Speziell für diesen Teardown benötigte Werkzeuge

Einleitung

This guide shows you how to completely disassemble your camera.

Diese Demontage ist keine Reparaturanleitung. Um dein Polaroid One-Step 600 zu reparieren, verwende unsere Fehlerbehebungsseite.

Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal. Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal. Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal.
  • Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal.

Kommentar hinzufügen

Separate the flash section of the camera from the main body by unhooking the sides. BE CAREFUL NOT TO YANK THE TWO SECTIONS APART BECAUSE THE BAND WIRE STILL ATTACHES THEM! BE CAREFUL NOT TO YANK THE TWO SECTIONS APART BECAUSE THE BAND WIRE STILL ATTACHES THEM!
  • Separate the flash section of the camera from the main body by unhooking the sides.

  • BE CAREFUL NOT TO YANK THE TWO SECTIONS APART BECAUSE THE BAND WIRE STILL ATTACHES THEM!

Kommentar hinzufügen

Open the battery/ cartridge compartment fully.
  • Open the battery/ cartridge compartment fully.

Kommentar hinzufügen

Insert spudger in between face of camera and sides where the four tabs are located. Insert spudger in between face of camera and sides where the four tabs are located. Insert spudger in between face of camera and sides where the four tabs are located.
  • Insert spudger in between face of camera and sides where the four tabs are located.

Kommentar hinzufügen

Once tabs are released, pull face of camera straight out. Once tabs are released, pull face of camera straight out.
  • Once tabs are released, pull face of camera straight out.

Kommentar hinzufügen

Remove the capture button if it did not pop out when you removed the face. There are two pieces to the capture button and both should be removed.
  • Remove the capture button if it did not pop out when you removed the face.

  • There are two pieces to the capture button and both should be removed.

Kommentar hinzufügen

To remove the back of the camera, you have to find the tabs located near the hinges of the battery and film compartment. Using a screw driver, pry the tabs of the outer case away from the metal frame. Once the tabs are removed slide the metal frame forward.
  • To remove the back of the camera, you have to find the tabs located near the hinges of the battery and film compartment.

  • Using a screw driver, pry the tabs of the outer case away from the metal frame.

  • Once the tabs are removed slide the metal frame forward.

Kommentar hinzufügen

Remove the battery and film compartment latch Pull the metal frame away from the case.
  • Remove the battery and film compartment latch

  • Pull the metal frame away from the case.

  • The entire case will come off but the flash compartment will come with the insides of the camera.

Kommentar hinzufügen

Using a spudger, pop the battery and film cartridge hatch from its hinges.
  • Using a spudger, pop the battery and film cartridge hatch from its hinges.

  • The tabs are located at the bottom of the metal frame.

Kommentar hinzufügen

Remove the sight by lifting it straight up. Follow the red wire from the flash compartment Take the red wire off of the 2 hooks
  • Remove the sight by lifting it straight up.

  • Follow the red wire from the flash compartment

  • Take the red wire off of the 2 hooks

  • Slide the uncovered wire end out of the small brass clip. Move wire away from camera.

Kommentar hinzufügen

Follow the black wire from flash bulb to the back of the case. When you find the brass tab, pull it up. When the tab is free, remove the tab from the black wire. When you find the brass tab, pull it up. When the tab is free, remove the tab from the black wire.
  • Follow the black wire from flash bulb to the back of the case.

  • When you find the brass tab, pull it up. When the tab is free, remove the tab from the black wire.

Kommentar hinzufügen

Follow the metal band from the flash compartment to the brass tab. Unhook the wire on the left of the brass tab. Remove the metal band from behind the brass clip.
  • Follow the metal band from the flash compartment to the brass tab.

  • Unhook the wire on the left of the brass tab.

  • Remove the metal band from behind the brass clip.

  • Set the now detached flash compartment to the side.

  • Pull the brass tab up and out like the first one and remove the uncovered wire.

Kommentar hinzufügen

Slide the brightness adjuster to right and off the camera. Use the pointed end of the spudger to lift a small latch located next to the bottom of lenz plate Then find the small latch located below the plastic bridge that is over the shutter mechanism
  • Slide the brightness adjuster to right and off the camera.

  • Use the pointed end of the spudger to lift a small latch located next to the bottom of lenz plate

  • Then find the small latch located below the plastic bridge that is over the shutter mechanism

  • This latch is small and is hard to see but you just have to push it with the pointed end of the spudger to unlatch it.

Kommentar hinzufügen

Using the pointed end of the spudger, pull the band wire out of the electric motor. In the same manner as above, remove the band wire from the plastic extension.
  • Using the pointed end of the spudger, pull the band wire out of the electric motor.

  • In the same manner as above, remove the band wire from the plastic extension.

Kommentar hinzufügen

Rotate the lens plate up to unhook the plat from two tabs located at the top of the plate. Remove the lens plate, flash compartment and wires from the camera.
  • Rotate the lens plate up to unhook the plat from two tabs located at the top of the plate.

  • Remove the lens plate, flash compartment and wires from the camera.

Kommentar hinzufügen

Follow the uncovered wire around the side of the camera Remove the metal spring tab next to the counter Remove the brass tab by lifting the top piece over the notch and sliding back.
  • Follow the uncovered wire around the side of the camera

  • Remove the metal spring tab next to the counter

  • Remove the brass tab by lifting the top piece over the notch and sliding back.

Kommentar hinzufügen

Locate the small brass tab with the uncovered wire running through it. Remove the wire by sliding under the hooks. then unhook the uncovered wire from the the final latch located on the top of the plastic extension.
  • Locate the small brass tab with the uncovered wire running through it.

  • Remove the wire by sliding under the hooks.

  • then unhook the uncovered wire from the the final latch located on the top of the plastic extension.

Kommentar hinzufügen

The cameras insides could now be in two major pieces. The Pyramid and the lens plate
  • The cameras insides could now be in two major pieces.

  • The Pyramid and the lens plate

Kommentar hinzufügen

The top of the pyramid has cover that can be lifted off Below is the mirror which is held in by a tab. Lift the tab with the spudger and pop out the mirror.
  • The top of the pyramid has cover that can be lifted off

  • Below is the mirror which is held in by a tab.

  • Lift the tab with the spudger and pop out the mirror.

  • If you intend to reassemble the camera make sure the mirror is completely clean without any spots or fingerprints because they will affect the quality of your pictures.

Kommentar hinzufügen

There are 4 tabs total that must be removed for the next step The first is directly under the spring mounted at the back left of the camera The next is located on the front of the plastic extension
  • There are 4 tabs total that must be removed for the next step

  • The first is directly under the spring mounted at the back left of the camera

  • The next is located on the front of the plastic extension

  • The third tab is used to connect the metal frame to the outer plastic

Kommentar hinzufügen

The final tab holds several spring loaded pieces together, these may pop out the moment the tab is released. The final tab is located below the backside of the photo-counter dial.
  • The final tab holds several spring loaded pieces together, these may pop out the moment the tab is released.

  • The final tab is located below the backside of the photo-counter dial.

  • The numbers will be right side up if you are looking in the right direction.

  • Once all four tabs are removed the plate pulls out from the slot in the rear.

Kommentar hinzufügen

Lift the large gear away from its pin The next piece is loaded with a small spring. Carefully lift the "Y" shaped plastic piece from its pin and pull the spring from the pin as it is removed.
  • Lift the large gear away from its pin

  • The next piece is loaded with a small spring.

  • Carefully lift the "Y" shaped plastic piece from its pin and pull the spring from the pin as it is removed.

Kommentar hinzufügen

Remove the Spring attached to the photo-counter dial. Lift the photo-counter Dial off of its pin.
  • Remove the Spring attached to the photo-counter dial.

  • Lift the photo-counter Dial off of its pin.

Kommentar hinzufügen

Remove the spring attached to the film eject metal slide. Remove the film eject metal slide
  • Remove the spring attached to the film eject metal slide.

  • Remove the film eject metal slide

Kommentar hinzufügen

Remove the plastic extension by pulling it from the slot in the rear of the camera.
  • Remove the plastic extension by pulling it from the slot in the rear of the camera.

Kommentar hinzufügen

Remove the metal gear from the gear set. Pull the "L" shaped black plastic piece off of its pin.
  • Remove the metal gear from the gear set.

  • Pull the "L" shaped black plastic piece off of its pin.

Kommentar hinzufügen

There are four gears to remove. The gear on the left goes first, followed by the the right.
  • There are four gears to remove.

  • The gear on the left goes first, followed by the the right.

  • The right gear has a small leaf spring between it and the gear below it.

  • Then remove the black gear and then the last white gear.

Kommentar hinzufügen

Using the pointed end of the spudger, press the clip that is beneath all the gears next to the electric motor gear. Lift the plastic box containing several long metal tabs Then slide the box out.
  • Using the pointed end of the spudger, press the clip that is beneath all the gears next to the electric motor gear.

  • Lift the plastic box containing several long metal tabs

  • Then slide the box out.

Kommentar hinzufügen

Pull the electric motor straight out of the plastic piece.
  • Pull the electric motor straight out of the plastic piece.

Kommentar hinzufügen

Remove the spring located in the middle of the plastic mechanism. Remove the two loose plastic pieces. Remove the two loose plastic pieces.
  • Remove the spring located in the middle of the plastic mechanism.

  • Remove the two loose plastic pieces.

Kommentar hinzufügen

To remove the metal frame, press the two tabs with the spudger and slide it forward.
  • To remove the metal frame, press the two tabs with the spudger and slide it forward.

Kommentar hinzufügen

With the point of the spudger, remove the band wire from the solenoid. Remove the small LED from its clip, and then lift the flat wire array and the flash compartment away from the back of the lens plate.
  • With the point of the spudger, remove the band wire from the solenoid.

  • Remove the small LED from its clip, and then lift the flat wire array and the flash compartment away from the back of the lens plate.

Kommentar hinzufügen

Remove the solenoid from the back of the lens plate by removing the two tabs.
  • Remove the solenoid from the back of the lens plate by removing the two tabs.

Kommentar hinzufügen

Remove the lens by pressing the tab. CAUTION: The lens may pop out when the tab is released.
  • Remove the lens by pressing the tab.

  • CAUTION: The lens may pop out when the tab is released.

  • Remove the back of the lens plate by unhooking the three clips that hold it together.

  • CAUTION: The Shutter leaves may fall out during this step.

Kommentar hinzufügen

Remove the spring on the plastic bridge that attaches to the shutter mechanism Remove the Shutter mechanism from the back of the lens plate.
  • Remove the spring on the plastic bridge that attaches to the shutter mechanism

  • Remove the Shutter mechanism from the back of the lens plate.

Kommentar hinzufügen

Remove the Clear dial by unhooking the tab at the bottom of the dial Lift the light blue piece out of the mechanism. Lift the black piece out of the plastic plate.
  • Remove the Clear dial by unhooking the tab at the bottom of the dial

  • Lift the light blue piece out of the mechanism.

  • Lift the black piece out of the plastic plate.

Kommentar hinzufügen

Remove the clear green prism from the plastic plate.
  • Remove the clear green prism from the plastic plate.

Kommentar hinzufügen

The disassembled camera.
  • The disassembled camera.

how do you remove the neck strap and replace it with a strap that is 3/8" wide web? And if you could, please include photographs.

Thank you!

Kourtney - Antwort

Adriano Agostino

Mitglied seit 22.01.2010

27 Reputation

1 Anleitung geschrieben

Team

Cal Poly, Team 16-31, Maness Winter 2010 Mitglied von Cal Poly, Team 16-31, Maness Winter 2010

CPSU-MANESS-W10S16G31

4 Mitglieder

4 Anleitungen geschrieben

Is it possible to remove and change the camera straps for this camera?

stylencreate - Antwort

Yes, after step 8 you will have the back case free then in the inside you will see the latches of the plastic plate that holds the strap, pry them carefully are 6, 2 on each side and 2 in the middle, in the middle of doing it myself have stopped since was no need for that so cannot tell you more.

eportillo5000 - Antwort

Show me how to teardown the flash plz

RAW Fish - Antwort

RAW Fish: Get a terminal driver or other thin device, and wedge it where you can see a line between the outer casing and front panel (where it says “Polaroid” with the rainbow logo). This will need a bit of brute force, but you will be able to seperate a right-angle of outer casing, from the back of the flash, and another right angled bit full of electrics and the front panel. DO NOT touch any of this electrical gubbins - discharging the capacitor through your fingers will HURT. From here you can take out the circuit board and do with it what you wish.

Ariane N -

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 13

Letzte 7 Tage: 92

Letzte 30 Tage: 427

Insgesamt: 32,264