Einleitung

This will guide you through the process of replacing your logic board.

Ersatzteile

Kein Ersatzteil erforderlich.

Remove the parallel port cover on the back of the PlayStation.
  • Remove the parallel port cover on the back of the PlayStation.

The SCPH-9001 model does not have the Parallel Port panel to remove.

Aislinn - Antwort

Flip over the PlayStation and remove the six screws from the bottom.
  • Flip over the PlayStation and remove the six screws from the bottom.

Kommentar hinzufügen

Turn the PlayStation upright. Remove the cover by lifting it up.
  • Turn the PlayStation upright. Remove the cover by lifting it up.

Kommentar hinzufügen

Carefully disconnect the gold-colored ribbon cable from it's connector.
  • Carefully disconnect the gold-colored ribbon cable from it's connector.

  • To avoid damaging the cable, pull it by the white, reinforced tab.

Kommentar hinzufügen

Disconnect the second cable by pulling up on the plastic connector at the end.
  • Disconnect the second cable by pulling up on the plastic connector at the end.

While I was pulling this cable, the whole connector came off the motherboard (the white part that's supposed do stay on the motherboard)... How can I fix it?

Zvezdan Disic - Antwort

Do I solder it or what?

Zvezdan Disic - Antwort

Kostenloser Versand bei allen Bestellungen ab 79,00 $.

Schau dich im Store um
MANTA DRIVER KIT
112 bit driver kit $59.99
MANTA DRIVER KIT
112 bit driver kit $59.99
Lift the optical drive off of the PlayStation.
  • Lift the optical drive off of the PlayStation.

Kommentar hinzufügen

Remove the four screws from the logic board's metal cover.
  • Remove the four screws from the logic board's metal cover.

Kommentar hinzufügen

Detach power supply connector from logic board by pulling on the plastic tab.
  • Detach power supply connector from logic board by pulling on the plastic tab.

Kommentar hinzufügen

Detach white ribbon cable from logic board by gently lifting on it.
  • Detach white ribbon cable from logic board by gently lifting on it.

Kommentar hinzufügen

With one hand, hold the main board’s protective metal cover. With your other hand, wedge the spudger in between the right side of the protective cover and the thin metal clamps that surround it.
  • With one hand, hold the main board’s protective metal cover. With your other hand, wedge the spudger in between the right side of the protective cover and the thin metal clamps that surround it.

  • With the spudger in place, gently lift the upper portion of the metal cover. The cover should detach from the right side.

Kommentar hinzufügen

Using the same process from the previous step, wedge the spudger between the clamps and metal cover on the bottom side (as shown in the picture).
  • Using the same process from the previous step, wedge the spudger between the clamps and metal cover on the bottom side (as shown in the picture).

  • With your other hand, pull up on the top right corner of the metal cover to lift it off.

Kommentar hinzufügen

Remove the last four screws from the logic board.
  • Remove the last four screws from the logic board.

Kommentar hinzufügen

Lift the logic board out of the PlayStation and replace with a new logic board.
  • Lift the logic board out of the PlayStation and replace with a new logic board.

Kommentar hinzufügen

Schluss

To reassemble your device, follow these instructions in reverse order.

11 weitere Nutzer haben diese Anleitung absolviert.

JakeDeschamps

Mitglied seit 28.10.2009

945 Reputation

6 Anleitungen geschrieben

Team

Cal Poly, Team 5-2, Regan Fall 2009 Mitglied von Cal Poly, Team 5-2, Regan Fall 2009

CPSU-REGAN-F09S5G2

5 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 3

Letzte 7 Tage: 34

Letzte 30 Tage: 152

Insgesamt: 16,667