Einführungsvideo

Einleitung

Here is a video teardown of the ThinkPad T410s.

Below is a step by step teardown

Dieser Teardown ist keine Reparaturanleitung. Um dein Lenovo ThinkPad 410s zu reparieren, verwende unsere Fehlerbehebungsseite.

    • Unlatch and remove battery

    Kommentar hinzufügen

    • Open Acess panel

    Kommentar hinzufügen

    • Remove Hard drive

    Kommentar hinzufügen

    • Remove wirless WAN

    Kommentar hinzufügen

  1. Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    • Remove DIMM from back

    Kommentar hinzufügen

    • Remove Keyboard retaing Screw from bottom of system

    • Turn the system over and open the cover. Push the keyboard toward the back and lift it up. Slide it forward to rest it on the palm rest. Disconnect the ribbon cable.

    Kommentar hinzufügen

    • Remove BIOS battery

    Kommentar hinzufügen

    • Disconnect the two antenna leads from the Wireless WAN card. Remove the two retaining screws. Rotate the card up and pull it out of the slot.

    • Remeber which lead goes where Prior to removing it . Grey is usually MAIN , black AUX

    Kommentar hinzufügen

    • Remove 14 retaining screws from back

    • The first 9 are required for bezel and touchpad removal .

    • M2 × 14 mm, wafer-head, nylon-coated (6)

    • M2 × 3 mm, wafer-head, nylon-coated (3)

    • The remaining need to be removed for base cover removal

    • M2 × 5 mm, wafer-head, nylon-coated (4)

    • M2 × 10 mm, wafer-head, nylon-coated (1)

    • Note: The FPC cable is attached on the underside of the keyboard bezel assembly. In some models, the Bluetooth daughter card is also attached on the underside of the keyboard bezel assembly.

    Kommentar hinzufügen

    • Turn system over , open , remove 4 retaining screws and the work form one side , using spudger to remove chasis bezel

    • M2 × 3 mm, wafer-head, nylon-coated (4)

    Kommentar hinzufügen

    • Remove 4 retaining screws

    • M2 × 3 mm, wafer-head, nylon-coated (4)

    Kommentar hinzufügen

    • Remove the two retaining screws on the bottom of the system.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Turn the system over and open the cover.

    • Unroute all the wires.

    • Remove the retaining screws.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Carefully lift the LCD panel up and out of the chass

    Kommentar hinzufügen

kevinleroy

Mitglied seit 13.08.2012

326 Reputation

1 Anleitung geschrieben

Team

Master Techs Mitglied von Master Techs

Community

279 Mitglieder

758 Anleitungen geschrieben

Uhm, sorry, what about the photos? I don't see any...

JoeMuc2014 - Antwort

Still not seeing any photos accompanying the steps listed in the teardown.

Jason Landers - Antwort

well. if get short out inside of USB or network line>> that has been stopping the software lunched.

mohammed - Antwort

we need teardown of T410

mohammed - Antwort

The video shows a teardown of the T410s. It is a lot different from the T410.

Robert Oschmann - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 2

Letzte 7 Tage: 5

Letzte 30 Tage: 50

Insgesamt: 6,646