Zum Hauptinhalt wechseln

iPhone 14 후면 유리 교체

Englisch
Koreanisch

Grundständige Anleitungen

Bevor diese Anleitung als vollständig übersetzt gilt, müssen alle grundständigen Anleitungen übersetzt werden.

iPhone 14 Pentalobe/펜타로브/별나사 교체

여는 픽을 3mm에 표시하기

Informationen zur Anleitung

= Fertig = Unvollständig
    Use this guide to replace a broken rear glass on your iPhone 14. The rear glass includes the charging coil and rear-facing microphone mounted on it.
    This guide was created using the ***A2882*** (international) model. If you're fixing a different iPhone 14 model, there may be some visual discrepancies, but the procedure should be the same.
    ***For your safety, discharge the battery below 25% before disassembling your device.*** This reduces the risk of fire if the battery is accidentally damaged during the repair. If your battery is swollen, [[What to do with a swollen battery|take appropriate precautions|new_window=true]].
    ***Note***: On iOS 18 and newer, you can pair new, genuine rear glass parts using Apple's [link|https://support.apple.com/en-us/120579|Repair Assistant|new_window=true].
    You’ll need replacement adhesive to reattach the screen when reassembling the device. Your device will function normally, but will most likely lose its IP (Ingress Protection) rating.
      Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
      ***To reassemble your device, follow the above steps in reverse order.***
      After your repair, depending on the replacement part, you may be able to [link|https://support.apple.com/en-us/120579|calibrate it using Apple's Repair Assistant|new_window=true], available as of iOS 18. Update your device, navigate to Settings ***→*** General ***→***About ***→*** Parts & Service History, tap Restart & Finish Repair, and follow the onscreen prompts.
      Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
      Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or ask our [link|https://www.ifixit.com/Answers/Device/iPhone%2014|Answers community] for troubleshooting help.

      Anleitungsschritte

      1. Schritt — 깨진 부위에 테이프 붙이기

      iPhone 후면 유리가 깨졌다면, 수리하는 동안 유리에 테이프를 붙여서 추가 파손을 막고 신체적 상해를 방지하세요.

      2. Schritt — 안티클램프 사용법

      다음 세 단계는 여는 절차를 더 쉽게 하기 위해 고안된 도구 안티-클램프에 대한 설명입니다. 안티클램프를 사용하지 않는다면 세 단계를 건너뛰고 대안을 사용하세요.

      3. Schritt

      파란색 손잡이를 앞으로 당겨 팔을 잠그세요.

      4. Schritt

      두꺼운 표지 책과 같은 튼튼한 물체로 iPhone을 받쳐서 손으로 잡을 필요가 없는 상태로 바닥과 평행하게 놓으면 다음 단계에서 작업하기가 더 쉬워집니다.

      5. Schritt — 하단 가장자리 가열하기

      흡입 핸들을 사용한다면 다음 두 단계를 따라서 후면 유리를 풀어주세요.

      6. Schritt — 여는 픽 끼우기

      흡입 핸들을 후면 유리 하단 가장자리에 유리 가장자리는 피하면서 부착하세요.

      7. Schritt — 왼쪽 가장자리를 가열하기

      헤어드라이기를 사용하여 iPhone의 왼쪽 가장자리를 90초 동안 또는 후면 유리가 약간 뜨거워져서 만질 수 없을 때까지 가열하세요.

      8. Schritt — 왼편 가장자리 접착제 자르기

      여는 픽을 iPhone 왼편 하단 모서리를 돌아 왼편 가장자리 위로 밀어서 후면 유리를 제자리에 고정하는 접착제를 자르세요.

      9. Schritt — 화면 정보

      iPhone의 오른쪽 가장자리를 따라 연약한 케이블이 있습니다. 케이블이 손상될 수 있으므로, 여기에 픽을 끼우지 마세요.

      10. Schritt — 오른쪽 가장자리를 가열하세요

      헤어 드라이어를 사용하여 iPhone의 오른쪽 가장자리(전원 버튼이 있는 가장자리)를 90초 동안 또는 후면 유리가 약간 뜨거워져서 만질 수 없을 때까지 가열하세요.

      11. Schritt — 오른편 가장자리 접착제 자르기

      픽을 iPhone 하단 가장자리에 다시 끼우고 오른편 가장자리를 따라 위로 밀어서 계속 접착제를 자르세요.

      12. Schritt — 상단 가장자리 가열하기

      헤어 드라이어를 사용하여 iPhone의 상단 가장자리를 90초 동안 또는 후면 유리가 약간 너무 뜨거워져서 만질 수 없을 때까지 가열하세요.

      13. Schritt — 상단 가장자리 접착제 자르기

      휴대폰 오른편 상단 가장자리 밑에 픽을 끼우세요. 픽을 오른편 상단 모서리를 돌아서 상단 가장자리를 반쯤 가로질러 미세요.

      14. Schritt

      휴대폰 왼편 상단 가장자리 밑에 픽을 끼우세요. 픽을 왼편 상단 모서리를 돌아서 상단 가장자리를 반쯤 가로질러 미세요.

      15. Schritt — iPhone 열기

      후면 유리에서 흡입 핸들을 분리하세요..

      16. Schritt — 배터리 커넥터 커버 나사 풀기

      Y000 스크루드라이버를 사용하여 배터리 커넥터 커버를 고정하고 있는 1.3mm-길이 나사 두 개를 풀어주세요.

      17. Schritt — 배터리 커넥터 커버 분리하기

      핀셋으로 배터리 커넥터 커버를 잡고 위쪽으로 밀어(A15 프린트를 향해) 상단 고리를 풀어주세요.

      18. Schritt — 배터리 분리하기

      Spudger/스퍼저 또는 깨끗한 손톱을 사용하여 배터리 커넥터를 로직 보드의 커넥터 소켓에서 들어올려 분리하세요.

      19. Schritt — 충전 코일 커넥터 커버 나사 풀기

      Y000 스크루드라이버를 사용하여 충전 코일 커넥터 커버를 고정하는 1.0mm-길이 나사를 풀어주세요.

      20. Schritt — 충전 코일 커넥터 브래킷 분리하기

      핀셋을 사용하여 충전 코일 커넥터 커버를 분리하세요.

      21. Schritt — 충전 코일 분리하기

      Spudger/스퍼저의 뾰족한 끝을 사용하여 커넥터를 소켓에서 똑바로 들어 올려서 충전 코일 케이블을 분리하세요.

      22. Schritt — 후면 유리 어셈블리 분리하기

      후면 유리 어셈블리를 분리하세요.

      Deine Beiträge sind lizenziert unter der Open-Source Creative Commons Lizenz.