Was du brauchst
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
To start the teardown, remove the two screws near the bottom.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use a suction cup to pull of the screen.
-
Hint: Be careful, as you do not want to pull out any wires.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Now remove the bracket encasing the screen cables.
-
Remove all of the screws surrounding the metal plate.
-
Use a plastic spudger to remove the metal plate once unscrewed.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Disconnect the cables that attach the screen to the board.
-
Then simply pull the screen away from the base.
-
Make sure that all connectors have been disconnected.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Disconnect the battery from the device.
-
First, remove the 3 screws above the battery connector.
-
Use a plastic spudger to remove the metal plates.
-
Take the battery connector out of its socket.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the SIM card with a paper clip or a SIM card ejector.
-
Push your paper clip or SIM card ejector into the small hole on the right side of your device.
-
Push as hard but as gently as possible until it starts to come out. Then use your fingers to take it the rest of the way out.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the metal cover near the camera module to reveal the screw and camera connectors
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the connector next to the camera from its port and then lift the camera module away from the phone.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the screws surrounding the IO board in all locations.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Take out the screws surrounding the power port.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Find each cable within these 3 pictures and carefully take them off of the IO board.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Unscrew the screw holding onto the vibrator.
-
Pry the vibrator off with a plastic spudger.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Start to pull up the adhesive parts of the IO board.
-
Slowly remove the main parts of the IO board.
-
Unscrew any screws that are stopping you from completely taking the IO board out.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
And now you're finished!
-
For reassembly, follow these steps in reverse order.
-
This tear down was a lot of fun for me and my team member. We learned a lot about the inside of the iPhone 5 and everything went according to plan. Next time, we want to actually fix a problem to get it working again.
-
2 Kommentare
No screw sizes and their places... NO NOTHING
Hey there! This guide has been archived, which means we have a more complete version of the guide. Keep in mind is a user submitted teardown, not a repair guide. Teardowns are meant to be an exploratory look into a device, and should absolutely not be followed for repair or replacement. We have tons of step-by-step guides for the iPhone 5, check out the device page!