Einleitung
Amazons Kindle Paperwhite 3 ist mit einer GS957661, 3G Hauptplatine ausgestattet. Für die Reparatur muss das Gerät ausgeschaltet sein. Als Werkzeug benötigst du ein Plastiköffnungswerkzeug, eine gewinkelte Pinzette und einen Kreuzschlitzschrauber PH000
Was du brauchst
-
-
Heble die Blende mit einem Plastiköffnungswerkzeug vorsichtig ab. Beginne an den Ecken und schiebe das Werkzeug um die Kanten herum, bis du wieder am Ausgangspunkt angelangt bist.
-
-
-
Sei besonders vorsichtig, wenn du die Blende abhebelst. Das Werkzeug darf nicht unter das Display gelangen. Schaue unter die Abdeckung, du musst den Kleber an der Blende auftrennen.
-
Achte darauf, dass du auf beiden Seiten der Blende mit dem Werkzeug über dem Display bleibst.
-
Beim zweiten Foto siehst du, auf welche Weise das Trennwerkzeug zwischen Blende und Display liegen muss.
-
Beim dritten Foto siehst du, was falsch gehen kann. Falls das wirklich passiert, arbeitet dein Touchscreen nicht mehr richtig und das Display ist dauerhaft beschädigt.
-
-
-
Drehe elf 3,2 mm Kreuzschlitzschrauben #000 am Rand des Rahmens heraus.
Mine had 11, as per the instructions, one of which was hidden under tape. I cut an opening in it.
Should have read Glover's comment.
Looked for the middle screw but the black tape covered all appearances of it. Lifting the mid-frame out of the case snapped the mount. However, there was plenty of support with the ten screws and no lasting damage to the reader.
-
-
-
Hebe den Mittelrahmen vorsichtig mit der Hand aus dem Gehäuse heraus.
-
-
-
-
Der Akku ist mit drei 3,0 mm Kreuzschlitzschrauben #000 befestigt. Drehe sie heraus.
-
-
-
Hebe den Akku vorsichtig aus dem Rahmen heraus.
We had a Kindle that unfortunately took a dunk in (clean) water. It was then inoperative. I followed this guide, and took the battery out, let everything dry for a few days, then replaced the battery. Now it works fine! Thanks!
-
-
-
Klappe den Sicherungsbügel mit einem Plastiköffnungswerkzeug hoch. Ziehe dann vorsichtig das orangene Flachbandkabel heraus.
-
-
-
Klappe die kleine schmutzigweiße Lasche mit einer gewinkelten Pinzette in Richtung des Akkus.
-
Ziehe das orangene Flachbandkabel vorsichtig heraus.
-
-
-
Löse das orangene Flachbandkabel nahe am Akku ab.
-
Klappe die kleine schwarze Lasche mit der gewinkelten Pinzette zur nahen Gehäusekante hin.
-
-
-
Entferne sechs 3,0 mm Kreuzschlitzschrauben #000, welche die Hauptplatine befestigen
-
Entferne die einzelne 2,5 mm Kreuzschlitzschraube #000
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
10 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
5 Kommentare
Tip, heat the front bezel to soften the glue.
I totally know how to fix my kindle but I don’t know where to get the part. I broke the tip to the ribbon cable for the only %#*@ button on the device. do they sell those here?
Be very careful along the lower left side, where the cable to the touchscreen can be easily cut with a plastic spudger.
John Kenny - Antwort
Be careful at the top of the 3G version. The wifi and cell antennas are located along here.
James Sullivan - Antwort
I can’t get my spudger in to start lifting. Any advice?
Davey - Antwort
it takes a bit of force to first insert the spudger into the crack
jookieapc -
Be careful inserting the spudger too quickly. The glue holding the screen pulled loose in two spots along the side before the bezel did and there are lines along the border of my screen now.
Nick - Antwort
I made my own version of Nick’s error: I inserted a pick too far under the bezel, and very slightly separated the screen, leaving a small shadow in a corner. Easy does it!
Other than that, battery replacement was super-easy and successful.
Brad Compton - Antwort
I couldn't get a purchase from the outside, so started from the inside of the bezel. It was secured with double sided tape. Might have been better to apply some heat before prying.
David Glover - Antwort
Used the guide to replace the battery. Could not get enough separation using the blue spudger. Used the metal spidger to get things started then switched to the blue picks. Afterthought, Warming the bezel would have helped.
Jeffry Long - Antwort