Einleitung

This guide demonstrates how to install a LCD.

Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.
  • Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.

Kommentar hinzufügen

Press thumb firmly on battery door and slide it in the direction of the arrow.
  • Press thumb firmly on battery door and slide it in the direction of the arrow.

  • Lift thumb allowing the door to swing open.

Kommentar hinzufügen

Kommentar hinzufügen

  • Turn the camera off by firmly pressing the power button located on top of the camera.

Kommentar hinzufügen

  • Locate the 7 screws holding the back cover on.

    • Three screws are located on the bottom of the camera.

    • Two screws are located on the side shown in the photograph.

    • Two final screws are located on the opposite side shown in the photograph.

Kommentar hinzufügen

  • Remove all 7 screws:

    • Hold the camera firmly with one hand so that you can still see a screw.

    • Place the Philips 00(Found here)screwdriver into the screw.

    • Turn the screwdriver to the left until it is free.

    • Repeat for the remaining screws.

Kommentar hinzufügen

  • Use plastic opening tools to slightly open the side of the case.

  • Insert a plastic opening tool and apply pressure to the internal three tabs at the top.

    • The first two are near the words "3X Optical Zoom".

    • The third is near the shutter button.

Kommentar hinzufügen

  • Gently pull apart the back cover from the rest of the camera.

    • Make sure there are no more screws or tabs keeping the cover on.

    • Use the plastic opening tool to separate any sides still closely connected.

Kommentar hinzufügen

  • Open the battery door.

    • Press thumb firmly on battery door and slide it in the direction of the arrow.

    • Lift thumb allowing the door to swing open.

The battery door on my easyshare c813 is broken. How can i get a replacement door?

paul chadwell - Antwort

  • Use the plastic opening tool to lift the casing around the shutter button.

  • Gently remove the front cover from the device.

Kommentar hinzufügen

  • Do not touch the terminals shown in the photo. These link to the capacitor which could shock you if not discharged.

  • To discharge the capacitor follow this guide.

Kommentar hinzufügen

  • Once the front cover is removed, the battery door maybe closed for convenience.

  • Locate the exposed portion of the LCD screen.

  • Use a wedge to free the LCD screen from the medal housing.

  • Do not pull the screen away completely, it is still attached to the logic board via the yellow cable.

Kommentar hinzufügen

  • Remove the screw at the upper right corner of the metal housing.

Kommentar hinzufügen

  • Locate the 2 solder joints holding down the medal housing.

  • Remove the solder.

    • Place wick on solder.

    • Place solder iron on wick

    • The wick should be sandwiched between the iron and the solder.

Kommentar hinzufügen

  • Peel back the black tape from the metal housing.

  • Lift the metal housing from the left so that it hinges on its right side.

    • The metal housing is still loosely attached on its right side.

Kommentar hinzufügen

  • Locate black tab holding the LCD screen connector in the port.

  • Use wedge or fingernail to lift the black tab.

  • Pull the the LCD screen connector out of the port.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Samantha Murray

Mitglied seit 15.04.2010

218 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 24-22, Regan Spring 2010 Mitglied von Cal Poly, Team 24-22, Regan Spring 2010

CPSU-REGAN-S10S24G22

4 Mitglieder

10 Anleitungen geschrieben

De sluiterknop werkt niet altijd, hoe is dit op te lossen?

Jacobus Rijken - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 7

Insgesamt: 12,550