Zum Hauptinhalt wechseln
Hilfe

Aktuelle Version von: arsdezi ,

Text:

'''Ok, problem for this case has been found and we have solution!'''
 
If your Jabra Move headphones not produce sound in left channel in wireless mode - that's bad switching contact in jack connector!
 
'''For checking if that your problem and solution too you must try to bend and close contact by hand for left channel pin!'''
 
[image|868235]
 
This is jack have 7 pins (has 3 switching contacts for switching mode with cable/without cable)
 
Connector was found as ''3.5mm Female Audio Connector 7 Pin SMD Stereo Headphone Jack'' or same ''smd 7 pin earphone socket jack'' and I found '''Model number: PJ-382-7P''':
 
[image|868237]
 
[image|868236]
 
You can buy it on the links
 
# http://www.aliexpress.com/item/10pcs-Phone-Jack-Diameter-3-5mm-7-pin-audio-socket-for-4-poles-earphone-plug-SMD/32648604057.html
# http://www.aliexpress.com/item/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392/32596449477.html
# http://www.ebay.com/itm/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392-/121487523477
 
For the disassemble JABRA MOVE headphones please read post by Muro, thank you @mrmuro ;) :
 
''To dissasemble you don't need to unscrew anything, you just have to get the back part of the speaker in one hand and the other part(the one with earspillow) in the other and rotate the second one counter clockwise. If you put the right force you will feel a click and the headphones will be dissasembled.It's not so easy, but normally it could be done without breaking the headphones.''
 
'''For easy untwisting and for disassembly of the headphones cups you can is not removing ear pillows before untwisting, and tightly hold by hand via pillow. But be very careful to avoid damaging of the ear pillows! To better understand the direction of untwisting, see picture:'''
 
[image|868234]
 
Headphones and cups have the three elements of simple mechanical lock:
 
[image|868238]
 
BTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist!
BTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist!
 
'''Important UPDATE:
For me not helped a good flux and desoldering ribbon - for quality soldering you must have the soldering-iron with hot air tip! And unfortunately some contact tracks has been detached when I tried to desoldering of the connector( Because soldering from manufacturer has high-temperature solder!'''
 
Good luck!
 
Thank you all for your help!
 
Good luck!
 
''PS: apologies again for my bad English!''

Status:

open

Bearbeitet von: arsdezi ,

Text:

'''Ok, problem for this case has been found and we have solution!'''
 
If your Jabra Move headphones not produce sound in left channel in wireless mode - that's bad switching contact in jack connector!
 
'''For checking if that your problem and solution too you must try to bend and close contact by hand for left channel pin!'''
 
[image|868235]
 
This is jack have 7 pins (has 3 switching contacts for switching mode with cable/without cable)
 
Connector was found as ''3.5mm Female Audio Connector 7 Pin SMD Stereo Headphone Jack'' or same ''smd 7 pin earphone socket jack'' and I found '''Model number: PJ-382-7P''':
 
[image|868237]
 
[image|868236]
 
You can buy it on the links
 
# http://www.aliexpress.com/item/10pcs-Phone-Jack-Diameter-3-5mm-7-pin-audio-socket-for-4-poles-earphone-plug-SMD/32648604057.html
# http://www.aliexpress.com/item/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392/32596449477.html
# http://www.ebay.com/itm/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392-/121487523477
 
For the disassemble JABRA MOVE headphones please read post by Muro, thank you @mrmuro ;) :
 
''To dissasemble you don't need to unscrew anything, you just have to get the back part of the speaker in one hand and the other part(the one with earspillow) in the other and rotate the second one counter clockwise. If you put the right force you will feel a click and the headphones will be dissasembled.It's not so easy, but normally it could be done without breaking the headphones.''
 
'''For easy untwisting and for disassembly of the headphones cups you can is not removing ear pillows before untwisting, and tightly hold by hand via pillow. But be very careful to avoid damaging of the ear pillows! To better understand the direction of untwisting, see picture:'''
 
[image|868234]
 
Headphones and cups have the three elements of simple mechanical lock:
 
[image|868238]
 
'''BTWBTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist! '''

'''Important UPDATE:
For me not helped a good flux and desoldering ribbon - for quality soldering you must have the soldering-iron with hot air tip! And unfortunately some contact tracks has been detached when I tried to desoldering of the connector( Because soldering from manufacturer has high-temperature solder!'''

Good luck!
'''BTWBTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist! '''

'''Important UPDATE:
For me not helped a good flux and desoldering ribbon - for quality soldering you must have the soldering-iron with hot air tip! And unfortunately some contact tracks has been detached when I tried to desoldering of the connector( Because soldering from manufacturer has high-temperature solder!'''

Good luck!
 
Thank you all for your help!
 
Good luck!
 
''PS: apologies again for my bad English!''

Status:

open

Bearbeitet von: arsdezi ,

Text:

'''Ok, problem for this case has been found and we have solution!'''
 
If your Jabra Move headphones not produce sound in left channel in wireless mode - that's bad switching contact in jack connector!
 
'''For checking if that your problem and solution too you must try to bend and close contact by hand for left channel pin!'''
 
[image|868235]
 
This is jack have 7 pins (has 3 switching contacts for switching mode with cable/without cable)
 
Connector was found as ''3.5mm Female Audio Connector 7 Pin SMD Stereo Headphone Jack'' or same ''smd 7 pin earphone socket jack'' and I found '''Model number: PJ-382-7P''':
 
[image|868237]
 
[image|868236]
 
You can buy it on the links
 
# http://www.aliexpress.com/item/10pcs-Phone-Jack-Diameter-3-5mm-7-pin-audio-socket-for-4-poles-earphone-plug-SMD/32648604057.html
# http://www.aliexpress.com/item/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392/32596449477.html
# http://www.ebay.com/itm/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392-/121487523477
 
For the disassemble JABRA MOVE headphones please read post by Muro, thank you @mrmuro ;) :
 
''To dissasemble you don't need to unscrew anything, you just have to get the back part of the speaker in one hand and the other part(the one with earspillow) in the other and rotate the second one counter clockwise. If you put the right force you will feel a click and the headphones will be dissasembled.It's not so easy, but normally it could be done without breaking the headphones.''
 
I think'''For easy untwisting and for disassembly of the headphones cups you must remove thecan is not removing ear pillows before to untwisting, and tightly hold by hand via pillow. But be very careful to avoid damaging them! Better to wrap cloth to avoid slipping cup when you will untwist fromof the headphonesear pillows! To better understand the direction of untwisting, see picture:picture:'''
I think'''For easy untwisting and for disassembly of the headphones cups you must remove thecan is not removing ear pillows before to untwisting, and tightly hold by hand via pillow. But be very careful to avoid damaging them! Better to wrap cloth to avoid slipping cup when you will untwist fromof the headphonesear pillows! To better understand the direction of untwisting, see picture:picture:'''
[image|868234]
 
Headphones and cups have the three elements of simple mechanical lock:
 
[image|868238]
 
'''BTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist! '''
 
Thank you all for your help!
 
Good luck!
 
''PS: apologies again for my bad English!''

Status:

open

Bearbeitet von: arsdezi ,

Text:

Ok'''Ok, problem for this case has been found and we have solution!solution!'''
Ok'''Ok, problem for this case has been found and we have solution!solution!'''
 
If your Jabra Move headphones not produce sound in left channel in wireless mode - that's bad switching contact in jack connector!
 
'''For checking if that your problem and solution too you must try to bend and close contact by hand for left channel pin!'''
 
[image|868235]
 
This is jack have 7 pins (has 3 switching contacts for switching mode with cable/without cable)
 
Connector was found as ''3.5mm Female Audio Connector 7 Pin SMD Stereo Headphone Jack'' or same ''smd 7 pin earphone socket jack'' and I found '''Model number: PJ-382-7P''':
 
[image|868237]
 
[image|868236]
 
You can buy it on the links
 
# http://www.aliexpress.com/item/10pcs-Phone-Jack-Diameter-3-5mm-7-pin-audio-socket-for-4-poles-earphone-plug-SMD/32648604057.html
# http://www.aliexpress.com/item/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392/32596449477.html
# http://www.ebay.com/itm/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392-/121487523477
 
For the disassemble JABRA MOVE headphones please read post by Muro, thank you ;@mrmuro ;) :
For the disassemble JABRA MOVE headphones please read post by Muro, thank you ;@mrmuro ;) :
 
''To dissasemble you don't need to unscrew anything, you just have to get the back part of the speaker in one hand and the other part(the one with earspillow) in the other and rotate the second one counter clockwise. If you put the right force you will feel a click and the headphones will be dissasembled.It's not so easy, but normally it could be done without breaking the headphones.''
 
I think you must remove the ear pillows before to untwisting, to avoid damaging them! Better to wrap cloth to avoid slipping cup when you will untwist from the headphones!

to
To better understand the direction of untwisting, see picture!
picture:
I think you must remove the ear pillows before to untwisting, to avoid damaging them! Better to wrap cloth to avoid slipping cup when you will untwist from the headphones!

to
To better understand the direction of untwisting, see picture!
picture:
[image|868234]
 
Headphones and cups have the three elements of simple mechanical lock:
 
[image|868238]

'''By the way
'''BTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist! '''

'''By the way
'''BTW, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist! '''
 
Thank you all for your help!
 
Good luck!
 
PS''PS: apologies again for my bad English!English!''
PS''PS: apologies again for my bad English!English!''

Status:

open

Ursprünglicher Beitrag von: arsdezi ,

Text:

Ok, problem for this case  has been found and we have solution!

If your Jabra Move headphones not produce sound in left channel in wireless mode - that's bad switching contact in jack connector!

'''For checking if that your problem and solution too you must try to bend and close contact by hand for left channel pin!'''

[image|868235]

This is jack have 7 pins (has 3 switching contacts for switching mode with cable/without cable)

Connector was found as ''3.5mm Female Audio Connector 7 Pin SMD Stereo Headphone Jack'' or same ''smd 7 pin earphone socket jack'' and I found '''Model number: PJ-382-7P''':

[image|868237]

[image|868236]

You can buy it on the links

# http://www.aliexpress.com/item/10pcs-Phone-Jack-Diameter-3-5mm-7-pin-audio-socket-for-4-poles-earphone-plug-SMD/32648604057.html
# http://www.aliexpress.com/item/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392/32596449477.html 
# http://www.ebay.com/itm/20Pcs-3-5mm-Female-Audio-Connector-7-Pin-SMT-SMD-Stereo-Headphone-Jack-PJ-392-/121487523477 

For the disassemble JABRA MOVE headphones please read post by Muro, thank you ;) :

''To dissasemble you don't need to unscrew anything, you just have to get the back part of the speaker in one hand and the other part(the one with earspillow) in the other and rotate the second one counter clockwise. If you put the right force you will feel a click and the headphones will be dissasembled.It's not so easy, but normally it could be done without breaking the headphones.''

I think you must remove the ear pillows before to untwisting, to avoid damaging them! Better to wrap cloth to avoid slipping cup when you will untwist from the headphones!

to better understand the direction of untwisting, see picture!

[image|868234]

Headphones and cups have the three elements of simple mechanical lock:

[image|868238]

'''By the way, for replace jack connector (it has SMD/SMT type) you must be able to work with surface mount soldering, so as not to damage the board! That Is not difficult, for this you must have: a soldering iron with a small tip, good quality flux, solder, and desoldering ribbon. Or better take help for such work from specialist! '''

Thank you all for your help!

Good luck!

PS: apologies again for my bad English!

Status:

open