Zum Hauptinhalt wechseln

Einleitung

如果你的PS4运行起来很吃力,或者经常过热导致提示你更换风扇,参考本指南来解决它。请注意任何自行更换配件和拆解都会使索尼的质保失效。

卸下主板需要分离处理器及散热片之间原厂的散热胶。在你重新组装你的设备时,需要重装一层新的散热胶。参考本指南以了解更多。

  1. 将PS4翻转使底面朝上。
    • 将PS4翻转使底面朝上。

  2. 撕除PS4后部的四个封帖。 移除任何一个封帖将会使你失去索尼的质保。
    • 撕除PS4后部的四个封帖。

    • 移除任何一个封帖将会使你失去索尼的质保。

  3. 卸下4颗PS4后部的9mm TR9 内凸梅花螺丝。
    • 卸下4颗PS4后部的9mm TR9 内凸梅花螺丝。

    Depending on the model of PS4, (i.e. CHU-1001A vs. CHU-1215A) it may only have the two screws in the center, not the edge ones.

    Sawyer Coe - Antwort

  4. 保持设备底部朝上,向上抬起设备后侧以卸下底部外壳。
    • 保持设备底部朝上,向上抬起设备后侧以卸下底部外壳。

  5. 卸下3颗固定电源供应组件的9mm TR9 内凸梅花螺丝。
    • 卸下3颗固定电源供应组件的9mm TR9 内凸梅花螺丝。

    • 卸下2颗4mm Phillips #1螺丝。

    It looks like that for CUH 1216A model, security TR8 and PH0 fits better

    . . - Antwort

  6. 从电源供应上拔下电源供应的连接器。 抬起电源供应单元以将其从盒子上卸下。
    • 从电源供应上拔下电源供应的连接器。

    • 抬起电源供应单元以将其从盒子上卸下。

    you need to lift the power board/box up vertically first as there are 2 long prongs extending up into the box. if you try to lift just one end you will bend the prongs.

    pollytintop - Antwort

    has anyone used any of these guys, i don't fancy doing it

    http://www.trustedrepairs.co.uk/electron...

    Damian - Antwort

    during this step it exposes a black phillips head screw at least on some models(such as mine) this screw mates the metal sandwich around the motherboard together. I was unable to perform step 19 until I released this Black short Phillips screw.

    gfinch1 - Antwort

    I just came across this screw at the same time. It is extremely stuck and I'm afraid to strip it. Any ideas?

    Richard Maya -

    The picture shows the power supply connector being removed from the main board instead of the power supply. This conflicts with the instructions which are correct given how it was most likely put together.

    Clay W - Antwort

    This is a poor instruction. Obviously you need to lift the psu out first but on my white ps4 it simply won't budge on one side. Now I'm stuck already.

    Rainer De Temple - Antwort

    Rainer, look at pollytintop’c comment. Lift vertically and you will get to next step. I used a screwdriver on the side opposite the fan, but I am a savage in many ways. If you insist on treating it delicately a small suction or powerful tape might work.

    We may not all make it back. Good luck

    Mello - Antwort

    Guten Tag,

    an dem Mainboard meiner PS4 ist die Buchse mit den Metallstücken drin, wo man den Stecker des Netzteils reinsteckt, abgebrochen. Als ich das Netzteil rausnehmen wollte, habe ich viel zu fest gezogen und nun ist es ab.

    Bilder: https://imgur.com/a/hIMeWTh

    Welche Methoden gäbe es dieses Problem zu beheben?

    Mit freundlichen Grüßen

    JotEssYT - Antwort

    It feels very stuck, but if you can just get the “more" stuck end up a little first (I gently used a screwdriver as a skinny finger) and hold it there with your real fingers, you can get the easier side up a little too, then lift both together simultaneously with your hands. (1001a model, here)

    Linus Porter - Antwort

    Tip is to turn it upside down n gently wiggle the weight of it will bring it out

    Chicky Boy3 - Antwort

  7. 向下按压金属释放条,并小心地拉出扁平线缆以从光驱上断开扁平线缆的连接。这不需要用很大力。 从主板上断开线缆另一端;请确认向下按压了金属释放条,并小心地拉出扁平线缆。
    • 向下按压金属释放条,并小心地拉出扁平线缆以从光驱上断开扁平线缆的连接。这不需要用很大力。

    • 从主板上断开线缆另一端;请确认向下按压了金属释放条,并小心地拉出扁平线缆。

    If your PS4 eject button doesn’t respond/work and it doesn’t accept discs ( it doesn’t beep or nothing happens when you touch the eject button and it doesn’t make noise when you try to put a disc in and doesn’t take it) it could be because you took the wire ribbon out the optical drive or motherboard the wrong way and did not press down on the metal tab. ( like I did ) the wire ribbon should have these tiny “wings” on both sides and on both ends. Easy and very cheap fix. Ordered a new ribbon wire on amazon for $12!!! Better then buying a new PS4!!!!

    manny730 - Antwort

    Any way to get one of those wings out ? One of them broke off as I was pulling the cable out and is stuck.

    Luke Griffiths -

    Attention, pour sortir la nappe de connection du lecteur optique, il faut appuyer sur la lame métallique du connecteur avant de tirer sur la nappe, c’est un verrou.

    LOPAT - Antwort

    Just to emphasize, these are called ZIF cables, or “zero insertion force".

    Truly, you only need to press on the metal button and pull gently *straight* out. No wiggling. No yanking. There is no click.

    If you're putting it back in, the clip “clicks" into place by popping back up.

    Linus Porter - Antwort

  8. 从主板上拔下光驱线。
    • 从主板上拔下光驱线。

  9. 从主板上拔下WIFI线。
    • 从主板上拔下WIFI线。

  10. 卸下4颗9mm TR9 内凸梅花螺丝。
    • 卸下4颗9mm TR9 内凸梅花螺丝。

    • 卸下5mm Phillips #1螺丝。

    Mine on the bottom right near the board was a 5mm Phillips #1 instead of the expected 9mm Torx screw. Also, I have a shield plate covering my (or my customer's) board here.

    CPR Matthews, NC - Antwort

    Mine is the same

    Jesse King - Antwort

    Model Cuh1001a

    Jesse King - Antwort

  11. 卸下WIFI天线。
    • 卸下WIFI天线。

  12. 向上抬起并卸下光驱。
    • 向上抬起并卸下光驱。

  13. 将设备翻转并卸下左侧顶盖。(按压向外推然后向上抬即可将其卸下。)
    • 将设备翻转并卸下左侧顶盖。(按压向外推然后向上抬即可将其卸下。)

  14. 卸下两颗9mm TR9内凸梅花螺丝。
    • 卸下两颗9mm TR9内凸梅花螺丝。

    • 卸下5mm Phillips #1螺丝。

  15. 抽出并卸下硬盘盒。
    • 抽出并卸下硬盘盒。

  16. 向上抬起顶盖的前部并向向后滑动。
    • 向上抬起顶盖的前部并向向后滑动。

    my right corner, by the ps4 logo, was VERY snug, it took me a few minutes to pop that corner off, took a decent amount of force to pop it off

    theyoonion - Antwort

    we used the screwdriver to pry it open in the corner

    Sabrina Shahid - Antwort

    I try being extremely gentle when working with electronics, but you need a tad more force this. Perhaps you'll need the same force for pulling those miles cables for the optical drive earlier. :)

    Linus Porter - Antwort

  17. 卸下12颗9mm TR9内凸梅花螺丝。
    • 卸下12颗9mm TR9内凸梅花螺丝。

    There’s a black Phillips screw next to the power supply connector that needs removed before removing the metal cover.

    louhobby - Antwort

  18. 卸下2颗9mm Phillips head #1 螺丝。 卸下金属支架。
    • 卸下2颗9mm Phillips head #1 螺丝。

    • 卸下金属支架。

    Danach muss auf der Innenseite noch eine schwarze Schraube gelöst werden, sonst kann man die Abdeckung und auch nicht Mainboard lösen.

    Maik Heidemann - Antwort

  19. 向上抬起并卸下金属屏蔽盖。
    • 向上抬起并卸下金属屏蔽盖。

    On some PS4 consoles there is a small black Phillips head screw under the PSU securing the metal cover to the midframe of the console. If you do not remove this screw you will not be able to remove the metal cover, and run the risk of damaging it, or the motherboard.

    Jordan Troxel - Antwort

  20. 从主板上小心向上撬动并拔下三线插头。 从主板上小心向上撬动并拔下三线插头。
    • 从主板上小心向上撬动并拔下三线插头。

    What can i do if i broke these three little prongs?

    Josh Turner - Antwort

    2 options 1 make a new contact, 2 buy a New fan as it is The fan contact ;)

    Karl eriksson -

    Which kind of connector is this?

    robbitara - Antwort

    Hab meine Halterung auch Abgebrochen.

    Das Komplette “ding” ist vom Mainboard/PCB Abgebrochen…

    Was kann man tun?

    Cem Ce - Antwort

    I accidentally pulled the little red cord out from the white casings. Can I shove it back or do I need a new fan?

    Hobocop - Antwort

    Place one side of tweezers under from wire side, pinch with tweezers, and use to lift up, this pulls the wire out of the lock. (They aren't pins inside, but fins.)

    Linus Porter - Antwort

    Having no patience I pulled all 3 fan wires out of connector on motherboard but all wires have there metal connector tips so can I put back into motherboard or did i ruin my fan

    asmar wash - Antwort

    Please be EXTREMELY careful, as it is exceedingly easy to break that connector. ☹️

    Except, of course, if you actually plan to replace the fan anyway, well, a new connector comes with the fan, so just look out for the motherboard part of it.

    Wolfgang Bachmann - Antwort

  21. 抬起并卸下主板。
    • 抬起并卸下主板。

    • 卸下主板需要分离处理器及散热片之间原厂的散热胶。在你重新组装你的设备时,需要重装一层新的散热胶。参考本指南以了解更多。

    Unfortunately it costs more for the motherboard and optical drive together than it costs for a new PS4 1TB with a game

    Blake Hannan - Antwort

  22. 卸下三颗5mm Phillips head #1螺丝。
    • 卸下三颗5mm Phillips head #1螺丝。

    • 向上垂直抬起金属架以将其移除。

  23. 现在就露出风扇了,卸下两个Phillips head #1螺丝。 如果你的设备在右上角还有一颗螺丝,也要将其卸下。
    • 现在就露出风扇了,卸下两个Phillips head #1螺丝。

    • 如果你的设备在右上角还有一颗螺丝,也要将其卸下。

    • 向上抬起风扇以将其卸下。

    The guide here is wrong, the left screw holding the fan down is also the bottom-most screw holding the step 22 metal cover down. The only screws that should be on the fan at Step 23 should be the lower right screw and upper right screw

    Haybale100 - Antwort

    Yep, I found the same thing.

    anonymous 1428 -

    Me to. but everything else is good

    Adel Mahdi -

    Finally got all the way down to this mother effer! :D

    Mike Harrell - Antwort

Abschluss

参照下列步骤的相反顺序重新安装你的设备。

146 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Z.Heng hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Robert Harvey

Mitglied seit: 01.04.2014

7.842 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team 8-12, Regan Spring 2014 Mitglied von Cal Poly, Team 8-12, Regan Spring 2014

CPSU-REGAN-S14S8G12

5 Mitglieder

32 Anleitungen geschrieben

Great guide, but where to buy a fan for the ps4?!

frankeinarhaugen - Antwort

Look one ebay, that's where my store gets the majority of out parts from. considering we fix computers.

jonathon saygidia -

Will this guide work with the CUH-1200 model?

Jose Alvizo - Antwort

excellent camarade !

Beaux travail !

Attention au principe de peter... Niveaux d'incom.......

je déconne !

P.S. Ne pas se ronger les ongles ca evite les pinces a épiler !

je déconne pas !

Inversement ce pas très esthétique...

Change rien !

Dall - Antwort

My PS4 has been overheating so I decided to take it apart and clean it. I cleaned it well but it still over heats the fan will try to start up but cuts back off plz help

Tristen hudson - Antwort

Replace the fan ... Yours works intermittently that probably means ut has a bad bearing.

chrisforfacebook1987 -

Does the Model work for the CUH-1116A ????

ITS HD - Antwort

Does the fan recommended work for the Model CUH-1116A if not do you know where you can recommend me to get one that's compatiable for it thank you.

ITS HD - Antwort

Well, after replacing the fan, triple checking every thing and plugging it back in…. I got nothing. No power at all.

took it all apart three times to make sure all cables, connections and touch sensors were making contact. Still nothing.

With the bad fan in it at least still powered on befor this.

Many help appreciated !

TomJ - Antwort

Did you find a solution

tchageman -

Did you find a solution? I’m currently having the same issue!

ketaamarie17 -

This was a great guide! I successfully completed the repair today. Thanks for the comprehensive steps and accompanying photos.

Dylan - Antwort

Thank you very much for this repair instructions. I do have one question. At the top of metal plate of the fan are none of the four (I guess) cooling pads shown on the pictures. With which material can I replace them (thickness?)? Thank you in advance.

Marinho - Antwort

My power button doesn’t work, but the eject works and the console seems to be running fine when I turn it on with my controller. Any ideas on what I did wrong?

Megan - Antwort

I followed the guide with no issues, but when I hooked my ps4 up again and pressed the power button, the console beeped, I got the blue light, but then it turned off. No fan, no screen, nothing.

The power button works, and there is power - otherwise I wouldn’t get a beep.

So I took it apart and reinstalled the old noisy fan. When I put it back together, same result.

Anyone have any ideas what the problem could be?

Derek - Antwort

Nice man. Very very so good your guide.

leo.woiciechoski - Antwort

Did this repair, fan is better but now my PS4 cuh-1116a won’t read any game discs?! It did beforehand but I did notice there is a bracket on the top of my optical drive? Is it in the wrong way? Could a wire being loose cause this and if so which one? Any help is appreciated thanks.

Charis Smith - Antwort

After I replaced the fan and thermal paste and reassembled my ps4, I have NO POWER at all. I have disassembled and reassembled countless times to make sure I didn’t miss something. All wires are correctly placed. Someone please help!

ketaamarie17 - Antwort

https://www.easeus.com/resource/how-to-f...

There is also a risk of frying components with static electricity if your were touching all over the motherboard.

Tom Riddle -

Cleaned out the dust and when I put it back together everything worked perfectly, and the stock fan is now silent.

Tom Riddle - Antwort

my playstation is now booting in Safe Mode… please help!

Joe Aguirre - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 142

Letzte 7 Tage: 629

Letzte 30 Tage: 4,694

Insgesamt: 204,664