Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

Follow this guide to replace the fingerprint reader in your Lenovo YOGA 730-15IKB. The fingerprint reader recognizes your unique fingerprint and allows you to easily unlock the laptop.

See the troubleshooting page first to diagnose any software issues related to the fingerprint reader. If your fingerprint reader is scratched or does not recognize your fingers, you might need to replace it with a new, functional model.

  1. Turn off the computer and unplug the charger before going any further. Flip the laptop over so you can see the underside.
    • Turn off the computer and unplug the charger before going any further.

    • Flip the laptop over so you can see the underside.

    • Remove ten 7mm T5 Torx screws.

  2. Pry up the bottom cover with an opening tool. Start at the front edge of the cover and make your way along the sides.
    • Pry up the bottom cover with an opening tool.

    • Start at the front edge of the cover and make your way along the sides.

  3. Pull the bottom cover up and away from the back hinges.
    • Pull the bottom cover up and away from the back hinges.

  4. Remove the battery connector by tugging and wiggling the battery wire using your fingers or a pair of tweezers. Unplug the cable gently as the eight wires on the connector are very small and delicate. Unplug the cable gently as the eight wires on the connector are very small and delicate.
    • Remove the battery connector by tugging and wiggling the battery wire using your fingers or a pair of tweezers.

    • Unplug the cable gently as the eight wires on the connector are very small and delicate.

  5. Remove four 4mm Phillips #1 screws. Remove four 4mm Phillips #1 screws.
    • Remove four 4mm Phillips #1 screws.

  6. Pull the battery up and out of the chassis.
    • Pull the battery up and out of the chassis.

    • Handle the battery carefully. Touching the terminal may cause electric shock. Puncturing the battery may cause it to catch fire.

  7. When the laptop is upside down, the left fan is on the right side of the laptop near the wireless card and the SSD.
    • When the laptop is upside down, the left fan is on the right side of the laptop near the wireless card and the SSD.

    • Remove the black and white antenna wires from the groove on the right side of the fan.

  8. Disconnect the fan cable. Pull the wire toward the right side of the laptop while wiggling to loosen the connection. You can also use the white tabs on the connector to push the cable free.
    • Disconnect the fan cable. Pull the wire toward the right side of the laptop while wiggling to loosen the connection.

    • You can also use the white tabs on the connector to push the cable free.

  9. Remove two 4mm Phillips #1 screws. Remove two 4mm Phillips #1 screws.
    • Remove two 4mm Phillips #1 screws.

  10. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  11. Pull the fan up and towards the front of the laptop.
    • Pull the fan up and towards the front of the laptop.

  12. When the laptop is upside down, the right fan is on the left side of the laptop near the large metal RAM cover.
    • When the laptop is upside down, the right fan is on the left side of the laptop near the large metal RAM cover.

    • Disconnect the fan cable. Pull the wire toward the back of the laptop while wiggling to loosen the connection.

    • You can also use the white tabs on the connector to push the cable free.

  13. Remove two 4mm Phillips #1 screws. Remove two 4mm Phillips #1 screws.
    • Remove two 4mm Phillips #1 screws.

  14. Pull the fan up and towards the front of the laptop.
    • Pull the fan up and towards the front of the laptop.

  15. Remove the fingerprint reader ribbon cable located at the bottom left of the motherboard. Pull up on the black tab on the connector. The ribbon cable should easily pull out of the connector.
    • Remove the fingerprint reader ribbon cable located at the bottom left of the motherboard.

    • Pull up on the black tab on the connector.

    • The ribbon cable should easily pull out of the connector.

  16. Remove the three other ribbon cables at the lower edge of the motherboard. For each, lift up the black tab on the connector.
    • Remove the three other ribbon cables at the lower edge of the motherboard.

    • For each, lift up the black tab on the connector.

    • The ribbon cables should easily pull out of the connectors.

  17. Disconnect the speaker cable by pulling the wire towards the front of the laptop. You can also use the white tabs on the connector to push the cable free. You can also use the white tabs on the connector to push the cable free.
    • Disconnect the speaker cable by pulling the wire towards the front of the laptop.

    • You can also use the white tabs on the connector to push the cable free.

  18. Remove the sticky tape from the top of the wireless card.
    • Remove the sticky tape from the top of the wireless card.

  19. Pull the black and white antenna wires off of the wireless card. For reassembly, the white wire connects to the right terminal marked "1." The black wire connects to the left terminal marked "2." For reassembly, the white wire connects to the right terminal marked "1." The black wire connects to the left terminal marked "2."
    • Pull the black and white antenna wires off of the wireless card.

    • For reassembly, the white wire connects to the right terminal marked "1." The black wire connects to the left terminal marked "2."

  20. Pull up on the thick gray display cable near the back of the laptop to disconnect the display. Pull up on the thick gray display cable near the back of the laptop to disconnect the display.
    • Pull up on the thick gray display cable near the back of the laptop to disconnect the display.

  21. The charger port is connected to the computer by a cable at the top left of the motherboard. Disconnect the cable by pulling the bundle of wires firmly toward the back of the laptop. The cable requires some force to remove. Make sure you do not damage the connector or cable.
    • The charger port is connected to the computer by a cable at the top left of the motherboard.

    • Disconnect the cable by pulling the bundle of wires firmly toward the back of the laptop.

    • The cable requires some force to remove. Make sure you do not damage the connector or cable.

  22. Remove four 4mm Phillips #1 screws. Remove four 4mm Phillips #1 screws.
    • Remove four 4mm Phillips #1 screws.

  23. Pull the motherboard up out of the laptop chassis.
    • Pull the motherboard up out of the laptop chassis.

    • If you are replacing the motherboard, make sure to remove the SSD, wireless card, heat sink, and extra RAM. Transfer these components to the new motherboard.

  24. Remove one 2mm Phillips #1 screw. Remove one 2mm Phillips #1 screw.
    • Remove one 2mm Phillips #1 screw.

  25. Remove the small metal plate from above the reader.
    • Remove the small metal plate from above the reader.

    • The ribbon should be kept in case the new fingerprint reader doesn't come with a new ribbon to connect it to the motherboard.

  26. Pull the fingerprint reader up out of the chassis.
    • Pull the fingerprint reader up out of the chassis.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Team

Cal Poly, Team S1-G6, White Winter 2020 Mitglied von Cal Poly, Team S1-G6, White Winter 2020

CPSU-WHITE-W20S1G6

3 Mitglieder

13 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 0

Letzten 30 Tage: 7

Insgesamt: 34