Diese Person hat ihr Profil noch nicht ausgefüllt.
Anleitungen, zu denen ich beigetragen habe
Fragen
Hi iFixit! I repaired an iPhone 8+ screen for my customer , after repair the home button no longer works however it does...
Mehr erfahrenHi All, Got a Surface Pro 4 - Stopped booting, would not detect internal SSD from any Live USB / Recovery / Windows...
Mehr erfahrenOk, got a friends 13” Late 2013 Retina 13” MacBook Pro. Came to me with no power / wouldn’t start. It would show the “low...
Mehr erfahrenHi All, Had an iPhone 5 come in with broken LCD and non-functioning home button. Replaced the LCD without an issue however...
Mehr erfahrenHi all Found a 32GB 5th gen on eBay. Listed as working except for screen issues and cracked digitiser. After some...
Mehr erfahrenHi All I am in the process of repairing a customers Surface Pro 4 LCD. During the removal of the broken LCD I accidentally...
Mehr erfahrenHi All I live in Australia so I cannot purchase the iFixit adhesive remover :-( Anyone got any tips for making battery...
Mehr erfahrenHi Everyone Never had this one before. Replaced a LCD on a customers iPhone 6S yesterday and they sent me the following...
Mehr erfahrenHi All, Just replaced a digitizer on an iPad 5 (2017 model). All went fine, was very careful. Home Button assembly hasn't...
Mehr erfahrenHi All, Just wondering as per title is The G920R7 (LTE-A) Frame & LCD Compatible With G920F Motherboard? Watching a cheap...
Mehr erfahrenSeite 1 von 2
Forum
It's possible the replacement hard drive cable could be bad - I remember I ordered 5 of them once and 2 of them were dead on arrival. Either that , or the hard drive itself requires replacement. The flashing folder happens when the MacBook can't detect the operating system. If you have installed a new ribbon cable but the hard drive has failed, or a new hard drive but have not reinstalled the operating system, you'll see the flashing folder. Easiest way to check would be to boot into either Recovery mode or off an install USB if you have one and load up Disk Utility. If the hard drive appears and you can run First Aid on it and it passes, the drive should be fine. If the hard drive doesn't appear when connected to the ribbon cable but does appear when connected externally, your ribbon cable is probably bad.
Mehr erfahrenI would firstly check that both ends of the LCD ribbon cable are properly secured, then secondly would try replacing the LCD ribbon cable. If still no good, replace the LCD panel.
Mehr erfahrenDouble check all the screen connections carefully. If they are properly connected and you still don't have any touch functionality, send the screen back to where you bought it from and get it exchanged for another. If the replacement screen does the same thing, it could be a defect with the actual connection on the logic board which the screen connects to.
Mehr erfahrenFrom comparing the technical specs I would say no this isn't possible. The 2010 has a Mini DisplayPort while the 2012 has a Thunderbolt port instead - this difference in ports would mean that the holes in the housing would not line up with the other logic board so it wouldn't fit.
Mehr erfahrenHi Mason You can find a replacement screen here: https://www.etradesupply.com/oem-htc-evo-4g-lte-lcd-screen-and-digitizer-assembly-with-light-guide-black.html If you are attempting the repair yourself, there is a YouTube video here which you can follow: https://www.youtube.com/watch?v=Nc43lhXZ...
Mehr erfahrenIf the phone isn't charging it could either be a fault with the charger, the USB lightning cable, the battery or the charging port in the phone (or a combination of some or all of those parts) The charger and cable you can easily replace yourself, so I would start there! borrow one from a friend if you don't have a spare. If that doesn't fix the problem, then look at replacing the battery and charging port in the phone.
Mehr erfahrenHi John Which model of smartwatch did you have? Alex
Mehr erfahrenHi I had exactly the same problem recently with a Mid 2012 13" Macbook Pro and tried all the steps you mentioned. Turned out that I had a broken battery sensor (flat connector on the bottom right hand side of the logic board which is connected to the button on the right hand side that shows battery power level) After disconnecting this connector and doing (yet another) PRAM and SMC reset, the Macbook started working. Will be ordering another battery indicator cable but for now leaving it unplugged. Charging light went orange and it detected and charged the battery right up to 100% and has been sitting running on battery power for hours now with the battery indicator cable disconnected! Also another thing to make sure is that you have the latest SMC Update installed , as SMC version 1.5 did resolve battery issues. (And SMC v1.8 on the 2012 model) https://support.apple.com/kb/DL1474?loca...
Mehr erfahrenHi Seeing as you have changed the hard drive cable already, the first thing I would say is try another hard drive or SSD that you know is brand new. If the customer has supplied the drive you don't know how old it is or whether it has errors etc. I have also encountered a lot of issues in the past with OCZ SSD's in older Macbooks. I use Samsung EVO or Sandisk Ultra II SSD's without an issue - Get either of these brand new, load the OS onto it and see if that stops the issue
Mehr erfahrenJust to add my two cents ... I have managed to fit a logic board from a Mid 2012 13" Macbook Pro into the casing of a Late 2011 13" Macbook Pro without any problem. Not sure if the same would apply for the 15" though
Mehr erfahrenSeite 1 von 3
Alex S
@aberfoyleparkpc
588
Reputation
28
Lösungen
0
Anleitungen
Mitglied seit 09/05/13
Team
Aberfoyle Park PC Repairs
Affordable PC, Mac, Phone & Tablet Repairs in Adelaide,...
Stimmen
20
1