) to (f) until the fuel level is within specification.

Status:

open

Ursprünglicher Beitrag von: oldturkey03 ,

Text:

Mountaineer, I'd be starting at the tank and see what is going on. Start with the fuel $!^&

CHECKING THE FUEL $!^&

1. Check:

fuel $!^&

Cracks/damage/wear ==> Replace.

2. Check:

fuel $!^& strainer 1

obstruction ==> clean.

Blow out the jets with compressed air.

Damage ==> Replace.

You also mentioned that you "clean carb float area" I would suggest that you check the valve to make sure it is not stuck  and check the fuel level:

MEASURING AND ADJUSTING THE FUEL LEVEL

1. Measure:

fuel level a

Out of specification ==> Adjust.

Fuel level (below the float chamber mating surface)

6.5 ~ 7.5 mm (0.26 ~ 0.30 in)

a. Stand the motorcycle on a level surface.

b. Place the motorcycle on a suitable stand to ensure that the motorcycle is standing straight up.

c. Install the fuel level gauge 1 onto the fuel drain pipe 2

d. Loosen the fuel drain screw

e. Hold the fuel level gauge vertically next to the float chamber 3.

f. Measure the fuel level a.

[image|656267]

2. Adjust:

fuel level

a. Remove the carburetor.

b. Check the needle valve seat and needle valve.

c. If either is worn, replace them as a set.

d. If both are fine, adjust the float level by slightly bending the float tang 1.

e. Install the carburetor.

f. Measure the fuel level a again.

g. Repeat steps (a) to (f) until the fuel level is within specification.

Status:

open