Zum Hauptinhalt wechseln

Einleitung

This guide covers how to remove the Blu Ray disk drive in the Xbox One X. This is a straightforward process once the outer shell of the Xbox has been removed.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input. Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.
    • Use a T9 Torx screwdriver to remove the 13mm screw which is under and to the left of the power input.

  2. Using precision tweezers, remove the screw tab located on opposite side of the box. Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab. Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.
    • Using precision tweezers, remove the screw tab located on opposite side of the box.

    • Use a T9 Torx screwdriver to remove the 13mm screw revealed underneath the tab.

  3. Orient the case so that the front of the Xbox (the side with the power button) is facing you. Remove the top of the case by sliding the case towards you. Remove the top of the case by sliding the case towards you.
    • Orient the case so that the front of the Xbox (the side with the power button) is facing you.

    • Remove the top of the case by sliding the case towards you.

  4. Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing. Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel. Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.
    • Using a T9 Torx screwdriver, remove the two 15mm silver screws that are holding a circuit board/panel to the side of the interior metal casing.

    • Using the same screwdriver, remove the 9mm black screw located farther to the right on the same circuit board/panel.

  5. Remove the unscrewed panel from the side of the device by pulling it toward you. Be mindful of the connector, as it is fragile.
    • Remove the unscrewed panel from the side of the device by pulling it toward you.

    • Be mindful of the connector, as it is fragile.

  6. Using a Torx T9 screwdriver, remove the three gold  13.5mm screws holding on another side panel. Using a Torx T9 screwdriver, remove the three gold  13.5mm screws holding on another side panel. Using a Torx T9 screwdriver, remove the three gold  13.5mm screws holding on another side panel.
    • Using a Torx T9 screwdriver, remove the three gold 13.5mm screws holding on another side panel.

  7. iPhone Akku Fix Kits

    Nur $29.99

    Buy Now

    iPhone Akku Fix Kits

    Nur $29.99

    Buy Now
  8. Remove the panel by pulling it toward you. The panel will still be attached to the Xbox by a white connector, which is fragile.
    • Remove the panel by pulling it toward you.

    • The panel will still be attached to the Xbox by a white connector, which is fragile.

  9. Remove the white connector from the dislocated panel using precision tweezers. Do not force the connector out, as it is fragile. Wiggling may be necessary.
    • Remove the white connector from the dislocated panel using precision tweezers.

    • Do not force the connector out, as it is fragile. Wiggling may be necessary.

  10. On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws. Remove both of these 7mm screws with a Torx T9 screwdriver. Lift the detached plate off to the side.
    • On the top of the device in the corner directly above the white connector, there is an oval plate held in place by two screws.

    • Remove both of these 7mm screws with a Torx T9 screwdriver.

    • Lift the detached plate off to the side.

    • The plate is still connected to the device.

  11. Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case. Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.
    • Use a Torx T9 screwdriver to remove the six 47mm long screws, which attach the bottom side of the outer case.

  12. Turn the Xbox over, so that the bottom of the case is on top. Lift the bottom of the case off of the Xbox by pulling it up and toward you. Lift the bottom of the case off of the Xbox by pulling it up and toward you.
    • Turn the Xbox over, so that the bottom of the case is on top.

    • Lift the bottom of the case off of the Xbox by pulling it up and toward you.

  13. Flip over the device again, so that the top is facing upwards.
    • Flip over the device again, so that the top is facing upwards.

    • Remove the 11 remaining smaller 11mm screws on the metal casing using a Torx T9 screwdriver.

  14. Flip over the device again, so that the bottom is facing upwards. Using a Torx T9 screwdriver, remove the two screws located on opposite sides of the metal casing. One is near the fan vent, and the other is near the power supply vent.
    • Flip over the device again, so that the bottom is facing upwards.

    • Using a Torx T9 screwdriver, remove the two screws located on opposite sides of the metal casing. One is near the fan vent, and the other is near the power supply vent.

    • The left screw is 11mm and the right screw is 7.5 mm.

  15. Remove the metal casing by pulling it upward, revealing the interior components of the device. Remove the metal casing by pulling it upward, revealing the interior components of the device. Remove the metal casing by pulling it upward, revealing the interior components of the device.
    • Remove the metal casing by pulling it upward, revealing the interior components of the device.

  16. Lift and rotate the BD drive to reveal the wires that connect it to the motherboard. Lift and rotate the BD drive to reveal the wires that connect it to the motherboard. Lift and rotate the BD drive to reveal the wires that connect it to the motherboard.
    • Lift and rotate the BD drive to reveal the wires that connect it to the motherboard.

  17. Using your fingers, gently unplug the two sets of wires connecting the drive to the motherboard. The BD drive should now be completely detached from the rest of the device, and it can be set aside. The BD drive should now be completely detached from the rest of the device, and it can be set aside.
    • Using your fingers, gently unplug the two sets of wires connecting the drive to the motherboard.

    • The BD drive should now be completely detached from the rest of the device, and it can be set aside.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ashley Masuda

Mitglied seit: 24.01.2018

998 Reputation

7 Anleitungen geschrieben

Team

Cal Poly, Team S2-G6, Livingston Winter 2018 Mitglied von Cal Poly, Team S2-G6, Livingston Winter 2018

CPSU-LIVINGSTON-W18S2G6

4 Mitglieder

7 Anleitungen geschrieben

ok it says no other parts required besides the tweezers and the t9 screw driver, but it doesn't mention what model of BD-ROM is suitable to replace it with.

Chris Storey - Antwort

The six long screws actually take a T-10 bit

mthouchen - Antwort

Please FIX Number 8 THIS IS NOT RIGHT!

Unfortunately the manual is not correct here. Above the black slot is a white switch / pen, fold it over with your fingernail, so fold it over to the front. Then the cable can be easily removed without any problems and tweezers. GERMAN: Hier ist die Anleitung leider nicht korrekt. Oberhalb des schwarzen Steckplatzes befindet sich ein weißer Schalter/Stift, diesen mit dem Fingernagel umklappen, also praktisch zu der Vorderseite umklappen. Danach lässt sich das Kabel ohne Probleme und Pinzette einfach abziehen.

Marcel - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 14

Letzte 30 Tage: 61

Insgesamt: 656