Einleitung

Hier wird der Austausch des Trackpads gezeigt.

  • Bevor du anfängst, fahre dein Gerät herunter. Schließe das Display und lege es umgekehrt auf eine weiche Oberfläche.

  • Entferne die folgenden zehn Schrauben:

    • Zwei 9 mm Pentalobe P5 Schrauben

    • Acht 2,6 mm Pentalobe P5 Schrauben

  • Der Spezialschraubenzieher, der zum Entfernen der zehn 5-Punkt Pentalobe Schrauben benötigt wird, ist hier erhältlich.

These pentalobe screw sizes can't possibly be right - not even close. Should they perhaps be 0,8 mm and 1,2 mm?

Rulle Boer - Antwort

The screw sizes refer to the length of the shaft, not the diameter of the head or socket. P5 is the standard pentalobe size for all these screws, regardless of length.

I agree that the notation is a little confusing. I think it's because, with standard sized hardware like for your house, you have shaft diameter (say 1/8" or 3mm) and shaft length (say 3" or 7.5cm). So we're programmed to think of small numbers like that as diameter. But in this case, they're length.

budpegasus - Antwort

Pulling the fan cable out was terrifying but you actually just pull on the cable itself. No way to get any leverage at the connector to dislodge it. Did come out easily but like I said, scared me!

allison - Antwort

Draai de schroefjes voorzichtig los en leg ze op een stabiele plek neer en let erop dat de schroefje een verschillende lengte hebben.

bwgvanderveer - Antwort

I thought I could replace my 256 Gb SSD with 512? regards

ola m - Antwort

Do you have good Test Point Voltages? It appears there are silver colored Test points on the I/O Board. I am working on a water spill and trying to troubleshoot if both the I/O board and the Logic need replaced.

andrew - Antwort

It's probably not necessary but may be a little safer to completely discharge the old battery before replacing it.

Larry Smith - Antwort

tell a model that was not inferior to the speed of the one in the laptop.

Thank you

ilyabuhov - Antwort

Do i need to order tools separately to replace the battery i just ordered?

anne uhlir - Antwort

im looking for a Logic Board for a

Apple - MacBook Air® - 13.3" Display - Intel Core i5 - 8GB Memory - 128GB Flash Storage (Latest Model) - Silver Model: MQD32LL/A

Any help is appreciated.

Jamie Comstock - Antwort

Löse das hintere Gehäuse vom Air, indem du mit den Fingerspitzen zwischen Display und Gehäuse gehst und es nach oben ziehst.
  • Löse das hintere Gehäuse vom Air, indem du mit den Fingerspitzen zwischen Display und Gehäuse gehst und es nach oben ziehst.

  • Entferne das hintere Gehäuse und lege es beiseite.

There is a nub on the inside of the case which is attached to the battery. When you try to pull it open, it appears to be attached to the plastic casing of the battery, which sometimes splits. I gently unhooked the nub from the battery before removing the case fully. This seems to happen if the battery has suffered some drop damage (plastic parts broken around screws and parts of plastic frame split). Just an FYI in case your lower case doesn't pull away easily.

Jeannie Crowley - Antwort

When closing this back up make sure that the antenna cable is tucked away neatly

Gabriel - Antwort

Ziehe die Plastiklasche, die am Stecker des Akkus hängt, in Richtung der vorderen Ecke des MacBooks, um den Akku vom Logic Board zu trennen. Der Stecker darf nicht nach oben gezogen werden, während du ihn vom Anschluss trennst.
  • Ziehe die Plastiklasche, die am Stecker des Akkus hängt, in Richtung der vorderen Ecke des MacBooks, um den Akku vom Logic Board zu trennen.

  • Der Stecker darf nicht nach oben gezogen werden, während du ihn vom Anschluss trennst.

The guide says: "Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board", but the battery model that I was replacing did not have a clear plastic pull tab at all...

The battery model shown in this guide is: A1405

I was installing battery model: A1406

A1406 has the following connector:

Top:

http://www.directupload.net/file/d/4122/...

Bottom:

http://www.directupload.net/file/d/4122/...

By looking at the bottom of the new battery I saw how it could be removed. Simply by a gentle upward movement. I very, very carefully nudged it a bit upwards using a screwdriver on the left and right side, as shown here:

http://www.directupload.net/file/d/4122/...

It came out fairly easy, luckily!

(And yes, I also cleaned up this MacBook before closing it again. It was a bit hairy in a literal way. Electronics and pets is not the best combination. ;-) )

This was a great guide!

wil - Antwort

I think you may have been reading the wrong guide by mistake.

Looking at the various MacBook Air battery replacement guides, all of the 13" models show the connector depicted in this guide. All of the 11" models (e.g. MacBook Air 11" Mitte 2012 Akku austauschen) show a connector like the one in your photos.

shamino -

The 13 inch's tab is a bit more difficult to reinstall than uninstall. Delicate care is needed.

Andrew Ruble - Antwort

I agree with Andrew and Joes. I also found that the trickiest part was to pull the tap back when reinstalling the new battery. A special hint at this point in the guide would be nice.

Alexander Kluge -

This is the tricky part if there is one. Just pull back towards the battery and not up.

Joe Wasser - Antwort

hello there, My macbook air does not recognize a battery connected, anymore.

It looks like I damaged the connectors while trying to connect the battery back, although it does not look damaged. I must say, I tried a little force to squeeze the connector in the middle instead of the edge. May have damaged the connector ?

Once, after this, the MBA recognized my battery when pressed the connectors edge to the pins on the board. However, this did not last long and my MBA does not recognize the battery anymore. Any solutions on how I can fix this ? Please help.

Samy Palaniappan - Antwort

Had the same issue where my Macbook did not recognize the battery on the first try. I opened it back up and re-seated the connector and that fixed the problem. That particular connector does not seem to have a positive engagement. It does not appear to seat all the way down. It’s charging now and I hope it will remain stable and connected as I travel.

Paul Tornatta - Antwort

Entferne die folgenden fünf Schrauben, die den Akku am Gehäuse befestigen:
  • Entferne die folgenden fünf Schrauben, die den Akku am Gehäuse befestigen:

    • Drei 6,3 mm Torx T5 Schrauben

    • Zwei 2,4 mm Torx T5 Schrauben

Les couleurs ne me semblent pas justes.

drixe - Antwort

The screw heads are made of a soft butter like chinese metal and will easily get f*cked up. take care when reinstalling to not mess them up.

John Hamilton - Antwort

les couleur sont justes; die rot markierten Schrauben oben und mitte sind länger als die unteren.

I had used the P5 driver there, too (just gently put the bit into the screws and see that’ll fit.

jmhoraze - Antwort

Achte darauf, den Akku nicht zu quetschen und die vier Polymer-Zellen möglichst nicht zu berühren.
  • Achte darauf, den Akku nicht zu quetschen und die vier Polymer-Zellen möglichst nicht zu berühren.

  • Hebe den Akku von der Seite des Logic Boards aus an und entferne ihn vorsichtig aus dem Gehäuse.

Quick note about the replacement battery, if you bought from iFixit and the battery sections have a thin film over them, peel them off. They're to protect the battery during transit, and if you leave them on they might cause heating issues.

Here is a link to my question about it: Replacement battery has thin film on each section do I need to remove? plus, I just got an email from iFixit customer support that it needs to be removed.

dpchoung - Antwort

thank you for the help! I installed the proper batt properly following the advice from here;-) Mahalo from Hawaii-

zzzikaikazzz - Antwort

Does replacement battery for Macbook Air 13" Mid 2012 works with Mac OS Sierra 10.12.3 and up?

Benny Forsberg - Antwort

I installed the battery (OEM Apple) for the Mac Air 2013 throygh 2015:

1. the battery for the Mac Air 2012 throygh 2015 was stated to may have compatibility problems;

2. lesser price;

no problems with macOS Sierra.

jmhoraze - Antwort

Replaced it in no time! Thank you and cheers from Slovenia (that’s the one who beat you in hockey few days ago

Mark Ogner - Antwort

Klappe den Sicherungsbügel am ZIF Anschluss des Flachbandkabels zum Trackpad mit der Spudgerspitze oder deinem Fingernagel hoch. Achte darauf, dass du nur am scharnierartigen Sicherungsbügel hebelst, (gegenüber dem Kabel) nicht  am Anschluss selbst.
  • Klappe den Sicherungsbügel am ZIF Anschluss des Flachbandkabels zum Trackpad mit der Spudgerspitze oder deinem Fingernagel hoch.

  • Achte darauf, dass du nur am scharnierartigen Sicherungsbügel hebelst, (gegenüber dem Kabel) nicht am Anschluss selbst.

  • Ziehe das Flachbandkabel zum Trackpad gerade aus seinem Anschluss in Richtung der hinteren Kante des Air.

Thanks for this fantastic guide!!! Got an old Macbook Air working again. Only difficult spot was the ZIF cables. Man, I hate ZIF cables....

lyleberman - Antwort

I found it easyer to first connect the cables to the touchpad during reassabling. I could handel the tiny connectors better. After connecting the cabels I could easiely install the touchpad it self.

Stefan Kania - Antwort

Hebe das Flachbandkabel zur Tastatur mit einer Hand an und klappe gleichzeitig den Sicherungsbügel am ZIF Anschluss des Tastaturkabels mit der Spudgerspitze oder deinem Fingernagel hoch. Achte darauf, dass du nur am scharnierartigen Sicherungsbügel hebelst, nicht  am Anschluss selbst.
  • Hebe das Flachbandkabel zur Tastatur mit einer Hand an und klappe gleichzeitig den Sicherungsbügel am ZIF Anschluss des Tastaturkabels mit der Spudgerspitze oder deinem Fingernagel hoch.

  • Achte darauf, dass du nur am scharnierartigen Sicherungsbügel hebelst, nicht am Anschluss selbst.

  • Ziehe das Flachbandkabel zur Tastatur gerade aus seinem Anschluss heraus in Richtung der Vorderkante des Air.

Kommentar hinzufügen

Entferne folgende zwölf Kreuzschlitzschrauben:
  • Entferne folgende zwölf Kreuzschlitzschrauben:

    • Sechs 1,6 mm Schrauben, welche das Trackpad am oberen Gehäuse befestigen.

    • Sechs 1,6 mm Schrauben, welche die Halterungen des Trackpads am Trackpad befestigen.

    • Ein PH000 Kreuzschlitzschraubendreher sollte gehen, aber ein JIS000 funktioniert genauso gut.

I stripped one of the six 1.6mm screws securing the trackpad to the upper case. Where could I get a replacement and what are the exact dimensions (I assume that 1.6mm is the length not the head size). Not sure whether this is the right place to post this, but I would be very thankful for some help.

Karl - Antwort

The 00 philips driver is not working for these 6 screws...very frustrated....

Adam - Antwort

The 00 phillips screw driver does not do the job for step 8!!!!!!!!! FRUSTRATING!

anonymous 1446 - Antwort

Anyone figured the right screwdriver?

er09gi4v - Antwort

Worst part was the philips screws on the brackets, step 8. One screw wouldn't unscrew for the longest time. I stripped it so bad, that I finally got it undone with a Torx 5 that I wedged into the stripped screw hole! Fortunately the replacement trackpad came with it's own brackets and screws anyway, so I didn't need to re-use the messed up screw.

In the end, success...phew!

fauxryan - Antwort

Beware that when you remove these screws the trackpad will have dropped down and resting on the screen. Maybe a precaution would be to place a thin cloth between the trackpad and screen.

Joe - Antwort

Agreed on the error in the guide. J00 seems to be the best fit.

H4nd5omeR0b - Antwort

I stripped one of the 12 screws. Of course one of the ones attached to the unibody frame not the trackpad. I thought I could weasel the trackpad out without taking the right bracket off but no dice. I had to bend the bracket and turn it around to get the trackpad out.

After I got the trackpad out I took out the replacement (purchased from here) and lo and behold it had the two brackets attached! So great, I'm good on screw count! But crap, now I REALLY need to get that stripped screw back out.

Thankfully I was able to dig it out with a tiny flat head bit from the 54 bit driver kit.

I even reattached the two brackets to the old trackpad and put it back in the ESD bag. I wonder if I can send it back to iFixIt to be refurbished. Don't want to toss it and have it wind up in a landfill unnecessarily!

David Lam - Antwort

The Phillips 00 I bought from iFixit definitely doesn't work. Gonna try their 000.

jorach - Antwort

My new trackpad came with the brackets installed. It wasn’t necessary for me to remove the screws circled in orange (they hold the bracket to the trackpad). Check to see if your new trackpad has the brackets installed before removing the orange screws.

Doug Weathers - Antwort

After purchasing multiple sets of drivers to get these out, I recommend anyone who finds they don’t have an adaquet PH00 driver to skip any dollar store or RadioShack driver sets. Head down to your local tool shop or auto repair store and buy yourself a $5-$10 set of precision drivers with only a few bits. Don’t go buying yourself a 20 piece set and think you’re getting a deal, these screws require a good quality PH00 to be removed without stripping.

Spencer Shupe - Antwort

Entferne die rechte und die linke Halterung des Trackpads vom oberen Gehäuse.
  • Entferne die rechte und die linke Halterung des Trackpads vom oberen Gehäuse.

Kommentar hinzufügen

Entferne die 1,4 mm Torx T5 Stellschraube aus der vertieften Öffnung nahe der Vorderkante des oberen Gehäuses.
  • Entferne die 1,4 mm Torx T5 Stellschraube aus der vertieften Öffnung nahe der Vorderkante des oberen Gehäuses.

  • Ziehe beim Zusammenbau diese Schraube nicht zu stark an, sonst hört die Taste ab einem bestimmten Punkt auf zu klicken. Justiere die Schraube so, bis die bewegliche Seite des Trackpads minimales Spiel hat.

This was a T10 on my Mid 2011.

Joe - Antwort

Sorry, seems more like a T6

Joe -

This was a T6 on mine as well. Sadly I figured that out after threading the screw with the T5 included in the iFixit kit, so now my trackpad won't click at all.

IMPORTANT NOTE: Buy a T6 screwdriver if the T5 in the kit is just a bit too small for the screw in step 10.

Jon -

I thought the purpose of this set screw was to adjust the height of the pad relative to the rest of the deck. By feeling underneath as I adjusted this screw, I was able to get the join between the pad and the deck seamlessly level,

bbc2 - Antwort

Hi, I just want to ask what it means that it will stop clicking eventually, I had my macbook air trackpad replaced after some water fell on it and now around 9 months later the trackpad click gets stuck and it's driving me crazy, I went back to the service center myself and the technician actually admitted that he overtightened the screws but since the parts warranty is only 90 days he has to charge me again. So my question actually is can overtightening it cause permanent damage? Is there anything I can do? There's no apple store here (Cyprus) but the service center is one of the official service and registered distributor for Mac products and specifically for the more professional clientele.

crossmission1984 - Antwort

can anyone tell me where to get a replacement for the set screw mentioned in step 10? mine has gone missing. all i need is the screw, i don't want to replace the whole trackpad.

sean - Antwort

I, too, have a question about the set screw. I replaced a MacBook Air 2011 keyboard because of water damage and that process involves also taking out the trackpad and putting it back in. After reassembly, I now get phantom clicks (the "click" sound happens as expected, but the Air frequently thinks I'm clicking when I'm not). Could this be a result of over/under tightening the set screw, or is it more likely the trackpad also needs replacement?

Hank - Antwort

The set screw on my macbook barely turns 1/8 of a rotation before it hits a blockage. I do not want to try to turn harder for fear of stripping the screen and/or the threads in the case. I assumed that the screw should be able to be completely unscrewed from the case, correct? Any idea what's causing the blockage?

johnkowtko - Antwort

There is no need or benefit to removing this screw completely. Maybe back it out a little bit just to make it easier to install the new trackpad, and then adjust it once the new trackpad is mounted in the case. Agreed, this was a T6 on my MacBook Air 13" Mid 2012.

mattdittrich - Antwort

Hebe die Kante des Trackpads nahe der Tastatur vorsichtig mit dem flachen Ende des Spudgers aus ihrer Vertiefung im oberen Gehäuse, indem du sie aus den Halterungen, die am oberen Gehäuse angebracht sind, weghebst. Entferne das Trackpad vom oberen Gehäuse.
  • Hebe die Kante des Trackpads nahe der Tastatur vorsichtig mit dem flachen Ende des Spudgers aus ihrer Vertiefung im oberen Gehäuse, indem du sie aus den Halterungen, die am oberen Gehäuse angebracht sind, weghebst.

  • Entferne das Trackpad vom oberen Gehäuse.

Kommentar hinzufügen

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

45 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Brittany McCrigler

Mitglied seit 05.03.2012

78.110 Reputation

431 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

117 Mitglieder

5.752 Anleitungen geschrieben

The Apple tech repair guide for this model of Macbook Air states that the flexures use Phillips #000 screws, but I didn't have good luck using #000 drivers on them. A high quality precision Phillips #00 driver worked a little better, but I'm wondering if this is actually a JIS cross point phillips #00 or #000 screwdriver? The screws look more like JIS (Japanese Industry Standard) instead of Phillips, anyone try a JIS with better luck on these?

iphonetechtips - Antwort

Yes..I did, and it worked much better... I actually almost stripped out a screw using regular phillips head, rather than the JIS one...

breezyjr - Antwort

Great guide, all worked as described. Thanks!

Yes, the screws don't seem to quite match expectations; I used three different #00/#000 drivers before I got a good fit.

Step 7: Could use just a bit more detailed explanation and/or picture. The retainer is on the "back" edge of the connector (facing off the long edge of the trackpad, opposite of Step 6), and takes a mix of delicate firmness to raise. Practice on your replacement (if available).

Step 8: My replacement trackpad came with the trackpad bracket attached, so no need to remove the 6 (orange-circled) screws attaching bracket to trackpad, which can be removed and installed with the bracket attached.

Step 10, reinstalling: Getting the set-screw correctly adjusted was a bit hit-n-miss. My assumption was in far enough to just stop movement, then back off a turn or so. That ended up too loose. YMMV.

Guy Noir - Antwort

I have just finished, there was a scary moment when I managed to somehow cause the retainer clip for keyboard ribbon to fall off the new track pad while I was fitting the cable. I put it together anyway but - of course the keyboard did not work!!! I then took it apart and somehow with the use of an illuminated magnifier, I managed to push the retainer clip back on to the prongs and it works!!

Michael S

Michael Standley - Antwort

Hi,

friend mine did replacement of complete top case with keyboard and trackpad. Seller claimed it is ok but we face one problem. when I touch case (palm rest) trackpad stops responding. Both cases were from A1369 model but on mine was black plastic foil over part of keyboard whiel on other not. So I am not sure there could be some other differences that could cause this.

Would anybody has any suggestion.

Thanks

Frank

frantisek - Antwort

Guide is spot on. I only ran into some difficulty on Step 8. (More details below) Was eventually able to replace trackpad with replacement purchased from here. No more phantom clicks! Although examining the old trackpad and the click "button" makes me wonder if I could have fixed the old one by tweaking the set screw... Regardless, MBA now fully functional again! Wasn't easy but this guide made it not hard to do!

David Lam - Antwort

Very helpfull, thanks.

My maus was driving me crazy. Apple Store wanted to replace the trackpad for 160€ claiming that there was some wetness. I decided to open it myself and clean it with Alcohol(Isopropanol). It was nothing but just dust causing the trigger to behave funny. I bought the 64 Bit Driver Kit from ifixit(64 Bit Driver Kit) . A very proffesional Kit.

NB: Be carefull at stage 8. I spoiled 2 crews here, dont use a lot of energy!!!! If you want to clean the pad then you ONLY remove the RED marked crews.

Henry M. - Antwort

A solution to those suffering from phantom clicks, but otherwise have a working trackpad - there is a solution.

In Step 11 (2nd photo) you can see the little metal cap at the bottom of the trackpad, covered with clear tape. When depressed, this cap should trigger the 'click', but I think with excessive use, I suspect the cap may flatten and make contact with the terminals underneath before you get the 'click' feeling.

I peeled this tape off (with the metal cap) and punched the underside of the metal cap with a screwdriver. This meant that the cap needed a little more force and movement before it made contact with the terminals underneath, and the phantom clicks were no more.

I was probably a bit heavy-handed when I did it, so my trackpad button is quite a bit firmer than before but still quite usable. Be gentle.

Hope this helps someone else - before they spend big on a new trackpad.

Andy Botting - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 16

Letzte 7 Tage: 98

Letzte 30 Tage: 543

Insgesamt: 66,511