dr ing ernesto cuadra

please go to the next link: [[URL|iPhone 4S Repair|Link] and repase the instruction God bless you

go to control panel and use the utility system, and "restore system" and put the last days that you know was worling good. However if the problem persist, you must update your driver can be corrupted. downlod from your supplier computer website and donwload for free. God bless you

please follow this steps and fix it. God bless you traighten a paper clip and push one end into the small hole at the top of the iPhone. This pops out the SIM card holder. Remove the SIM card. Push the SIM card holder closed. 2 Remove the two screws on the bottom of the iPhone with a small Phillips screwdriver. 3 Look for the seam between the body of the iPhone and the screen. This is found just above the "Home" button. Insert the pry tool in the seam and pry the screen up from the body to expose the connectors. Do not remove it all the way. 4 Remove the two connector wires with the pry tool. Flip the white latch up with the pry tool and remove the ribbon attached to the base. 5 Pull the two black strips of tape off the left and right sides of the screen with tweezers. 6 Remove the five screws holding the LCD assembly to the screen frame of the iPhone. Use the small Phillips screwdriver. 7 Insert the pry tool between the screen frame and the LCD assembly. Pop the screen frame up and pull it away from the...

please use small plastic with RICE and put the phone by 24 hours. The rice will be absorb the humidity. However this is a 98% from can be work. If after you did the problem remain , the backlight is faulty. God bless you

please follow this test and fix it. God bless you Bad cable connection Check the USB cable for damage and dirt, especially at the ends. Then try using the wall charger, as this will provide greater power input than the computer/USB. Broken charger or USB cord Try using different chargers to see if you may have a problem with your charger or cord. Obstructed/bad dock connector Inspect the 30-pin dock connector at the bottom of the iPhone for dirt, lint, and damaged pins. Clean out the dock connector very carefully with a tooth pick or soft toothbrush. If the dock connector is broken, you will have to replace it.

go please to http://www.ebay.com/sch/i.html?_nkw=ipho... and get it. God bless you dr ing ernesto a cuadra

follow this steps and fix it. God bless you Lid Switch Assembly If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design. Door Lock Motor and Switch Assembly If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design. Water Inlet Valve If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water...

please go to the website and translate with the web browser and fix it. http://www.automecanico.com] God bless you

Please download the BIOS update from the manufacturer supplier computer very importan.When you have the BIOS update so do the follow: a) open the computer and disconnect the small battery for 3V, by 1 minute. b) then connect again. c) and discharge the BIOS update and follow the step, and try it, must fix it. God bless you

run the sotware coming the computer . restar the computer and hold the key f2 before to to the operative system and follow the step for test the battery. However you can test the adapter battery and contacts for adapter, they can by damaged measure the output read your tech speci from adpater and measue the same voltage otherwise the adapter is FAULTY. God bless you