Einleitung

Removing the keyboard plate cover will allow access to all internal components of the laptop.

Ersatzteile

Kein Ersatzteil erforderlich.

Power off and unplug your laptop before you begin.
  • Power off and unplug your laptop before you begin.

  • Turn the laptop upside-down and remove the following screws using a Phillips #0 driver:

    • Two 9.5 mm screws in the middle of the back edge, and one 9.5 mm screw in the right edge

    • Two 4.3 mm screws in the back corners

    • One 17.5 mm screw at the left edge near the optical drive

    • Three 4.3 mm screws in the front edge

screw assignments are definitely wrong. I swapped the red and the green, as per comment above, and kept the blue as-is.

jasonbuechler - Antwort

jason is right

starwilson - Antwort

correct, swap the green and red

Josh - Antwort

Jason is correct

Clem Lanoe - Antwort

Thanks everyone. It does seem like someone got their screws mixed up when they wrote this guide. I’ve made some changes as you all suggested, so the screw placements should be more accurate now. If anyone with this laptop could verify the screw measurements with a digital caliper, that’d also be very helpful.

Jeff Suovanen - Antwort

Use the plastic opening tool to separate the keyboard plate cover from the bottom cover. In order to do this, insert the plastic opening tool in between the keyboard plate cover and the bottom cover, then slide along edges to pry open.
  • Use the plastic opening tool to separate the keyboard plate cover from the bottom cover. In order to do this, insert the plastic opening tool in between the keyboard plate cover and the bottom cover, then slide along edges to pry open.

Kommentar hinzufügen

Locate the three ribbons connecting the keyboard plate cover to the bottom cover.
  • Locate the three ribbons connecting the keyboard plate cover to the bottom cover.

Kommentar hinzufügen

Invert the laptop in order to gain access to the ribbons. Remove each ribbon by flipping the small white plastic flap up and gently pulling on the ribbon. Remove each ribbon by flipping the small white plastic flap up and gently pulling on the ribbon.
  • Invert the laptop in order to gain access to the ribbons.

  • Remove each ribbon by flipping the small white plastic flap up and gently pulling on the ribbon.

Don't remove the ribbons, just move the keyboard slightly forward to remove the old battery and insert the new one (just make sure they are all connected when you put it back)

Flyer292 - Antwort

Now that the ribbons have been detached from the bottom cover, carefully remove the keyboard plate cover. Once it has been removed, place it in a safe and moisture free area so it does not get damaged.
  • Now that the ribbons have been detached from the bottom cover, carefully remove the keyboard plate cover. Once it has been removed, place it in a safe and moisture free area so it does not get damaged.

Is painting your nails crucial for step 5?

wiedzmin - Antwort

Yes and you have to put lotion on

joemidjette - Antwort

Now, that is a stupid question! Of course! As I am working on 551M, I naturally have to have nails painted orange, with blue accents!

gregtokarski -

that boy ain't right

Rich Spillman - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

9 weitere Nutzer haben diese Anleitung absolviert.

Josh

Mitglied seit 10.04.2014

2.500 Reputation

12 Anleitungen geschrieben

Team

Cal Poly, Team 7-22, Regan Spring 2014 Mitglied von Cal Poly, Team 7-22, Regan Spring 2014

CPSU-REGAN-S14S7G22

5 Mitglieder

15 Anleitungen geschrieben

WARNING the screw lengths in step 1 are wrong. I tried installing the wrong screws and now my touch pad us ruine

Joe Allen - Antwort

The screw info has been updated. I’m still not sure if it’s 100% correct, so be sure to keep your screws organized and put each one back where it came from to avoid damage.

Jeff Suovanen -

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 2

Letzte 7 Tage: 13

Letzte 30 Tage: 53

Insgesamt: 3,391