Einleitung

This is the teardown for the original Microsoft Xbox, not the Xbox 360.

Dieser Teardown ist keine Reparaturanleitung. Um dein Xbox zu reparieren, verwende unsere Fehlerbehebungsseite.

Start with your Xbox unplugged and sitting on a flat, stable surface.
  • Start with your Xbox unplugged and sitting on a flat, stable surface.

Kommentar hinzufügen

Flip the Xbox over and pry off the rubber feet with a metal spudger.
  • Flip the Xbox over and pry off the rubber feet with a metal spudger.

Kommentar hinzufügen

  • Peel back both the silver sticker and the white barcode sticker to reveal two additional screws.

Kommentar hinzufügen

  • Use a T20 Torx screwdriver to remove the four screws located under the rubber feet you just removed as well as the two screws from beneath the stickers removed in the previous step.

Kommentar hinzufügen

  • Use a metal spudger to pry the side of the top shell away from the bottom of the Xbox.

  • Use your fingers to lift the bottom shell of the Xbox away from the top shell.

  • It may be helpful to have a second person lift the bottom shell off while you pry the edges of the top shell away from the bottom shell.

Kommentar hinzufügen

  • Once the bottom shell is no longer attached, carefully turn the Xbox right-side-up and lift off the top shell.

Kommentar hinzufügen

  • Move the grey ribbon cable out of the way in order to remove the three 3 mm screws using T10 Torx screwdriver. They are located on the upper right corner, lower right, and lower left corners of disk drive.

  • The screw on the lower left corner of the disk drive is not in the hole that it appears to be in, but rather just closer to the corner.

Kommentar hinzufügen

  • Lift the hard drive storage unit out of the Xbox. It should come right out.

  • Take the power cable out of the track around the hard drive so that the unit will come out easier.

Kommentar hinzufügen

  • Use a T15 Torx screwdriver to remove four 3.37mm screws from both sides of the hard drive.

  • Remove the plastic housing from the hard drive. It does have some clips on it, but it should come right off.

Kommentar hinzufügen

  • Unplug both the ribbon cable and power cable from hard drive.

  • They are in there pretty tightly, so this may take some effort.

how do i do the wires

elijah ross - Antwort

that was very hard

elijah ross - Antwort

  • Remove the disk drive. It should come right out.

  • Unplug the ribbon cable and yellow cables from back of disk drive.

Kommentar hinzufügen

  • Pry back the black plastic tabs around the disk drive in order to remove it from its housing. Once removed, set the drive aside.

Kommentar hinzufügen

  • Unplug the multi-colored power cord from the motherboard. It can be plugged in very tight, so it may take some effort to unplug it.

Kommentar hinzufügen

  • Using T10 Torx screwdriver, remove two 3mm screws from the power supply board.

Kommentar hinzufügen

  • Remove the power supply and set it aside. It should lift right out.

Kommentar hinzufügen

  • Unplug the bundle of yellow cables as well as the rainbow cord from the motherboard.

Kommentar hinzufügen

  • Remove eleven 3mm screws from motherboard, using a T10 Torx screwdriver. Refer to the picture to find all eleven.

  • Unplug the power cable attached to the fan.

Kommentar hinzufügen

  • Remove the motherboard from the Xbox. As long as all of the screws are out and the fan is disconnected, it will lift out easily.

Kommentar hinzufügen

  • Pry the plastic fan clips away from the fan base and remove the fan.

  • This may take a little effort, as the clips are pretty stiff. Beware, the fan will be filthy.

Kommentar hinzufügen

  • Using a T10 Torx screwdriver, remove two 3mm screws from each of two controller sockets.

  • Take the sockets out by pulling back and up at the same time.

Kommentar hinzufügen

  • Congratulations, your Xbox is now completely dismembered.

Kommentar hinzufügen

rmarstel

Mitglied seit 29.10.2009

3.601 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team 18-2, Maness Fall 2009 Mitglied von Cal Poly, Team 18-2, Maness Fall 2009

CPSU-MANESS-F09S18G2

3 Mitglieder

10 Anleitungen geschrieben

Awesomeness, thanks a lot!

godoyander - Antwort

Thanks a million - perfect!

xan_lucky16 - Antwort

Heatsink removal?

Matt Russell - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 22

Letzte 7 Tage: 157

Letzte 30 Tage: 780

Insgesamt: 72,566