Zum Hauptinhalt wechseln

DualShock 4 (CUH-ZCT1U) Akku tauschen

Was du brauchst

  1. DualShock 4 (CUH-ZCT1U) Akku tauschen, Modell überprüfen: Schritt 1, Bild 1 von 1
    • Überprüfe die Modellnummer auf der Rückseite des Controllers. Die Anleitung wurde mit einem CUH-ZCT1U Modell geschrieben. Wenn du ein anderes Modell hast, können sich die Verfahren und die Teile leicht unterscheiden.

    • Wenn du ein Modell der zweiten Generation eines DualShock 4 hast, mit der Modellnummer CUH-ZCT2U, benutze diese Anleitungen.

    model:cuh-zct2e

    كيف يمكن ان افكها

    Mhmod - Antwort

  2. DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückabdeckung losschrauben: Schritt 2, Bild 1 von 2 DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückabdeckung losschrauben: Schritt 2, Bild 2 von 2
    In diesem Schritt verwendetes Werkzeug:
    Microfiber Cleaning Cloths
    $3.99
    • Um den Kontroller während der Reparatur sicher zu lagern, kannst du eine weiche Unterlage, z.B. ein Mikrofasertuch verwenden.

    • Entferne die vier 6,4 mm langen Kreuzschlitzschrauben, mit denen die Rückabdeckung befestigt ist.

    to re-torque these PH00 screw... i found 19Ncm to be about the max. (since 27Ncm was too much)

    Dreamcat 4 - Antwort

  3. DualShock 4 (CUH-ZCT1U) Akku tauschen, L1-Taste entfernen: Schritt 3, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, L1-Taste entfernen: Schritt 3, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, L1-Taste entfernen: Schritt 3, Bild 3 von 3
    • Heble mit einem Plektrum an jeder Ecke der L1-Taste, bis sie sich vom Gehäuse löst.

    • Decke die Taste ab, damit sie nicht davonfliegen kann.

    • Entferne die Taste.

  4. DualShock 4 (CUH-ZCT1U) Akku tauschen, R1-Taste entfernen: Schritt 4, Bild 1 von 1
    • Entferne in gleicher Weise die R1-Taste.

    I didn't have to remove the buttons just to replace the battery ...

    Justin Vander Ziel - Antwort

  5. DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückgehäuse lösen: Schritt 5, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückgehäuse lösen: Schritt 5, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückgehäuse lösen: Schritt 5, Bild 3 von 3
    • Das Rückgehäuse ist mit sechs Rasten am vorderen Gehäuseteil befestigt. In den nächsten vier Schritten wird gezeigt, wie die Rasten gelöst werden, bevor das Gehäuse geöffnet werden kann.

    • Setze das Plektrum nach unten geneigt in der Mitte zwischen Griff und Aktionstasten zwischen Vorder- und Rückseite ein.

    • Schiebe das Plektrum zum Griff hin und heble gleichzeitig, bis sich die erste Raste löst.

    • Wiederhole das Ganze auf der anderen Seite des Controllers, um die zweite Raste zu lösen.

  6. DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 6, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 6, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 6, Bild 3 von 3
    • Zwei weitere Rasten halten die Gehäuseteile beim Erweiterungsabschluss und der Kopfhörerbuchse zusammen.

    • Setze das Plektrum links und rechts von den Anschlüssen zwischen dem vorderen und rückseitigem Gehäuseteilen ein.

    • Verdrehe das Plektrum, bis sich die Gehäuseteile voneinander lösen.

    • Wenn sich die Teile nicht leicht lösen, dann setze das Plektrum in verschiedenen Winkeln ein.

    • Öffne den Controller noch nicht, er wird immer noch mit zwei sehr empfindlichen Rasten in der Nähe der Trigger-Tasten zusammengehalten.

  7. DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 7, Bild 1 von 1
    • Die letzten beiden Rasten sind sehr empfindlich und müssen von innen aus dem Gehäuse geöffnet werden. Wenn sie dabei brechen, ist es nicht so schlimm, die Reparatur und die Funktion wird dadurch nicht beeinträchtigt.

    • Du findest die Rasten, wenn du durch den Spalt über den R2- und L2-Tasten schaust.

    Ah, well perhaps I may have broken a tab by not removing the buttons but if be more worried about breaking the buttons

    Justin Vander Ziel - Antwort

  8. DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 8, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 8, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 8, Bild 3 von 3
    • Schiebe die Spitze eines Spudgers durch den Spalt über der R2-Taste und drücke die Raste nach außen.

    • Während du die Raste nach außen drückst, ziehe gleichzeitig das Rückgehäuse langsam vom vorderen Gehäuseteil ab, bis sie sich voneinander lösen.

    • Öffne den Controller erst, wenn beide Rasten bei R2 und L2 gelöst sind.

    • Wiederhole das Verfahren für die Raste bei der L2-Taste.

  9. DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückseite entfernen: Schritt 9, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückseite entfernen: Schritt 9, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, Rückseite entfernen: Schritt 9, Bild 3 von 3
    • Drücke die R2-Taste und schiebe die Gehäuserückseite darüber.

  10. DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 10, Bild 1 von 1
    • Drücke die L2-Taste und schiebe die Gehäuserückseite darüber.

  11. DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 11, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 11, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen: Schritt 11, Bild 3 von 3
    • Klappe die Gehäuserückseite oben über den Controller und lege sie ab, achte dabei darauf, dass das Verbindungskabel nicht zu stark angespannt wird.

  12. DualShock 4 (CUH-ZCT1U) Akku tauschen, Verbindungskabel abtrennen: Schritt 12, Bild 1 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, Verbindungskabel abtrennen: Schritt 12, Bild 2 von 3 DualShock 4 (CUH-ZCT1U) Akku tauschen, Verbindungskabel abtrennen: Schritt 12, Bild 3 von 3
    In diesem Schritt verwendetes Werkzeug:
    Tweezers
    $4.99
    • Ziehe das Verbindungskabel mit einer Pinzette oder deinen Fingern an der blauen Zuglasche aus seinem Anschluss heraus.

    • Achte beim Zusammenbau darauf, dass die Zuglasche beim Verbinden des Steckers zur Außenseite hin zeigt.

    On the model CUH-ZCT2E the circuit board is mirrored so that the connection is on the left side. When reassembling the blue tab should be facing inwards.

    Konrad Skeri Ekblad - Antwort

    I just left the interconnect cable attached and held things out of the way when I put in the new battery

    Justin Vander Ziel - Antwort

  13. DualShock 4 (CUH-ZCT1U) Akku tauschen, Akku abtrennen: Schritt 13, Bild 1 von 2 DualShock 4 (CUH-ZCT1U) Akku tauschen, Akku abtrennen: Schritt 13, Bild 2 von 2
    • Fasse den Stecker des Akkukabels mit einer Pinzette oder deinen Fingern und trenne ihn von der Hauptplatine ab.

    • Ziehe nur am Stecker, nicht am Kabel.

  14. DualShock 4 (CUH-ZCT1U) Akku tauschen, Akku entfernen: Schritt 14, Bild 1 von 1
    • Entferne den Akku.

Abschluss

Um dein Gerät wieder zusammenzubauen, folge den Schritten in umgekehrter Reihenfolge.

Entsorge deinen Elektromüll fachgerecht.

Hat die Reparatur nicht ganz geklappt? Versuche es mit ein paar grundständigen Lösungen, ansonsten findest du in unserem Forum Hilfe bei der Fehlersuche.

212 weitere Personen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Clay Eickemeyer

Mitglied seit: 09/19/22

81.013 Reputation

455 Anleitungen geschrieben

Team

Guide Team Mitglied von Guide Team

Staff

9 Mitglieder

11.335 Anleitungen geschrieben

31 Kommentare

My Dualshock 4 wont turn on after the battery replacement.

Any idea on why this happened?

Alexander - Antwort

have you tried to charge it?

Mohamed Aden -

I had a problem with my console but with your guide it is possible to solve this one I think.

Praska - Antwort

I found a replacement battery here, you have to mod the tray a little, but it works like a champ and doubles the life.

http://www.ebay.com/itm/PS4-Controller-B...

binazriel - Antwort

The x button on my controller want working properly so I ordered new rubber mounts. I followed the guide, taking my time to make sure I didn't damage anything.

With the new rubber in place I put everything back together and the controller was working fine but now I've realised it doesn't charge. The battery goes completely dead and switches off. If I then connect it with usb cable it doesn't charge but will turn on the controller for maybe 10 seconds before switching off again.

Anyone any idea what is going on? Thanks.

Kenny - Antwort

i have the exact same problem did you fix it?

dasda -

my controller is not starting today

Harry Patidar - Antwort

Did this fix to the letter, controller works now but the light bar does not and I'm unsure if it charges. It shows it's fully charged. Could it be that the micro-usb connection is frapped?

the00brotherhood - Antwort

Ok, so it shows it’s fully charged on the PS4 but the light on the controller is out if I’m reading you right. Method I would use… connect the controller to your computer with a wired cable (eliminating the PS4 from the equation).

Check Device Manager in Windows or System Report on a Mac. Does it show your controller?

Yes = USB port on controller is fine, you may have damaged the LED on it during the repair.

No = USB port may be damaged or the cable may be fried.

Your problem doesn’t seem like it would have anything to do with the USB port. If it works but with no lighting, you should be ok unless you use the controller with the PS4 camera.

Brad S -

The battery outlet got ripped off. Can it still be fixed?

nextinline3900 - Antwort

Anything can be fixed. But without knowing how severe the damage is it’s hard to say how difficult it would be, although it may involve cannibalizing another controller. At this point it may be cheaper to just purchase a new Dual Shock.

Brad S -

Hi I have two PS 4 controller that wont charged. I had checked with all the possibilities before purchasing two new 2000 Mah replacement batterries. But after replacing the old batteries, I noticed that one of them stopped charging. I thought it had reached the capacity to the full, but to my surprise it did not work, the light is just blinking when I turned it on. I reset the unit but remmained the same !!!

Could it be the charging port got damaged ??? Kindly advice

my other controller is still charging and I have not tested it.

Wushangkehan - Antwort

By the way, I plugged into the computer…the device manager did not read the presence of the PS 4 controller , could it be the USB port is damaged ???Kindly advice

Wushangkehan - Antwort

I have a simple question…..I replaced my sons PS4 battery with a replacement battery and charging cable……I plugged it all back in as shown…..Now the controller is working……But the battery level on the console/tv is showing it’s charging…..But it does work…….Any idea or reason why the new battery or controller is showing charging still without being connected to the usb? Ty

myfam73 - Antwort

Be carefull with 2000mah batteries. I’m talking about V2 Dualshock 4. The original battery : 54mm x 35mm x 8,5 mm and 24g with the hardcase. In this space, you can’t have a 2000mah. Check the size of a true 2000mah 3,7v cell, and you will see a really bigger size. So, these replacement batteries with the same look as the original one, are fake ! If they work, because many are dead and don’t work at all, you will never have 2000mah. I found a true new 3,7v li-ion cell on Ebay, that fits perfectly, but it’s a 1500mah, and without a hardcase. I had to weld the original connector, but it fits perfectly. Not any voltage problem. So, if you need a new battery, don’t bought any hardcase version, and check the dimensions and weight.

KOULLIT - Antwort

The blue plastic thingy goes away from the battery. There are letters (maybe symbols) on the ribbon opposite of the blue plastic thingy and they are pointing toward the battery

Ryan A - Antwort

so what happens if your controller requires a smaller insert (that is circular and not a square input [which is provided standard in the 2k mah? Same module number but different connectors?

mhoffmanmobile - Antwort

I know this question is from a few years ago but I'll answer here from my experience: after comparing the model LIP1522 and that the voltage, mAh and Wh were the same I cut the connector with some extra wire off my original battery that worked and attached (soldered) then to the wires of the new battery after cutting off the wrong size connector. My controller works

Justin Vander Ziel -

I had trouble with analoge, I fixed that but FPC (flat connector) on mainboard broken and I soldered new 12 pin FPC on mainboard again, but in reverse!

then I put charging cable and the dualshock did not turn on , and I sensed that the dualshock is heating up, I remove charging cable as soon as possible.

problem is this : negative and positive putted in reverse.

I don’t kwow what happen if I solder new FPC in right position .

Does it work or somethings going to out of service?

sorry formy poor English language .

regards,

Hamed

hamed1379 - Antwort

i struggled with the reassembly; its much easier if you attach the L2 and R2 buttons to the upper half of the controller.

follow these steps:

reattach first the battery, then the cable with the blue pull tab.

then assemble the L2 and R2 buttons as follows: make sure to position the springs in their appropriate slots (especially at the hinge receptecle at the upper shell, align the spring and hinges and push it into the holder.

only then assemble the two body halfes together by first guiding the L1&2 and R1&2 buttons in their correct location. finally slightly bend the long studs into the handle grips and tighten all 4 screws.

wooghee - Antwort

I can’t get the battery connector cable out of the socket. I tried to remove it for 15 minutes and it wouldn’t come out.

marcus2159 - Antwort

After replacing the battery, the controller can only be used while charging with the cable.

What is the cause of this?

RK-pkmn - Antwort

My dualshock 4 is charging but isn't turning on

Derrick Egwalusor - Antwort

How can I check which model/version is my controller? (I dont have the back sticker , it fell out a while ago)

Ariel Peteri - Antwort

Hi! From looking at the V2 guides, I found a couple distinguishing factors in each controller. The body design near the vibration motors, the shape and color of the motherboard, and the shape of the plastic around the triggers are all key features to compare between models. Use photos from our disassembly guides for each model, and compare the parts of your controller to parts sold on this site or elsewhere to identify your model.

Clay Eickemeyer -

As of March 14, 2023, this guide has been updated! Comments regarding step procedures may no longer be relevant.

Clay Eickemeyer - Antwort

Will this guide work with the cuh-zct1e PS4 controller model?

Nick Cellini - Antwort

It's likely to be physically the same. There may be a minor component missing or added between variations of these controllers. But, for a battery replacement, it will be at least close to the same opening process.

Clay Eickemeyer -

Thanks Clay! I'll give it a go and coment here if I come across any devastating differences or difficulties!

Nick Cellini -

Sure thing, I'll watch my notifications. When you do open it up, be mindful of the small shoulder clips. Everything else can be experimented on, without too much risk of breaking clips.

Clay Eickemeyer -

SWo when I pluggeged un the battery you I bought from you I bnlew up my controlner and it smelt fvery bad

gooka booka - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 91

Letzte 7 Tage: 687

Letzte 30 Tage: 2,733

Insgesamt: 409,428