Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

If the drive belt is out of place or jammed, use this guide to replace the drive belt. You will need the T10 and T20 Torx screwdrivers.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Press the two Brush Roll Access buttons down at the same time to detach the cover. Pull the cover off of the vacuum by lifting it up. Pull the cover off of the vacuum by lifting it up.
    • Press the two Brush Roll Access buttons down at the same time to detach the cover.

    • Pull the cover off of the vacuum by lifting it up.

  2. Pull up on the Pull Tab to  remove the large brush roll. Pull up on the Pull Tab to  remove the large brush roll.
    • Pull up on the Pull Tab to remove the large brush roll.

  3. Press the Eject Roller button to detach the small roller. Pull the roller away from the vacuum to remove it.
    • Press the Eject Roller button to detach the small roller.

    • Pull the roller away from the vacuum to remove it.

  4. Use the T20 screwdriver to remove the four 17 mm screws by turning counterclockwise. Use the T20 screwdriver to remove the four 17 mm screws by turning counterclockwise.
    • Use the T20 screwdriver to remove the four 17 mm screws by turning counterclockwise.

  5. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  6. Use the T20 screwdriver to remove the six 19 mm screws by turning counterclockwise. Use the T20 screwdriver to remove the one 12 mm screw by turning counterclockwise.
    • Use the T20 screwdriver to remove the six 19 mm screws by turning counterclockwise.

    • Use the T20 screwdriver to remove the one 12 mm screw by turning counterclockwise.

    • Use the T10 screwdriver to remove the four 14 mm screws by turning counterclockwise.

  7. Use the spudger tool to pry off the red plastic corner cap. Remove the LED headlight casing by pulling up on the casing and out on the corner cap at the same time. Remove the LED headlight casing by pulling up on the casing and out on the corner cap at the same time.
    • Use the spudger tool to pry off the red plastic corner cap.

    • Remove the LED headlight casing by pulling up on the casing and out on the corner cap at the same time.

  8. Remove the red cover by lifting upward.
    • Remove the red cover by lifting upward.

  9. Remove the light fixture by lifting it up.
    • Remove the light fixture by lifting it up.

  10. Use the spudger to detach the orange drive belt compartment from the vacuum. Remove the orange drive belt compartment from the vacuum by lifting it upwards.
    • Use the spudger to detach the orange drive belt compartment from the vacuum.

    • Remove the orange drive belt compartment from the vacuum by lifting it upwards.

  11. Pull outward on the smaller drive belt to remove it.
    • Pull outward on the smaller drive belt to remove it.

    • Pull outward on the larger drive belt to remove it.

    • The smaller drive belt must be removed first in order to remove the second larger belt.

    You need to make a correction…the T20 that you specify to use is incorrect. I just bought a Husky T30, T25, T20, T15 and T10 Torx Screwdriver Set and where you indicate to use a T20, it's actually a T15. Not only is this an issue, another issue is that the screws on this vacuum has a raised dot in the center of it, or however you would call it which creates a problem to even seat the screwdriver in properly to turn. If you have another suggestion or different screwdrivers to use, I'm open to suggestions.

    Lisa R Rowley - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

6 weitere Nutzer haben diese Anleitung absolviert.

Catie Halvorsen

Mitglied seit: 08.10.2018

643 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team S17-G4, White Fall 2018 Mitglied von Cal Poly, Team S17-G4, White Fall 2018

CPSU-WHITE-F18S17G4

4 Mitglieder

6 Anleitungen geschrieben

What a pain in the ***! The star bit wouldn't fit on one of the screws and had to use a small reg. screwdriver to get it out. This is a very poor design. I've only used the sweeper a few times too. Hope the belts don't come off or break often because if they do it's going in the dumpster and never buying another one. Do not recommend this sweeper!!! Very disappointed.

Deann Shumaker - Antwort

The spudger saved the day.

Excellent guide. You saved me hours of frustration

Callum - Antwort

What size belt I need for this vacuum

Melissa Beaver - Antwort

Very bad design will stick to our dyson will not recommend it go any one

satmansteve00 - Antwort

It’s really not bad. This vacuum has out performed and lived many Dysons. I’ll never go back! They are half the price and accept coupons too

ryannmacintosh -

This product is the biggest load of $@$* i have ever bought, stayclear of it

Trevor Hickman - Antwort

Thanks for the help! You did a great job. However, Shark's design for a normally consumer-replaceable part is insane. 1.5 hrs only to find the belts are fine and will have to go to a shop. I will take it in disassembled and save that much on labor. Crazy.

Debbie Thompson - Antwort

I agree with all the negatives above I have a vacuum I bought in May 2018 which does not work as the drive belt doesn’t work, they do not have any service place to attend if like me a full time carer of an 87 year old husband the service on the phone spoke too fast with an American accent I had to ask him to repeat, I found myself taking the vacuum to pieces for analysis whilst on the phone they have nowhere to take it if you cannot go to such lengths.

200.00 a complete waste of money, if you can’t d I y with special tools don’t buy one no satisfaction given whatsoever yes back to dyson at least I can get it serviced

kathleen.cooke - Antwort

Where do I get belts for this. Mine is NV771Q?

Clifford Hendershot - Antwort

Excellent instruction and pictures. It is real pain to take apart, but we paid a lot $ and it works great on our floors.

George White - Antwort

I have the shark apex with duoclean and zeroM the next month the belt broke off, very dissapointed, im switching to dyson.

james langridge - Antwort

Helpful instructions only to find the belts are fine, so now what can it be? The motor???

Lisa R Rowley - Antwort

I love how you try and teach people how to fit their shark duo clean hv380 but you don't let us know where to buy the belts? And no Shark doesn't sell them on their overpriced joke of a website!

Richard Auck - Antwort

A simple google search showed me many places to get belt. One of the first was the shark website. You just have scrolled past.

ryannmacintosh -

Just had to throw mine away. Pure garbage.

rz6x59 - Antwort

This is designed to never be repaired. Once it stops working throw it away.

rz6x59 - Antwort

I fixed mine and I’m a chick. Did you even try ?

ryannmacintosh -

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 36

Letzten 7 Tage: 249

Letzten 30 Tage: 1,167

Insgesamt: 15,338