Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

In this guide we will be disassembling the whole device to replace the speaker. It is very important to keep track of all the components and screws while following these instructions.

Note: This procedure requires removing and reinstalling the battery, which requires the use of a soldering iron and/or a lot of careful disassembly.

  1. Flip the speaker over onto its back. Flip the speaker over onto its back.
    • Flip the speaker over onto its back.

  2. Gently remove the rubber base from speaker by pulling around the edges. Gently remove the rubber base from speaker by pulling around the edges.
    • Gently remove the rubber base from speaker by pulling around the edges.

  3. Remove the four 6mm T9 Torx bit screws from the corners of the battery. Remove the four 6mm T9 Torx bit screws from the corners of the battery.
    • Remove the four 6mm T9 Torx bit screws from the corners of the battery.

  4. Carefully lift the battery from the side nearest the four gold contact pins, but don't try to fully remove it yet. At this point, the battery remains connected via two wires to the power supply board. Carefully desolder the two wires from the power supply board in order to completely detach the battery.
    • Carefully lift the battery from the side nearest the four gold contact pins, but don't try to fully remove it yet.

    • At this point, the battery remains connected via two wires to the power supply board.

    • Carefully desolder the two wires from the power supply board in order to completely detach the battery.

    • For help with soldering, see the soldering guide.

    • Alternatively, you may remove the battery and power supply board together, without any soldering, but access requires some additional disassembly while carefully leaving the battery connected via the two wires the entire time.

    cuanto tiempo dura la bateria original ?

    Marcelo Lastra - Antwort

    the mini 2 battery is soldered to a smaller board, either u desolder it or buy it with the small board, but with that it is even harder to replace

    user user - Antwort

    Yeah this guide is just like the original Bose Mini which looked like that model had a way to replace the batter easily. I purchased a battery off Amazon thinking it was the same. This is not the same. The Bose Mini II has a battery hard-wired directly to the board. Might be too late but read this guide’s comments first to get the low down. The guide is very misleading. The BOSE SOUNDLINK MINI II **DOES NOT HAVE A REPLACEABLE BATTERY**

    Ian Lucero - Antwort

    DO NOT buy a replacement battery until you understand that the battery is HARD WIRED to the circuit board and is NOT designed to be replaceable. If you are not an electronics specialist, the only option is to send to Bose for battery replacement.

    Even if you are an electronics specialist, finding a replacement battery may not be possible.

    ldthom65 - Antwort

    I am very glad I took the time to review everything and all the comments before I started this procedure on my Soundlink Mini 2.

    I have to say, the author of this procedure is a pathetic jerk for posting this and not distinguishing the between the 1 and 2 versions. It is also highly suspect that there is no clear picture of the top of the unit, which would indicate which version is being used due to the fact that the 2 has no mute button.

    trmsd - Antwort

    It’s disappointing, for sure. But to call the author, who’s been kind enough to post this without getting anything in return, a pathetic jerk is waaay over the top! Come on. If anyone deserves abuse, then it’s Bose for producing a speaker with a battery that’s totally and easily replaceable except they decided to solder it onto the circuit board for some unfathomable reason. Argh!

    B. J. - Antwort

  5. Removing the device  front grille with a metal spudger, starting in one corner and working around the border. The grille is easily bent and deformed.
    • Removing the device front grille with a metal spudger, starting in one corner and working around the border.

    • The grille is easily bent and deformed.

  6. iPhone LCD Display Fix Kits

    Die Budgetoption, abgedeckt durch unsere lebenslange Garantie.

    Kits kaufen

    iPhone LCD Display Fix Kits

    Reduziere die Reparaturkosten, nicht die Qualität.

    Kits kaufen
  7. Remove the rear grille with a metal spudger, starting in one corner and working around the border. The grille is easily bent and deformed. The grille is easily bent and deformed.
    • Remove the rear grille with a metal spudger, starting in one corner and working around the border.

    • The grille is easily bent and deformed.

  8. Remove the eight 9mm T9 screws. Remove the eight 9mm T9 screws.
    • Remove the eight 9mm T9 screws.

  9. Use the metal spudger to release ribbon cable retainer. Detach the ribbon cable from the circuit board by sliding out from board connector.
    • Use the metal spudger to release ribbon cable retainer.

    • Detach the ribbon cable from the circuit board by sliding out from board connector.

  10. Pull the ribbon cable through the rear case wall. Pull the ribbon cable through the rear case wall. Pull the ribbon cable through the rear case wall.
    • Pull the ribbon cable through the rear case wall.

  11. Remove the top circuit board by lifting up. Disconnect the wired pair from board upon removal. There is a non latched connector connecting the top board to side board. Be careful to not damage this connector during the removal process.
    • Remove the top circuit board by lifting up.

    • Disconnect the wired pair from board upon removal.

    • There is a non latched connector connecting the top board to side board. Be careful to not damage this connector during the removal process.

  12. Remove the power supply board by sliding it outward from the device. This is the board that was previously soldered to the battery.
    • Remove the power supply board by sliding it outward from the device.

    • This is the board that was previously soldered to the battery.

    • There is a non latched connector connecting the side board to button board. Be careful to not damage this connector during the removal process.

  13. Remove the eight 9mm T9 Torx screws from the front of the device. Remove the eight 9mm T9 Torx screws from the front of the device.
    • Remove the eight 9mm T9 Torx screws from the front of the device.

  14. Use the metal spudger to remove the front case panel. Use the metal spudger to remove the front case panel. Use the metal spudger to remove the front case panel.
    • Use the metal spudger to remove the front case panel.

  15. Remove the speakers from the case. Remove the speakers from the case.
    • Remove the speakers from the case.

Abschluss

To reassemble your device, follow these instructions in reverse order.

6 weitere Nutzer haben diese Anleitung absolviert.

Tyler Roessler

Mitglied seit: 15.02.2017

699 Reputation

1 Anleitung geschrieben

Team

USF Tampa, Team 5-2, Passmore Spring 2017 Mitglied von USF Tampa, Team 5-2, Passmore Spring 2017

USFT-PASSMORE-S17S5G2

4 Mitglieder

6 Anleitungen geschrieben

Anyone know where to find the speaker for replacement?

Matthew - Antwort

Die Anleitung ist Fehlerhaft! Der Akku ist im SLM2 Festgelötet, in der Anleitung kein Wort davon und auch die Bilder sind damit Falsch.

Robert - Antwort

(englisch version below)

Scheinbar eine Verwirrung, es gibt verschiedene Ausführungen des selben Models. Es scheint als sie im amerikanischen die Soundlink mini 2 mit steckbaren Akku verkauft worden und die gelötete in Europa.

It seems there is some confusion ongoing, there are different versions of the same model. It seems likely in Amerika the Soundlink mini 2s battery is unplugable, as the european version is soldered.

Raphael Krug -

Nachtrag! Das ist die Anleitung vom Mini 1 und somit Falsch Deklariert.

Robert - Antwort

The German guy (Robert) seems incorrect. He claims this teardown is for the original Bose MiniSoundlink I. I just confirmed it is indeed a teardown for Bose Mini Soundlink II by checking the model number of my own Soundlink II with the teardown photos showing the model number (in steps 3 & 4). Both show model number 088796., confirming this is Soundlink II.

Jason - Antwort

Hi all.

One of the speakers of my soundlink mini II is malfunctioning (rattling/buzzing) due to (let us say) vandalism. Is there any place where I could purchase the replacement for the speaker?. I am in Spain and I can not find it. Thanks !

porrinchas - Antwort

How do you repair the press button on and off it has warned out. No longer cutting on or off due to the rubber switch wear and tear

Bernadette Everette - Antwort

Anyone know where can I get a shell and grill replacement part for my soundlink mini 2? I want to replace the shell and the grill of my soundlink mini 2.

Hadrian Wong - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 28

Letzten 7 Tage: 171

Letzten 30 Tage: 629

Insgesamt: 12,728