Repariere deine Sachen Community Store

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Geschrieben von: Andrew Optimus Goldheart (und 5 anderen Mitwirkenden)
  • Kommentare: 9
  • Favoriten: 1
  • Vollendete Reparaturen: 1

Schwierigkeitsgrad

Mittel

Schritte

7

Zeitaufwand

Eine Zeit vorschlagen??

Abschnitte

1

  • 7 Schritte

Kennzeichnungen

1

Prerequisite Only

Grundständige Anleitung

Bitte beachte, dass diese Anleitung nur eine grundständige Anleitung für andere Anleitungen ist.

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Remove three 1.6 mm #000 Phillips screws securing the logic board to the rear case.

    • Remove three 1.6 mm #000 Phillips screws securing the logic board to the rear case.

    Übersetzen

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    There are two strips of adhesive keeping the battery in place.

    • There are two strips of adhesive keeping the battery in place.

    • Turn the iPod over and heat the BACK of the aluminium iPod case. Do not heat the battery.

    • The aluminium case does not have to be hot; you should always be able to touch heated parts with your fingers at all times without it being uncomfortable.

    Übersetzen

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    There are three notches on either side of the battery. In the next few steps, you will be using these notches to gradually pry the battery up from the rear case. The battery is secured with large amounts of adhesive, so you'll need to go slowly and carefully to avoid puncturing or creasing the battery.

    • There are three notches on either side of the battery. In the next few steps, you will be using these notches to gradually pry the battery up from the rear case.

    • The battery is secured with large amounts of adhesive, so you'll need to go slowly and carefully to avoid puncturing or creasing the battery.

    • Insert a plastic opening tool into the top right notch and gently pry up on the battery.

    • Do not attempt to pry up the entire battery at this point; you just want to start to loosen the adhesive at each of the prying points, in turn.

    Übersetzen

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Continue with the lower right notch. Insert the plastic opening tool into the notch, and gently pry up on the side of the battery. Continue with the lower right notch. Insert the plastic opening tool into the notch, and gently pry up on the side of the battery.

    • Continue with the lower right notch. Insert the plastic opening tool into the notch, and gently pry up on the side of the battery.

    Übersetzen

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Continue prying the battery up from the bottom. When prying along the bottom, be careful not to press down too hard against the speaker or headphone jack.

    • Continue prying the battery up from the bottom.

    • When prying along the bottom, be careful not to press down too hard against the speaker or headphone jack.

    Übersetzen

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Pry along the left side as well. You may need to move back and forth between the sides and bottom of the battery, prying a small amount at a time until the battery is entirely free from the adhesive.

    • Pry along the left side as well.

    • You may need to move back and forth between the sides and bottom of the battery, prying a small amount at a time until the battery is entirely free from the adhesive.

    Übersetzen

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Once all of the adhesive is loosened, lift the battery up from the bottom and swing it out over the left side of the rear case. Be sure not to yank it out, as it is soldered to the logic board. Flip the battery over to straighten its cable and set it down.

    • Once all of the adhesive is loosened, lift the battery up from the bottom and swing it out over the left side of the rear case.

    • Be sure not to yank it out, as it is soldered to the logic board.

    • Flip the battery over to straighten its cable and set it down.

    Übersetzen
Ziellinie

Ein weiterer Nutzer hat diese Anleitung absolviert.

Tinte & Feder

mit 5 anderen Mitwirkenden

Andrew Optimus Goldheart

Mitglied seit: 17.10.2009

483.879 Reputation

410 Anleitungen geschrieben

Auszeichnungen: 44

+ 41 mehr Auszeichnungen

Team

iFixit Mitglied von iFixit

Community

146 Mitglieder

17.275 Anleitungen geschrieben

3 Kommentare

You skipped steps.

Nick - Antwort

This isn't even half of the procedure - the battery isn't even completely removed, much less replaced! Helpful but nowhere near complete.

Paul Pearah - Antwort

Yeah, you might have skipped the most critical steps, like glass and bezel removal, desoldering, soldering etc..

dominic benavente - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 0

Letzten 7 Tage: 1

Letzten 30 Tage: 4

Insgesamt: 2,623