Zum Hauptinhalt wechseln

Was du brauchst

Dieser Teardown ist keine Reparaturanleitung. Um dein HP LaserJet 1160 or 1320 zu reparieren, verwende unsere Fehlerbehebungsseite.

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 3 : Schritt 1, Bild 2 von 3 : Schritt 1, Bild 3 von 3
    • This teardown of the HP LaserJet 1320 is officially the first laser printer teardown on iFixit.

    • It took almost 7 hours to take apart this amazingly complex printer.

    • Spoiler alert: It's really nice to see something this repairable.

    • Also, check out the complete repair guide for this printer!

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • According to the service manual (there is a link in the documents section), the left cover of the printer can be opened without any tools by pulling on 2 tabs.

    • The service manual was right. For the record, this is actually easier than it sounds.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Now on to the formatter.

    • Remove 2 screws on the I/O port cover.

    • Remove 6 screws on the formatter cover.

    • Disconnect 3 connectors to the laser assembly, the cartridge connector, and the control panel.

    • Disconnect 2 flat flexible cables to the laser assembly and the control board.

    • While the service manual says not to use a PoziDriv screwdriver, I found that using a normal Phillips screwdriver on the screws in this printer would require excess force and damage the screws, but a PoziDriv screwdriver removed the screws without causing any damage.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 2 : Schritt 4, Bild 2 von 2
  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 1
  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • Removing the right cover is as easy as disengaging 3 tabs with the printer turned on its side.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • The back cover can be removed by removing 4 screws on the back of the printer.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 2 : Schritt 8, Bild 2 von 2
    • The duplexer tray can be removed by pulling outwards on the blue green blue-green tab, which releases the magnets that hold the tray in place.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 3 : Schritt 9, Bild 2 von 3 : Schritt 9, Bild 3 von 3
    • Remove 2 screws on the back of the printer, one on the left side, and one on the front.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 1
    • After disconnecting the control panel cable, the top cover can be removed.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 3 : Schritt 11, Bild 2 von 3 : Schritt 11, Bild 3 von 3
    • The control panel and its circuit board can easily be removed with a metal spudger.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 3 : Schritt 12, Bild 2 von 3 : Schritt 12, Bild 3 von 3
    • Remove one cable from the laser assembly.

    • Remove 4 screws from the laser assembly.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 3 : Schritt 13, Bild 2 von 3 : Schritt 13, Bild 3 von 3
    • After removing the cover and the clips holding in the lenses, the inside of the laser assembly can be seen.

    • The chip on the motor board is an AN44010A, most likely some sort of brushless motor driver, although no datasheet could be found.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 2 : Schritt 14, Bild 2 von 2
    • The board mounted on the side of the laser assembly contains the infrared laser diode and a photodiode to sense the beam direction. It has a chip marked as RH4-5444, for which no datasheet could be found.

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 15, Bild 1 von 2 : Schritt 15, Bild 2 von 2
    • Disconnect the fan cable from the control board on the back of the printer.

    • Remove the retaining clip from the fan.

    • Remove 2 screws holding in the fan.

    • While the fan can not be completely removed yet, this will make it easier to take apart other parts of the printer.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 16, Bild 1 von 3 : Schritt 16, Bild 2 von 3 : Schritt 16, Bild 3 von 3
    • Remove 1 screw from the top of the cartridge connector.

    • Remove 1 screw on the front of the cartridge connector.

    • The cartridge connector can be removed from the printer.

  17. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 17, Bild 1 von 2 : Schritt 17, Bild 2 von 2
    • The cable clip for the laser assembly cable can be removed from the chassis.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 18, Bild 1 von 2 : Schritt 18, Bild 2 von 2
    • Disconnect the duplexer cable from the control board.

    • Disconnect the duplexer solenoid cable from the duplexer PCB.

    • Remove one screw from the PCB and remove the PCB from the printer.

    • This tiny board contains 2 NPN transistors marked C2120 and C1815, which are used to drive the duplexer solenoid.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 19, Bild 1 von 3 : Schritt 19, Bild 2 von 3 : Schritt 19, Bild 3 von 3
    • Remove 3 screws on the duplexer gear assembly.

    • The duplexer gearbox can now be removed.

    • Remove one screw holding down the duplexer solenoid.

    • This appears to be a standard 24V open-frame solenoid, although no markings were found on it.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 20, Bild 1 von 3 : Schritt 20, Bild 2 von 3 : Schritt 20, Bild 3 von 3
    • Remove 3 screws to remove the safety interlock assembly.

    • Disconnect 2 spade connectors from the microswitch.

    • The safety interlock prevents the lasers or high-voltage power supply from being turned on when the cartridge door is open.

  21. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 21, Bild 1 von 3 : Schritt 21, Bild 2 von 3 : Schritt 21, Bild 3 von 3
    • The fan cable can now be derouted from the cable guide and the fan can be removed.

  22. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 22, Bild 1 von 1
    • The fan is a standard 24V brushless fan with a speed sensor manufactured by Nidec.

  23. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 23, Bild 1 von 3 : Schritt 23, Bild 2 von 3 : Schritt 23, Bild 3 von 3
    • Disconnect 2 cables from the control board.

    • Remove the gear from the fuser shaft.

    • Deroute the remaining cables in the cable guide.

  24. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 24, Bild 1 von 3 : Schritt 24, Bild 2 von 3 : Schritt 24, Bild 3 von 3
    • Remove 4 screws to remove the main gear assembly.

    • Remove 1 screw to remove the third solenoid.

  25. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 25, Bild 1 von 2 : Schritt 25, Bild 2 von 2
    • The cartridge door can be removed by removing 2 screws on the front of the printer.

  26. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 26, Bild 1 von 3 : Schritt 26, Bild 2 von 3 : Schritt 26, Bild 3 von 3
    • The pickup roller can now be removed by rotating the white tabs upwards and pulling them out.

  27. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 27, Bild 1 von 3 : Schritt 27, Bild 2 von 3 : Schritt 27, Bild 3 von 3
    • Remove 2 screws to remove the paper feed bar.

    • Remove 2 (hidden) screws to remove the registration assembly.

  28. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 28, Bild 1 von 2 : Schritt 28, Bild 2 von 2
    • Remove one gear on the output shaft of the fuser.

  29. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 29, Bild 1 von 3 : Schritt 29, Bild 2 von 3 : Schritt 29, Bild 3 von 3
    • Disconnect the cable to the tray connector and route it through the hole in the chassis.

    • You are now halfway through the teardown.

  30. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 30, Bild 1 von 3 : Schritt 30, Bild 2 von 3 : Schritt 30, Bild 3 von 3
    • Disconnect 2 cables from the control board and remove them from the cable guide.

  31. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 31, Bild 1 von 2 : Schritt 31, Bild 2 von 2
    • Remove the cable guide from the chassis.

  32. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 32, Bild 1 von 3 : Schritt 32, Bild 2 von 3 : Schritt 32, Bild 3 von 3
    • Remove the cable guide on the other side of the chassis.

    • Disconnect 2 connectors from the control board.

  33. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 33, Bild 1 von 2 : Schritt 33, Bild 2 von 2
    • Disconnect the high voltage wire from the fuser.

  34. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 34, Bild 1 von 3 : Schritt 34, Bild 2 von 3 : Schritt 34, Bild 3 von 3
    • Deroute the tray connector cable through the cable guide.

    • Disconnect the main motor cable.

  35. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 35, Bild 1 von 2 : Schritt 35, Bild 2 von 2
    • Remove 3 screws from the right side of the printer.

    • Remove 3 screws from the left side of the printer.

  36. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 36, Bild 1 von 1
    • The fuser can now be removed from the printer.

  37. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 37, Bild 1 von 3 : Schritt 37, Bild 2 von 3 : Schritt 37, Bild 3 von 3
    • Remove one screw on the front of the fuser.

    • Remove one screw on the top of the fuser.

    • The paper output assembly can now be removed.

  38. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 38, Bild 1 von 2 : Schritt 38, Bild 2 von 2
    • Remove one spring and one screw from each side of the fuser.

  39. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 39, Bild 1 von 2 : Schritt 39, Bild 2 von 2
    • Remove the large springs at each side of the fuser by pushing in on the plastic inserts.

    • The springs will fly out violently if you do not hold them with pliers.

    • Remove one screw on the fuser.

  40. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 40, Bild 1 von 2 : Schritt 40, Bild 2 von 2
    • Remove the metal piece held down by the spring on each side of the fuser.

  41. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 41, Bild 1 von 1
    • The fuser roller can be removed from the printer.

    • The white wires on the left connect to a temperature sensor.

    • The large connector on the right connects to the heating element and a thermal fuse.

  42. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 42, Bild 1 von 3 : Schritt 42, Bild 2 von 3 : Schritt 42, Bild 3 von 3
    • Disconnect the snap-on connector from the right side of the fuser roller.

    • The heating element can be removed from its channel in the roller.

    • The heating element is a 576-watt thick film ceramic heater.

  43. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 43, Bild 1 von 3 : Schritt 43, Bild 2 von 3 : Schritt 43, Bild 3 von 3
    • Remove the plastic clip from both sides of the roller.

    • The fusing film can be slid off of the roller without the clips in the way.

  44. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 44, Bild 1 von 3 : Schritt 44, Bild 2 von 3 : Schritt 44, Bild 3 von 3
    • After removing the metal cover, the temperature sensor (red) and the thermal fuse (orange) can be removed.

    • The wires on both of these components have very thick silicone insulation to protect from heat.

  45. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 45, Bild 1 von 2 : Schritt 45, Bild 2 von 2
    • After removing the plastic clip, the soft foam pressure roller can be removed.

    • The metal rod in the roller allows the roller to be negatively charged, which prevents toner from sticking to the fusing film. Each end of the rod is coated in a conductive black liquid which helps it make contact with the high-voltage connector.

  46. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 46, Bild 1 von 3 : Schritt 46, Bild 2 von 3 : Schritt 46, Bild 3 von 3
    • Remove 2 screws to remove the metal bar from the fuser.

    • After removing one screw, this small circuit board can be removed.

    • The board contains a beam interrupt sensor, which contains an infrared LED pointing at an infrared phototransistor. When an object enters the slot and breaks the beam, the phototransistor detects it as a drop in infrared light.

  47. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 47, Bild 1 von 3 : Schritt 47, Bild 2 von 3 : Schritt 47, Bild 3 von 3
    • Remove 4 screws on each side of the printer to remove the metal midframe piece that holds the chassis together.

    • The massive control board can now be seen.

  48. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 48, Bild 1 von 2 : Schritt 48, Bild 2 von 2
    • Remove the metal feed plate from the paper feed mechanism.

  49. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 49, Bild 1 von 2 : Schritt 49, Bild 2 von 2
    • Remove the tray connector and motor cables from the cable guide.

    • The high voltage corona wire used to apply a charge to the paper is visible in the right of these pictures (the spiked metal strip attached to the paper feed assembly)

  50. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 50, Bild 1 von 3 : Schritt 50, Bild 2 von 3 : Schritt 50, Bild 3 von 3
    • Remove one screw holding down the tray connector cable guide and then remove the cable guide.

    • Remove one screw on the printer chassis.

  51. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 51, Bild 1 von 3 : Schritt 51, Bild 2 von 3 : Schritt 51, Bild 3 von 3
    • Remove 2 screws from the left side of the chassis.

    • Push the safety interlock and formatter cables through the hole in the chassis.

  52. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 52, Bild 1 von 3 : Schritt 52, Bild 2 von 3 : Schritt 52, Bild 3 von 3
    • Bend the chassis to allow the control board to come loose, and disconnect the 2 cables to the paper feed assembly to remove the control board.

  53. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 53, Bild 1 von 1
    • Remove 4 screws on the control board to remove it from the metal plate.

  54. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 54, Bild 1 von 1
  55. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 55, Bild 1 von 1
    • Chips on the back of the board:

    • STMicroelectronics 324 E9SU518 - Possibly an LM324 Quad Op Amp?

    • STMicroelectronics 339 E9W2513 - Possibly an LM339 Quad Comparator?

    • Unidentified Texas Instruments chip with the part number sanded off.

    • A2714 Power MOSFET

    • Large QFP chip with the part number sanded off and a red and a blue mark on top.

    • Interestingly, all the chips were covered in a clear coating that made it hard to read the part numbers.

    • It appears that whoever designed this board was trying to prevent reverse engineering by making it hard to read the part numbers on the chips.

  56. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 56, Bild 1 von 2 : Schritt 56, Bild 2 von 2
    • The main motor can be removed after unclipping the cable guide and removing 3 screws.

  57. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 57, Bild 1 von 2 : Schritt 57, Bild 2 von 2
    • The motor is a Nidec RK2-0419, which appears to be appears to be a fairly powerful "outrunner" style brushless motor rated for 1.3A at 24V. The rotor (the round metal part) is about 3 inches in diameter and the entire motor weighs about 15 ounces.

    • This motor might be a special motor designed for use in this printer, as it and many other components have a number with the format RK2-0xxx on them.

    • The single chip on the motor is a BD6761FS Brushless Motor Driver.

    • At this point, all that is left of the printer is the metal chassis and the paper feed assembly, a large chunk of plastic containing 2 more beam interrupt sensors.

  58. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 58, Bild 1 von 1
    • This printer receives a perfect repairability score of 10/10.

    • No adhesives, thermoplastic staking, spot welding, or rivets are used.

    • Service manuals for this and most HP printers are easy to find and free.

    • Replacement parts are easy to find.

    • Printer is designed to be repaired.

Angehängte Dokumente

jdp23

Mitglied seit: 08/22/13

1.302 Reputation

23 Anleitungen geschrieben

6 Kommentare

Looks like someone got a much longer teardown already :)

Monroe KA Teardown

masterX244 - Antwort

Excellent. I needed to see the polygon mirror of the LSU. It proved it’s too thin for my DIY project so you save me $12 for buying such unit from China

net_xplorer - Antwort

Hi Sir.

Sir, im facing both sides paper jam problem in hp 1320n printer.

Actually when the paper goes in the printer for printing the second side, at that time it blocks.

Kindly guide me.

Thanking you

abbas khan - Antwort

The first thing I would do is strip it down to the level of the “duplex tray” as shown above, and inspect that, clean it and clean all the rollers with isopropyl alcohol. See if that helps!

Chris Kear -

Thanks for this teardown. It saved me hours resurrecting a printer I received as a gift. I’m impressed by the build quality of this printer. It’s like a brick outhouse, heaps of steel, and everything modular, with servicing in mind. Should last forever, since I can always fix it, thanks to you!!

Chris Kear - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 3

Letzte 7 Tage: 24

Letzte 30 Tage: 80

Insgesamt: 16,950