Repariere deine Sachen Community Store

Das 15" MacBook Pro, Modell A1989, kam im Juli 2018 auf den Markt. Es ist ausgestattet mit einem 15,4" LED hintergrundbeleuchtetem Display mit True Tone Technologie, TouchID und bis zu einem 6 Core i9 Prozessor.

203 Fragen Alle anzeigen

Einstellungen

Ripped battery connector from logic board

Hey there,

Unfortunately, I ripped the tiny battery connector from the logic board, while trying to take out the battery (picture attached). Is there any way to repair that or do I need to replace the logic board?

Block Image

Update (06/19/23)

Here’s another picture attached. The object (plug?) in the green circle would needed to be placed where the red arrow is pointing to. While trying to take off the cable i ripped it of the logic board.

Block Image

Diese Frage beantworten Ich habe das gleiche Problem

Ist dies eine gute Frage?

Ja Nein
Bewertung 1
Einen Kommentar hinzufügen

4 Antworten

Filtern nach:
Am hilfreichsten Neueste Älteste
Hilfreichste Antwort

Einstellungen

Looks like one solder pad is already missing, thats means you must find in schematic where this line is going and can route a patch line to reconnect it.

When you share the exact motherboard number i can look to schematics.

And good repair shops? Yes, in Wien you can visit me 😄

War diese Antwort hilfreich?

Ja Nein
Bewertung 3

5 Kommentare:

Or only model number A**** will be enought to find the line.

von

@vojtech59738 maybe with a closer, clearer picture the trace for the pad may be visible.

von

It's an A1990 model. I will add another picture

von

@nigel yes when is on the 1st Layer, but this MacBook have 7layers PCB.

von

@vojtech59738 on the second picture you can see the trace going to the ripped pad. Doesn’t look like a hard job to fit it. Looking at it you could probably expose part of the trace and run solder from the connector pin to the trace. I did it once with a vape circuit board. Trace was that close to the pin there was no point running a wire.

von

Einen Kommentar hinzufügen

Einstellungen

it can be repaired but it would need someone with good soldering experience to repair it

War diese Antwort hilfreich?

Ja Nein
Bewertung 2

27 Kommentare:

Hey @tech_ni & @strongbow,

could you recommend any Repair-Service in Europe/Germany? And, is there any tutorial for the soldering? We have some guys in the company who said they would dare to try by themselves ;)

von

@fen18106 looking at the great bunch of people (excluding myself) that answered you question, I think you already have all the right experts to help you with that repair

von

@fen18106 if your in germany ben or some of the techs at resq would be able to repair it. https://www.resq-repair.com/en. if any of them pads are damaged then you would need the boardview to see where they go and run jumper wires

von

@tech_ni solder a jumper to R6952 :-) boardview verified :-))

von

@oldturkey03 820-00850 board im guessing

von

22 weitere Kommentare anzeigen

Einen Kommentar hinzufügen

Einstellungen

@fen18106 let us know what board number you have on there. I show a 820-01041. That particular pad is SMBUS_3V3_BATT_SCL and could connect directly to R6952.

@strongbow the trace is visible but a PITA top solder too, I'd solder a jumper to the component :-)

Block Image

I am really not sure if the pad is actually off or just needs to be cleaned. Must be my old eyes :-)

War diese Antwort hilfreich?

Ja Nein
Bewertung 2

3 Kommentare:

Re-tinning the pads would be a good start then check the path using an Ohm meter or continuity tester between.

Just be careful as you could make things worse.

von

The pad is definitely off - i had it right in my hands ;)

The board number is 820-01041 or 820-01326 - on the box of the MBP "Radeon Pro 560X" is written - and on logi.wiki there is "Radeon ... vega", so I am not 100% sure which one it is: https://logi.wiki/index.php/Board_Number...

von

@fen18106 like I said, maybe my old eyes. Always good to verify. So, the instructions are right and it's the right component to run a jumper to.

von

Einen Kommentar hinzufügen

Einstellungen

Decent computer repair shop should be able to repair that for you. With the correct connector should be easy enough.

War diese Antwort hilfreich?

Ja Nein
Bewertung 1
Einen Kommentar hinzufügen

Antwort hinzufügen

FeN. wird auf ewig dankbar sein.
Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 19

Insgesamt: 282