Einleitung

Steckt deine SIM-Karte im iPhone fest? Folge dieser Anleitung, um den defekten SIM Auswurfhebel eines iPhone 6 zu reparieren oder ersetzen.

Vor der Demontage des iPhones entlade die Batterie auf unter 25%. Eine geladene lithium-Ionen Batterie kann Feuer fangen und/oder explodieren, wenn sie beschädigt wird.
  • Vor der Demontage des iPhones entlade die Batterie auf unter 25%. Eine geladene lithium-Ionen Batterie kann Feuer fangen und/oder explodieren, wenn sie beschädigt wird.

  • Schalte dein iPhone ab, bevor du mit der Demontage beginnst.

  • Entferne die beiden 3,6 mm Pentalobe Schrauben neben dem Lighting Connector.

When reconnecting be VERY careful not to over tighten. The connectors on the screen that these 3.6mm Pentalobe screws lock with are notorious for breaking off

Blair Tryba - Antwort

what do i do if ive managed to tighten them too hard and now they wont come off?

kristian686 -

Before opening the phone, I gently warmed it using a buckwheat heating pad. This made removal of the adhesive strips (steps 20 to 24) easy.

Howard Bales - Antwort

Exactly what I did as well, the gently warming made the adhesive removal work like a charm. The heat as well help to lift the screen easily, no need for the prying tools for me to open te phone.

For the adhesive removal just pull it slowly to the bottom of the phone and keep in under tension.

On reassembly, turn on the phone after getting all connectors back in place to verify all is working fine before putting all screws back in their spot.

Maarten Vergauwen -

I put mine back together but mine looks very different than this one. Why is it that when I make a call I cannot hear through the ear piece and have to put it on speaker. Also my screen doesn't go black when my face touches it

Bailey Wilson - Antwort

Hey Bailey, which repair were you attempting? Is it possible you have a 6s, or maybe a 6 Plus? You may have better luck with faster troubleshooting if you post in our Answer Forum!

Sam Lionheart -

See its a long time ago you had this issue. You can try to remove the cable from front camera/sensor/earpiece from the motherboard port and gently push it back on. All the problems you relate to is thru the same cable. If this dont solve your problem, check if the earpiece is correctly placed onto the polarity poles, and that the proximity sensor is lying right down into the corresponding socket. If something is blocking the sensor, yeah then the screen wont turn on/off when you put it onto your ear.

Kenneth Hilstan -

You only need 000 Screwdriver for ALL!

Tom Long - Antwort

If you skip to STEP 36, you’ll see that you’ll need a STANDOFF SCREWDRIVER BIT to be able to get all the way to Step 39 and remove the antenna. Read through the comments, and you’ll see how frustrated people have gotten since my kit didn’t include the Standoff screwdriver, and I had to dig around for and carefully use a flathead, which took a very long time. If you can’t get that Standoff screw off, you’ll end up with a partially disassembled iPhone and unable to progress. Make sure you have this tool before you proceed.

Brian Mojica -

what do i do if all the screws fail to come off and if i don’t have some of the tools like the iSclack

Brandon Kato - Antwort

I see in the preamble that when you replace your logic board, you would lose touch id functionality, so my question is what if you have the homebutton and thus the fingerprint reader for the logic board replacement, would touch id work?

socratesmens - Antwort

The guide for the iPhone6 battery replacement needs to be revised. There are a couple of issues.

1) While the battery cover has two screws, they are different lengths. Since they are very small, it can be hard to see the difference (until one tries to screw the smaller one into the longer hole). The video needs to mention this.

2) The application of the adhesive strip if very different from what is mentioned. Also, there is a “one piece plastic” applique, and it is very unforgiving. The video should show this process in more detail.

I believe the attention to this detail would help folks correctly install their iPhone 6 batteries, and with the recent Apple disclosed battery problem, would continue to show that iFixit is very committed to the end-user.

Gary Long - Antwort

Please reconsider this repair!

Before you remove any screws, please consider taking your part to a local repair pro and asking them to install it. The many cables connecting the screen assembly to the body of the iPhone are unruly and hard to reconnect. I knicked a cable and thus rendered the entire assembly and repair unfixable. I consider myself capable and tech savvy, but it’s too easy to make a tiny mistake and ruin your phone.

Bruce Coriell - Antwort

I felt a bit silly getting stuck at the end of a long repair, unable to screw one of these last screws back in. What worked was gently pinching the phone above and below the screw, to make sure the screen and back were perfectly aligned.

Matt D - Antwort

Apple edits posts on their Communities website that link to this fix page justifying as follows:

“We’ve edited your post because following the procedures at the site you provided may lead to damage to the user’s device.”

What is certain is that following Apple Support’s advice of resetting our phones again and again never works whereas this fix works. Apparently Apple does not want people to know that their hardware fails and can be fixed, because then they would need to explain why they don’t offer neither the fixing service nor the fixing advice by directing us to this website.

Brice - Antwort

Before you get started, I suggest you confirm you are replacing the correct camera. If you are thinking of a camera, the front is the side of the device with the main lens. On an iPhone this is actually known as the rear facing camera. Once the phone is disassembled your orientation can be distorted and it is not that hard to fail to realize your are replacing the wrong camera. Doh!

William Miller - Antwort

I found it very useful to use a magnet sheet when doing these repairs. I use electrical tape or a sharpie to make a grid, and place each micro screw in a separate box on the grid.

I work directly over the magnet sheet, so that if something drops I have a better chance at not losing it.

If you do lose a screw, go over the work area with a fridge magnet. It will pick it up if it hasn’t popped too far away.

Megan Telliano - Antwort

Die nächsten drei Schritte zeigen die Benutzung des iSclack, ein gutes Werkzeug um das iPhone 6 sicher zu öffnen, welches wir allen empfehlen, die mehr als eine Reparatur durchführen. Wenn du den iSclack nicht benutzt, überspringe die nächsten 3 Schritte und folge einer anderen Methode
  • Die nächsten drei Schritte zeigen die Benutzung des iSclack, ein gutes Werkzeug um das iPhone 6 sicher zu öffnen, welches wir allen empfehlen, die mehr als eine Reparatur durchführen. Wenn du den iSclack nicht benutzt, überspringe die nächsten 3 Schritte und folge einer anderen Methode

  • Wenn der Abstandshalter aus Plastik noch in der Mitte des iSclack ist, entferne diesen jetzt – er ist nicht benötigt für größere Smartphones wie das iPhone 6.

    • Schließe den Griff des iSclack, um die Saugnapf-Zange zu öffnen.

There was only one suction cup in my kit. Why show the need for two if ifixit provides only one?

Lisa Klitses - Antwort

Do Not Worry. The Islack comes seprate. This guide shows you how to remove the front screen with a normal suction cup.

Owen -

I found that the single suction cup from the kit worked very well. It didn’t take that much force to separate the front panel from the phone. I think any suction cup that you are able to get a firm grip on will probably work as well. There isn’t any adhesive holding the front panel in. It just snaps in and out. If you have a cracked screen and no screen protector, it may be hard to get a good suction seal. If that’s the case, someone else here suggested applying clear tape to the front glass to get a good surface for applying the suction cup. In my case, I already had a screen protector that was still intact so the suction cup sealed easily.

fiftysomething - Antwort

  • Platziere das untere Ende deines iPhone zwischen den Saugnäpfen.

    • Positioniere den oberen Saugnapf direkt über (aber nicht auf) dem Home Button und drücke ihn gegen das Display.

  • Öffne den Griff um die Zange zu schließen. Platziere die Saugnäpfe mittig und drücke Sie kräftig gegen die Ober- und Unterseite des iPhones.

Kommentar hinzufügen

  • Halte dein iPhone gut fest und schließe den Griff des iSclack, um die Zange zu öffnen. Die Saugnäpfe heben dabei die Display Einheit von der Rückseite des Gerätes.

  • Das iSclack Öffnungswerkzeug wurde entwickelt, um dein iPhone genau so weit zu öffnen, dass die Teile getrennt werden können, aber keine Kabel beschädigt werden.

  • Löse die Saugnäpfe von deinem iPhone.

  • Überspringe die nächsten drei Schritte und fahre fort mit Schritt 8.

The iSclack opened the iPhone 6 with little effort. I could have given even less opening pressure than I did. Fantastic tool. Worth the investment.

Tim Dougherty - Antwort

It's never mentioned anywhere that with iSclack even if you save the cables, glass easily detach from plastic frame. When you ri-assembly the phone, this will involve a glass not perfectly adherent to the body. In my opinion is better if you help yourself with a spudger to lift frame from rear case when you are using the iSclack.

marco bigoni - Antwort

Holy cow this tool made it so much easier than a spudger and didn't damage anything. Totally worth the investment.

Fratelli '85 - Antwort

Really need to get one of these. so much easier then the basic type.

Richard W - Antwort

  • Stecke ein SIM-Karten Eject Werkzeug oder eine Büroklammer in das kleine Loch des SIM-Karten Einsatzes.

  • Drücke, um den Einsatz auszuwerfen.

  • Dies benötigt vielleicht mehr Kraft als gedacht.

Why isn’t this the first step in the process? Seems unnecessarily risky to fumble with popping the SIM in and out when you’ve already opened up the phone.

Perrin Haley - Antwort

If you don’t have something small enough to open it, you can use the lever when the screen is off.

Lucas Rowlands -

  • Entferne den SIM-Karten Einsatz aus dem iPhone.

  • Achte beim wieder einsetzen darauf, dass die SIM-Karte in der korrekten Ausrichtung im Einsatz steckt.

Kommentar hinzufügen

  • Entferne die einzelne 1,7 mm Kreuzschlitz #00 Schraube, die den SIM Auswurfhebel befestigt.

Remova o parafuso Phillips # 00 de 1,7 mm que fixa a alavanca de ejeção do SIM.

Maximiliano Fischer - Antwort

  • Entferne den SIM Auswurfhebel aus dem iPhone.

  • Merke dir die Ausrichtung für den Wiederzusammenbau: Das breitere Ende sollte auf Höhe des Loches für den SIM-Karten Auswurf sein.

Kommentar hinzufügen

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

35 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Jasper Fleischhauer hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Sam Lionheart

Mitglied seit 18.10.2012

327.653 Reputation

1.681 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

109 Mitglieder

6.224 Anleitungen geschrieben

Bonjour, mon tiroir ne sort pas sauf quand j’appuie sur le téléphone pour le compresser, il manquerait une rondelle ou autre épaisseur ? merci

Farid Le Déglingo - Antwort

Where can we purchase the eject lever though?

Crav - Antwort

So i recently did a rear housing replacement and forgot to but the eject lever in before putting in my sim card is there any way to fix this

if so email Nanakyeretwie46@gmail.com

Nana Kyeretwie - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 10

Letzte 7 Tage: 65

Letzte 30 Tage: 339

Insgesamt: 31,166