Einleitung

This guide will instruct you on how to replace a cracked or damaged LCD screen and digitizer assembly in your LG G4 smartphone.

It may be necessary to use a pre-cut LG G4 adhesive strip or Tesa 61395 tape to secure your new screen to your device.

  1. Make sure the phone is powered off.
    • Make sure the phone is powered off.

    • Remove the rear cover by placing the plastic opening tool in the groove on the bottom left side of the LG G4 and gently prying up.

  2. Place the plastic opening tool at the bottom edge of the battery and lift up. Carefully remove battery with your hands. Place the plastic opening tool at the bottom edge of the battery and lift up. Carefully remove battery with your hands.
    • Place the plastic opening tool at the bottom edge of the battery and lift up. Carefully remove battery with your hands.

  3. Remove the eleven 3.9 mm Phillips #00 screws found at the back of the phone. Remove the eleven 3.9 mm Phillips #00 screws found at the back of the phone. Remove the eleven 3.9 mm Phillips #00 screws found at the back of the phone.
    • Remove the eleven 3.9 mm Phillips #00 screws found at the back of the phone.

  4. Once all the screws have been removed, place the plastic opening tool in the lower left corner and firmly lift the cover up. Detach the cover with your fingers Detach the cover with your fingers
    • Once all the screws have been removed, place the plastic opening tool in the lower left corner and firmly lift the cover up.

    • Detach the cover with your fingers

  5. Remove the following four press-fit connectors with the flat edge of a plastic spudger or opening tool: Front-facing camera connector.
    • Remove the following four press-fit connectors with the flat edge of a plastic spudger or opening tool:

    • Front-facing camera connector.

    • Rear-facing camera connector.

    • Digitizer connector.

    • The rear-facing camera may be held down to the frame with two sided tape. Try to move the camera with the spudger prior to lifting the motherboard If it does not budge, use the same tool to pry it from the frame to avoid damaging the connector cable in the next step.

    There is a ribbon on the left of the camera. Use spudger to lift this so that the camera is left behind. Do not fiddle with the rear facing camera.

    befetti - Antwort

    I second that! Just unsnap the camera connector like the other two. Unsticking the camera instead is silly, when that is so much simpler. Please update this to mark the third connector to be unsnapped.

    Eric Schwarzenbach - Antwort

    I lifted the ribbon but I can't get it to stick back down!

    Jeff Elliotson - Antwort

    I tried lifting the ribbon but it didn't unsnap… it actually felt like it ripped off. I couldn't get it to “snap” back down like the other ones.

    Jeff Elliotson - Antwort

  6. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  7. Remove the motherboard by lifting it up using the plastic opening tool and your fingers . Remove the motherboard by lifting it up using the plastic opening tool and your fingers .
    • Remove the motherboard by lifting it up using the plastic opening tool and your fingers .

    My LG G4 has stopped working. Was told it needs board replacement. How do I get the motherboard. I reside in Nigeria.

    Niyi Adedokun - Antwort

    • Use a heat gun over the auxiliary port to soften the adhesive that secures it to the plastic housing.

    • Insert a nylon spudger into the auxiliary port and gently pry upward to free the port.

    • Use a pair of tweezers to remove the adhesive strip that secures the digitizer ribbon cable.

  8. Insert the flat side of a nylon spudger below the digitizer ribbon cable to free it from the adhesive. You may use your fingers to pull the ribbon cable gently as you free the panel from the adhesive with the spudger. It may be necessary to apply more heat if the adhesive is still too strong.
    • Insert the flat side of a nylon spudger below the digitizer ribbon cable to free it from the adhesive.

    • You may use your fingers to pull the ribbon cable gently as you free the panel from the adhesive with the spudger. It may be necessary to apply more heat if the adhesive is still too strong.

  9. Use a heat gun or an iOpener to soften the adhesive underneath the edges of the screen. Use a heat gun or an iOpener to soften the adhesive underneath the edges of the screen.
    • Use a heat gun or an iOpener to soften the adhesive underneath the edges of the screen.

    • Use a heavy duty suction cup and firmly pull the screen away from the frame to create a small gap.

    • There is a very thin strip of adhesive that holds the screen to the frame; this step should not require excessive force. Apply additional heat along the edges of the phone if the screen is difficult to free.

    • Insert a plastic opening pick into the gap between the screen and the plastic housing.

    • Slide the plastic opening pick along the border of the screen to break any additional adhesive and free the screen assembly.

  10. Remove the LCD screen & digitizer assembly. Feed the digitizer ribbon cable gently through the frame. Feed the digitizer ribbon cable gently through the frame.

    It is possible replace the digitalizer only?

    Nene indy - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

17 weitere Nutzer haben diese Anleitung absolviert.

Richard Suovanen

Mitglied seit: 07.02.2017

13.408 Reputation

10 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

100 Mitglieder

7.962 Anleitungen geschrieben

It is possible replace the digitalizer only? Thanks

Nene indy - Antwort

Per the LG G4 Teardown guide, the glass, digitizer, and LCD are all fused together, so you have to replace the whole assembly

Eric Clothier - Antwort

Statistik anzeigen:

Letzte 24 Stunden: 7

Letzte 7 Tage: 78

Letzte 30 Tage: 322

Insgesamt: 16,410