Diese Person hat ihr Profil noch nicht ausgefüllt.
Absolvierte Anleitungen
Seite 1 von 5
Fragen
Customer brought in his daughter's iPhone XR for a screen change. I tested all functions before beginning without any...
Mehr erfahrenHi. I received the above iPad from a customer who was just looking to get it off her hands. It’s in good condition and all...
Mehr erfahrenReplaced the logic board and the charge port in an iPhone 6S Plus. Now, I have no earpiece speaker or loudspeaker sound,...
Mehr erfahrenI have an LTE 5th generation tablet with a damaged logic board. I was wondering, since these two tablets are essentially...
Mehr erfahrenWithin the last few days, I’ve changed the digitizer on two different iPad 4’s. I changed it 4 different times and each...
Mehr erfahrenI have replaced the screens on many iPhone 8 Plus phones, but its only recently that I’ve been having trouble. Every...
Mehr erfahrenRepairing a galaxy note 4 and cannot get the phone to work at all. I’ve changed the battery, the screen, and the...
Mehr erfahrenHi. Looking for some assistance. I changed the digitizer and power button cable on an iPad 3. Touch was not working, so I...
Mehr erfahrenForum
Hi Tanner. Check to make sure that the daughterboard is the right one for your carrier or location. Looking at one of the vendors that I get my parts from, there are two different daughterboards for this model phone. One is a North American version, and the other is an international version. You may have gotten the wrong one. I'm not 100% sure about this model, but I have also seen some models that have different daughterboards for different carriers. So, if you're with AT&T and you're using a daughterboard that is only designed to work with Verizon models, you may encounter this issue. Hope that helps!
Mehr erfahrenHi Marty. Changing the NFC charging coil is sometimes the answer to that issue, but I've noted that just making sure the screws that hold the coil in place are tight helps. I'm not 100% sure about the Note 10+, but for most of the Galaxy models I've worked on, the temperature sensor is affected by contact points on the motherboard making connection with points on the back of the coil component. Being that on this model the NFC coil actually snaps into the motherboard, could make for a big difference in how this one operates. If that's the case, you most likely have a defect in the motherboard. Sorry I'm not much help, but try checking with some of the phone repair locations in your area. If any of them specialize in motherboard or logic board repair, they might be able to give you an idea if there is board damage. Hope you get it figured out.
Mehr erfahrenThis piece is mostly just a bracket to help hold things in place, but it does have contact points on it. So, if you've broken any of those contact points or it is just bent completely out of shape, you can easily replace it. https://www.mobilesentrix.com/full-set-small-metal-bracket-for-iphone-11 Also, it doesn't hurt to see how the phone works without it. These brackets are useful in most cases, but sometimes they seem almost as if they are just for show.
Mehr erfahrenLooks like damage to the LCD. You’ll probably have to replace it. iPad 6 tablets have a small amount of adhesive which holds the corners down where the screws are inserted. If you applied too much pressure beneath the LCD to pull it up, it could have damaged it.
Mehr erfahrenNothing works. I plugged it in to test it and nothing.
Mehr erfahrenLooks like your LCD is damaged. Can happen any number of ways? Bring it to a reputable repair shop to have the screen changed and see if that fixes the problem.
Mehr erfahrenPotentially a bad replacement screen. As well, the battery will sometimes drain completely down if you didn’t power down the phone or disconnect the battery prior to either disassembling the phone or disconnecting the screen. Try to charge the battery if you haven’t already. Hope that’s helpful.
Mehr erfahrenMy first thought is you fried your charge port somehow, but if you have connected to iTunes and can actually attempt to charge your battery, then your charge port is fine. An unfortunate side effect of changing the screen is that sometimes it can affect your battery. Did you power down your phone before beginning the repair, and did you unplug the battery before disassembling the phone? If you didn’t, this can sometimes have a negative affect on the battery. I’ve seen them run completely down, to where the battery has to be completely recharged after a screen change and I’ve also seen where they just don’t have the same life they used to have after a screen change. You might attempt to have your battery changed. If you encounter the same problem, the issue could lie with the logic board. Hope that’s helpful.
Mehr erfahrenAnleitungs-Kommentare
I had a similar issue as Dave. What worked for me was attaching it to the component before installing the whole charging port into the phone’s frame.
Why is the removal of the proximity light sensor from the back of the screen not covered in this tutorial?
I was able to fix this issue for a customer and all I did was clean the charge port free of lint. This may not work in every situation, but its definitely worth a try if you’re trying to avoid buying a new phone.
I was able to do this the first time w/out damaging the LCD simply by following the instructions to the letter, slowly and carefully. The only thing I did differently was to follow Northstar’s instructions to remove the two pieces of tape at the bottom of the LCD before beginning.
Why is the power button not included in this guide? It’s part of the repair.
Jenny Lawson
@jennyslaw
277
Reputation
8
Lösungen
0
Anleitungen
Mitglied seit 08/08/18
Team
The Device Dr.
We repair and diagnose your smartphones and tablets.
Stimmen
6
0