Place your Sony Ericsson W810I screen side down with the battery cover facing up as shown.
  • Place your Sony Ericsson W810I screen side down with the battery cover facing up as shown.

Kommentar hinzufügen

Remove the battery cover by applying downward pressure on the Singular Symbol and then shifting the pressure towards the bottom edge of the phone.
  • Remove the battery cover by applying downward pressure on the Singular Symbol and then shifting the pressure towards the bottom edge of the phone.

Kommentar hinzufügen

Lift the bottom of the battery away from the phone with your thumb and rotate until the opening in the bottom of the case is oriented downward.   The battery should slide out. Lift the bottom of the battery away from the phone with your thumb and rotate until the opening in the bottom of the case is oriented downward.   The battery should slide out.
  • Lift the bottom of the battery away from the phone with your thumb and rotate until the opening in the bottom of the case is oriented downward. The battery should slide out.

Kommentar hinzufügen

Remove the two 3.9mm screws with a Phillips size #00 screwdriver. Remove the two 6.35mm screws with a Torx T6 screwdriver. Remove the two 6.35mm screws with a Torx T6 screwdriver.
  • Remove the two 3.9mm screws with a Phillips size #00 screwdriver.

  • Remove the two 6.35mm screws with a Torx T6 screwdriver.

Kommentar hinzufügen

Run a plastic opening tool along the edge of the back casing while prying it apart to remove it. Run a plastic opening tool along the edge of the back casing while prying it apart to remove it. Run a plastic opening tool along the edge of the back casing while prying it apart to remove it.
  • Run a plastic opening tool along the edge of the back casing while prying it apart to remove it.

Kommentar hinzufügen

Turn the phone over and open the memory stick compartment. Stick a plastic opening tools into the opening and twist it to gain some leverage.  This should begin separating the front casing from the interior plastic support frame. Stick a plastic opening tools into the opening and twist it to gain some leverage.  This should begin separating the front casing from the interior plastic support frame.
  • Turn the phone over and open the memory stick compartment.

  • Stick a plastic opening tools into the opening and twist it to gain some leverage. This should begin separating the front casing from the interior plastic support frame.

Kommentar hinzufügen

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Run the plastic opening tool upwards along that side, removing the housing. Run the plastic opening tool upwards along that side, removing the housing. Run the plastic opening tool upwards along that side, removing the housing.
  • Run the plastic opening tool upwards along that side, removing the housing.

Kommentar hinzufügen

Peel the rubber keys away from their backing.  Do not slide them off. Set them aside. Set them aside.
  • Peel the rubber keys away from their backing. Do not slide them off.

  • Set them aside.

Kommentar hinzufügen

Insert a plastic opening tool under the left side of the keypad backing and start to lift. Lift slowly, as you can damage the ribbon cable underneath if you pull the keypad backing away too forcefully. Lift slowly, as you can damage the ribbon cable underneath if you pull the keypad backing away too forcefully.
  • Insert a plastic opening tool under the left side of the keypad backing and start to lift.

  • Lift slowly, as you can damage the ribbon cable underneath if you pull the keypad backing away too forcefully.

Kommentar hinzufügen

Insert the plastic opening tool under the ribbon cable attachment and give a small push upwards to dislodge it. Insert the plastic opening tool under the ribbon cable attachment and give a small push upwards to dislodge it. Insert the plastic opening tool under the ribbon cable attachment and give a small push upwards to dislodge it.
  • Insert the plastic opening tool under the ribbon cable attachment and give a small push upwards to dislodge it.

Kommentar hinzufügen

Remove the indicated 6.35mm screws with a Torx T6 screwdriver. Remove the indicated 6.35mm screws with a Torx T6 screwdriver. Remove the indicated 6.35mm screws with a Torx T6 screwdriver.
  • Remove the indicated 6.35mm screws with a Torx T6 screwdriver.

Kommentar hinzufügen

Pull LCD screen gently out and the to side.  Do not attempt to pull it completely away from the board below it. Push up on the underside of the cable at the point of attachment with a plastic opening tool to detach it.  The screen can now be separated. Push up on the underside of the cable at the point of attachment with a plastic opening tool to detach it.  The screen can now be separated.
  • Pull LCD screen gently out and the to side. Do not attempt to pull it completely away from the board below it.

  • Push up on the underside of the cable at the point of attachment with a plastic opening tool to detach it. The screen can now be separated.

Kommentar hinzufügen

Using a plastic opening device, push against the underside of the brown portion of the the ribbon cable to unplug it. Using a plastic opening device, push against the underside of the brown portion of the the ribbon cable to unplug it. Using a plastic opening device, push against the underside of the brown portion of the the ribbon cable to unplug it.
  • Using a plastic opening device, push against the underside of the brown portion of the the ribbon cable to unplug it.

Kommentar hinzufügen

Using a plastic opening device, separate the top of the motherboard from the rest of the plastic casing.
  • Using a plastic opening device, separate the top of the motherboard from the rest of the plastic casing.

Kommentar hinzufügen

Pull forwards slightly on the motherboard so that it starts to fall out of the casing. Thread the ribbon cable through the hole in the motherboard so that it does not become caught. Thread the ribbon cable through the hole in the motherboard so that it does not become caught.
  • Pull forwards slightly on the motherboard so that it starts to fall out of the casing.

  • Thread the ribbon cable through the hole in the motherboard so that it does not become caught.

Kommentar hinzufügen

This is the vibration cell.  It causes the phone to vibrate when the vibrate setting is active.
  • This is the vibration cell. It causes the phone to vibrate when the vibrate setting is active.

Kommentar hinzufügen

Insert the spudger into the crack between the green rubber container and the plastic case and pry it out.  When the cell it is about halfway out, remove the spudger. Reinsert the spudger into the crack between the metal top and the plastic case and pry it the rest of the way out. Reinsert the spudger into the crack between the metal top and the plastic case and pry it the rest of the way out.
  • Insert the spudger into the crack between the green rubber container and the plastic case and pry it out. When the cell it is about halfway out, remove the spudger.

  • Reinsert the spudger into the crack between the metal top and the plastic case and pry it the rest of the way out.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Lucy Bowen

Mitglied seit 01.09.2011

353 Reputation

14 Anleitungen geschrieben

Team

Cuesta, Team 1-7, Zipperian Fall 2011 Mitglied von Cuesta, Team 1-7, Zipperian Fall 2011

CUESTA-ZIPPERIAN-F11S1G7

1 Mitglied

14 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 6

Insgesamt: 1,426