Zum Hauptinhalt wechseln
Hilfe

Aktuelle Version von: No Einstein ,

Titel:

Kenmore Elite HE5t washing machine F32 and F99 Error Codes

Text:

The washer was giving SUD/F35 error.  I installed a new CCU and a new Pressure Switch. It immediately gave F32 error at about 7 minutes of starting the wash.  If I pull the plug and restart (so that the door will unlock), it gives F99, which goes away if I hit the power button, but F32 comes back in about 7 minutes of starting the wash.  I also checked the voltage on PS8 socket pin 1 and 2, and it shows 0.5V when the tub is empty, and when it starts filling, it slowly rises to 3.0V, and then I get F32 error.
The fill, spin, drain seem to work just fine.  I checked the pressure sensor tube at the top and it seems fine (although did not check the bottom, as it would require moving the machine).  I cleaned the filter to the drain-pump, and checked the pump for any debris.
-When I run the diagnosis, it immediately gives F99 error and stops. What do you think is the issue? Thanks for your help.
+When I run the diagnosis option 1, it immediately gives F99 error and stops. If I run the Diagnosis Only test (option #2), it cycles through C00 to C04, spends a long time on C04, and then throws F32.
+
+What do you think is the issue? Thanks for your help.

Gerät:

Kenmore Washer

Status:

open

Duplikat von:

706844

Bearbeitet von: jayeff (Bewertungsdetails) ,

Titel:

Kenmore Elite HE5t washing machine F32 and F99 Error Codes

Text:

The washer was giving SUD/F35 error.  I installed a new CCU and a new Pressure Switch. It immediately gave F32 error at about 7 minutes of starting the wash.  If I pull the plug and restart (so that the door will unlock), it gives F99, which goes away if I hit the power button, but F32 comes back in about 7 minutes of starting the wash.  I also checked the voltage on PS8 socket pin 1 and 2, and it shows 0.5V when the tub is empty, and when it starts filling, it slowly rises to 3.0V, and then I get F32 error.

The fill, spin, drain seem to work just fine.  I checked the pressure sensor tube at the top and it seems fine (although did not check the bottom, as it would require moving the machine).  I cleaned the filter to the drain-pump, and checked the pump for any debris.

When I run the diagnosis, it immediately gives F99 error and stops. What do you think is the issue? Thanks for your help.

Gerät:

Kenmore Washer

Status:

open

Duplikat von:

+706844

Ursprünglicher Beitrag von: No Einstein ,

Titel:

Kenmore Elite HE5t washing machine F32 and F99 Error Codes

Text:

The washer was giving SUD/F35 error.  I installed a new CCU and a new Pressure Switch. It immediately gave F32 error at about 7 minutes of starting the wash.  If I pull the plug and restart (so that the door will unlock), it gives F99, which goes away if I hit the power button, but F32 comes back in about 7 minutes of starting the wash.  I also checked the voltage on PS8 socket pin 1 and 2, and it shows 0.5V when the tub is empty, and when it starts filling, it slowly rises to 3.0V, and then I get F32 error.

The fill, spin, drain seem to work just fine.  I checked the pressure sensor tube at the top and it seems fine (although did not check the bottom, as it would require moving the machine).  I cleaned the filter to the drain-pump, and checked the pump for any debris.

When I run the diagnosis, it immediately gives F99 error and stops. What do you think is the issue? Thanks for your help.

Gerät:

Kenmore Washer

Status:

open