Zum Hauptinhalt wechseln

Was du brauchst

Dieser Teardown ist keine Reparaturanleitung. Um dein Toaster zu reparieren, verwende unsere Fehlerbehebungsseite.

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Breville Toaster.

    • The toaster before the teardown process.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • Turn the toaster upside-down.

    • Use the drill to unscrew the six slotted Spanner head screws

    • Use the drill with corresponding screwdriver bit to remove the Truss Phillip screws

    • The Slotted Spanner head screws hold the four rubber feet at the bottom of the casing.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Unattach the four rubber feet.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Detach the timer knob using a flat head screw driver

    • Remove the internal components from the red casing

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Note: Red casing is still attached to the interior body of the toaster.

    • Detach electric circuit housing from red casing

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 2 : Schritt 6, Bild 2 von 2
    • Firstly, unscrew the four Pan Phillip head screws

    • Then snap off the three welded plastic studs to detach the timer knob housing from the red casing

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Unfasten the two Pan Phillip head screws to detach the buttons' housing

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 3 : Schritt 8, Bild 2 von 3 : Schritt 8, Bild 3 von 3
    • Note: There are two housings attach to both side of the interior body of the toaster.

    • Remove the two Pan Phillip head screws to detach the circuit board from the heat controller housing.

    • Then, remove the slider as well.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 3 : Schritt 9, Bild 2 von 3 : Schritt 9, Bild 3 von 3
    • Remove the circuit board housing for the heat controller from the interior body of the toaster by unscrewing two Pan Phillip head screws

    • Remove the cable fasteners using a flat head screw driver

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 3 : Schritt 10, Bild 2 von 3 : Schritt 10, Bild 3 von 3
    • Separate the interior body of the toaster from the bottom cover.

    • Remove the screw caps

    • Unscrew the two Pan Phillip head screws to detach the aluminium vent

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 3 : Schritt 11, Bild 2 von 3 : Schritt 11, Bild 3 von 3
    • Use pliers to break apart the welded wires from the interior body.

    • Snip off the rest of the wires still attached to the interior body using a wire cutter

    • Remove the circuit board from its housing

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 2 : Schritt 12, Bild 2 von 2
    • Separate the electric components from the interior body

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 1
    • Insert wisdom here.

Aisyah Azmi

Mitglied seit: 09/30/18

217 Reputation

1 Anleitung geschrieben

11 Kommentare

Don’t buy this toaster…They fail and Breville won’t warranty it after 1 year….

Never again Breville..

James Payne - Antwort

Thank you for this tear down guide. Though it’s built pretty well and feels like a tank, It doesn’t seem very repairable. Mine stopped working a couple months ago and I’m contemplating throwing it out. Comments?

David Vileta - Antwort

any chance you still have the electronics for the toaster. Mine stopped working. It’s not the heating element. I THINK the issue is one of the components on the circuit board failed. I’ll buy the harness with the PCB from you, if it’s still around. Thanks.

Riccardo - Antwort

Thanks very much for posting all of this, gave me the confidence to 'go in'.

Foe anyone thinking of doing what I just did; the guts of a plastic cased model can be put into a metal cased model but there are a few differences but everything you need is there.

Sean Johnson - Antwort

Purchased a Breville die cast 2 slice toaster ($160). After one year it stopped toasting evenly and then on the out side of one slice. I am capable of fixing this but Breville will not sell parts, they want you to buy a new one. My first and last Breville product.

Lou Viscomi - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 13

Letzte 7 Tage: 55

Letzte 30 Tage: 231

Insgesamt: 19,259