Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Store

Einleitung

The Joysticks on your Xbox Controller could become unresponsive or sticky. If this happens it could be necessary to remove the Joysticks to either replace or clean them. This guide will teach you how to access and replace the Joysticks on your Xbox One Wireless Controller Model 1708.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Slide the battery cover toward the top of the controller to remove it. Lift up  the batteries or the battery pack from the battery compartment.
    • Slide the battery cover toward the top of the controller to remove it.

    • Lift up the batteries or the battery pack from the battery compartment.

  2. Insert a plastic opening tool into the top seam, and  gently work the opening tool to the bottom of the controller. Continue using the opening tool to gently pry the side plate off of the controller.
    • Insert a plastic opening tool into the top seam, and gently work the opening tool to the bottom of the controller.

    • Continue using the opening tool to gently pry the side plate off of the controller.

    • Repeat this process for the second side plate.

  3. Gently peel the battery label  or punch a hole in the center of the sticker in the battery compartment to reveal the hidden screw.
    • Gently peel the battery label or punch a hole in the center of the sticker in the battery compartment to reveal the hidden screw.

    • Remove the five 9mm torx-9 security screws from the back of the controller.

  4. Orient the controller so the front plate is facing up. Lift the front cover off of the controller.
    • Orient the controller so the front plate is facing up.

    • Lift the front cover off of the controller.

  5. Turn the controller face down and gently lift the rear plate.
    • Turn the controller face down and gently lift the rear plate.

  6. Pull the joysticks off of the controller.
    • Pull the joysticks off of the controller.

Abschluss

To reassemble your device, follow these instructions in reverse order.

90 weitere Nutzer haben diese Anleitung absolviert.

Dylan Gross

Mitglied seit: 25.09.2017

3.654 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team S18-G3, Forte Fall 2017 Mitglied von Cal Poly, Team S18-G3, Forte Fall 2017

CPSU-FORTE-F17S18G3

4 Mitglieder

14 Anleitungen geschrieben

How about the square thing with the stick and hinges that the joystick is attached to? I think it’s called the Module. I have a joystick drift / drifting problem and that may help me out. Thanks.

Cory C - Antwort

Agreed. That’s actually the part I need to replace too. The module.

Thomas Tomchak -

followed this guide to take the controller apart because I had a joystick that was sticking, my solution was to put some 3in1 oil on the module that was sticking and it seems to be working a lot better now.

John Jaggi - Antwort

@corytc and @tomchak I did replace the module, in general, you buy (Amazon or eBay) you will receive a module of 6 modules you need a multimeter and test each module interface, measure both resistances and subtract them, the one nearest zero is the module you will use since is the one with least drift from the factory.

Just disassemble it, turn upside down uses a solder remover and unsolder the old one, place the new one solder back, boom you are done.

Like you will need an iron solder with medium and thin tips, I used lead-free solder, so is a patience test, be careful with the wires from the rumbles, try not to unsolder them since is a thin wire and is difficult, like I have big hands so took me a while to solder back.

Luis Vitorio Cargnini - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 32

Letzten 7 Tage: 227

Letzten 30 Tage: 926

Insgesamt: 24,598