Einleitung

This guide will teach you how to remove the Moto Z's rear-facing camera.

  1. Heat an iOpener and apply it to the left edge of the phone for at least 90 seconds.
    • Heat an iOpener and apply it to the left edge of the phone for at least 90 seconds.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

    • As you're waiting for the adhesive to soften, move on and read the following step to get an idea of where to pry.

    Kommentar hinzufügen

  2. In the following steps you will be cutting through the adhesive around the edge of the display assembly.
    • In the following steps you will be cutting through the adhesive around the edge of the display assembly.

    • To avoid damage, do not cut in the following areas:

      • The OLED panel

      • The home button

      • The flash unit

    Kommentar hinzufügen

    • Apply a suction cup as close to the heated edge as possible.

    • Lift on the suction cup and insert the tip of an opening pick into the gap.

    • Do not insert the pick more than 1/16" (1.5 mm). Over-inserting the pick may damage the OLED panel.

    Kommentar hinzufügen

    • Carefully slide the tip of the opening pick down and up the side of the phone, making sure not to cut deeper than 1/16" (1.5 mm).

    • As you run the pick along the side, you will feel the tip of the pick press against the edge of the OLED panel. That is as far as the pick should go without damaging the panel.

    • Once you have separated the adhesive, leave an opening pick in the side to keep the adhesive from resealing.

    Kommentar hinzufügen

    • Repeat the heating, lifting, and cutting steps for the remaining long edge of the phone.

    Kommentar hinzufügen

  3. Kommentar hinzufügen

  4. Kostenloser Versand bei Bestellungen über 20 $
    Verwende den Code BLUEANDBLACK an der Kasse
    Kostenloser Versand bei Bestellungen über 20 $
    Verwende den Code BLUEANDBLACK
    • Insert an opening pick into the flash side corner of the phone and carefully slice around the flash unit.

    • Do not insert the pick more than 1/16" (1.5 mm) into the edge.

    • Once you are done cutting, leave the pick in the corner to prevent the adhesive from resealing.

    Kommentar hinzufügen

    • Insert an opening pick into the remaining top corner of the phone.

    • Carefully slice through the adhesive across the top of the phone.

      • Do not insert the pick beyond 1/2" (12.5 mm).

    Kommentar hinzufügen

    • Apply a heated iOpener to the bottom edge of the phone for at least 90 seconds.

    Kommentar hinzufügen

    • Insert an opening pick into a bottom corner and slice towards the home button, stopping before you reach it.

    • Once you're done with the corner, leave a pick in place to prevent the adhesive from sealing.

    • Repeat the process for the other bottom corner.

    Kommentar hinzufügen

    • Carefully twist the first opening pick slightly to help release the edge adhesive.

    • Repeat the same process for each remaining pick, moving them as necessary and twisting slightly to release the adhesive.

    Kommentar hinzufügen

    • Lift the earpiece end of the display up to provide access to the display cables.

    • Do not open the display beyond 90 degrees, and always support the display panel.

    It says lift home button end of display but the photo shows lifting the earpiece end.

    Lynne Ayers - Antwort

    Good catch! I have fixed the step.

    Arthur Shi -

    • Use the point of a spudger to pry the display cable shield up.

    • Remove the display cable shield.

    Kommentar hinzufügen

    • Use the point of the spudger to lift and disconnect the display cable connector from its socket.

    Kommentar hinzufügen

    • Remove the display assembly.

    • Before you reinstall the display assembly, thoroughly remove any remaining adhesive and glass from the frame.

      • After removing all traces of glue and glass from the frame, clean the adhesion areas with 90% (or higher) isopropyl alcohol and a lint-free cloth or coffee filter.

    • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

    • Use the Motorola Moto Z display adhesive to reseal your phone.

    Kommentar hinzufügen

    • Place the tweezers under the copper tab on the top of the device.

    • Make sure you have a firm grip on the tab with the tweezers.

    • Make sure not to puncture the battery with the metal tweezers as it's a fire hazard.

    Kommentar hinzufügen

    • Slowly and carefully lift up on the tab until it pops out of the phone and is only connected by the black tape.

    Kommentar hinzufügen

    • Using the tweezers, firmly grab the black connecting tape closest to the lens.

    • Gently pull to the right until the camera (lens and black tape) disconnects from the device.

    Kommentar hinzufügen

Abschluss

Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our [|Motorola Moto Z Answers community] for troubleshooting help.

Miriam Lam

Mitglied seit 24.01.2018

876 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team S2-G2, Livingston Winter 2018 Mitglied von Cal Poly, Team S2-G2, Livingston Winter 2018

CPSU-LIVINGSTON-W18S2G2

4 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 3

Letzte 7 Tage: 6

Letzte 30 Tage: 35

Insgesamt: 219