Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

Follow this guide to remove the rear-facing cameras from your Moto X4.

  1. Before you begin, turn off your phone. Heat an iOpener and apply it to the left edge of the phone for two minutes.
    • Before you begin, turn off your phone.

    • Heat an iOpener and apply it to the left edge of the phone for two minutes.

    • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

    • As you wait, take note of the the following areas:

    • Display cable—be careful not to slice too deeply near the edge here, or you may damage the display cable.

    • Fingerprint sensor cable—be careful not to slice too deeply near the edge here, or you may damage the fingerprint sensor cable.

  2. Apply a suction cup to the screen, as close to the heated edge as possible. Pull on the suction cup with strong, steady force to create a gap in the seam. Insert the point of an opening pick into the gap.
    • Apply a suction cup to the screen, as close to the heated edge as possible.

    • Pull on the suction cup with strong, steady force to create a gap in the seam.

    • Insert the point of an opening pick into the gap.

    • Depending on the age of your phone, this may be difficult. If you are having trouble, apply heat to the edge and try again.

  3. Slide the opening pick along the edge to slice through the adhesive. Leave an opening pick in the seam to prevent the adhesive from re-sealing. Leave an opening pick in the seam to prevent the adhesive from re-sealing.
    • Slide the opening pick along the edge to slice through the adhesive.

    • Leave an opening pick in the seam to prevent the adhesive from re-sealing.

  4. Heat the top edge of the phone with an iOpener. Carefully slice around the corner and through the top edge to separate the adhesive. Carefully slice around the corner and through the top edge to separate the adhesive.
    • Heat the top edge of the phone with an iOpener.

    • Carefully slice around the corner and through the top edge to separate the adhesive.

  5. Heat the screen's right edge with an iOpener. Be careful not to slice too deeply near the cables to avoid damaging them. Use an opening pick to slice along the right edge to separate the adhesive.
    • Heat the screen's right edge with an iOpener.

    • Be careful not to slice too deeply near the cables to avoid damaging them.

    • Use an opening pick to slice along the right edge to separate the adhesive.

  6. Repeat the previous steps to heat and slice the bottom edge of the phone. Repeat the previous steps to heat and slice the bottom edge of the phone.
    • Repeat the previous steps to heat and slice the bottom edge of the phone.

  7. Do not try to remove the screen yet—it is still attached to the phone by delicate flex cables. Carefully lift up the left edge of the screen and cut away remaining adhesives with an opening pick.
    • Do not try to remove the screen yet—it is still attached to the phone by delicate flex cables.

    • Carefully lift up the left edge of the screen and cut away remaining adhesives with an opening pick.

  8. Swing open the screen and prop it up with a small box as you work on disconnecting the flex cables.
    • Swing open the screen and prop it up with a small box as you work on disconnecting the flex cables.

    • During reassembly, this is a good time to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

  9. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  10. Slide the point of a spudger underneath the fingerprint sensor cable and gently pry up to loosen the cable from the phone. Do not pull on the cable. It is still attached to the phone by a delicate ZIF socket.
    • Slide the point of a spudger underneath the fingerprint sensor cable and gently pry up to loosen the cable from the phone.

    • Do not pull on the cable. It is still attached to the phone by a delicate ZIF socket.

  11. Use the point of a spudger to flip up the lock bar on the fingerprint sensor's ZIF socket, near the bottom right of the phone. Use tweezers to carefully slide the fingerprint sensor cable out of the socket. Use tweezers to carefully slide the fingerprint sensor cable out of the socket.
    • Use the point of a spudger to flip up the lock bar on the fingerprint sensor's ZIF socket, near the bottom right of the phone.

    • Use tweezers to carefully slide the fingerprint sensor cable out of the socket.

  12. Use an opening tool to flip up the wide lock bar on the display cable's ZIF socket, near the top right of the phone. Use tweezers to carefully slide the display cable out of the ZIF socket. Use tweezers to carefully slide the display cable out of the ZIF socket.
    • Use an opening tool to flip up the wide lock bar on the display cable's ZIF socket, near the top right of the phone.

    • Use tweezers to carefully slide the display cable out of the ZIF socket.

  13. Remove the screen. During reassembly, follow this guide to install custom-cut adhesives for your phone.
    • Remove the screen.

    • During reassembly, follow this guide to install custom-cut adhesives for your phone.

  14. Remove the following twenty screws securing the midframe: Eleven silver 2.7 mm-long T3 screws
    • Remove the following twenty screws securing the midframe:

    • Eleven silver 2.7 mm-long T3 screws

    • Nine black 3.6 mm-long T4 screws

    • The midframe is still held in place by clips.

  15. The next few steps show how to loosen the midframe clips. Insert the flat end of a spudger under the right edge of the metal midframe and pry up to loosen the midframe. Insert an opening pick in the edge to hold the midframe in place.
    • The next few steps show how to loosen the midframe clips.

    • Insert the flat end of a spudger under the right edge of the metal midframe and pry up to loosen the midframe.

    • Insert an opening pick in the edge to hold the midframe in place.

  16. Insert the flat end of a spudger under the lower right edge of the midframe and pry up to release the midframe clip. Insert the flat end of a spudger under the lower right edge of the midframe and pry up to release the midframe clip.
    • Insert the flat end of a spudger under the lower right edge of the midframe and pry up to release the midframe clip.

  17. Grasp the lower edge of the midframe and pull the edge slightly to the right, to clear the metal midframe clip. Grasp the lower edge of the midframe and pull the edge slightly to the right, to clear the metal midframe clip. Grasp the lower edge of the midframe and pull the edge slightly to the right, to clear the metal midframe clip.
    • Grasp the lower edge of the midframe and pull the edge slightly to the right, to clear the metal midframe clip.

  18. Insert the point of an opening pick under the top left corner of the midframe and twist slightly to release the top clip. Insert the point of an opening pick under the top left corner of the midframe and twist slightly to release the top clip.
    • Insert the point of an opening pick under the top left corner of the midframe and twist slightly to release the top clip.

  19. Remove the midframe. To reinstall the midframe: Align the the midframe's top edge to the phone and press it into position.
    • Remove the midframe.

    • To reinstall the midframe:

    • Align the the midframe's top edge to the phone and press it into position.

    • Shift the bottom edge slightly to the left, to maneuver the left metal midframe clip underneath the phone edge.

    • Press the midframe's bottom edge into position.

  20. Insert the point of a spudger underneath the top edge of the battery connector. Be careful not to dislodge the small surface-mounted components surrounding the socket.
    • Insert the point of a spudger underneath the top edge of the battery connector.

    • Be careful not to dislodge the small surface-mounted components surrounding the socket.

    • Gently pry up the connector to disconnect the battery.

  21. To re-connect the battery, align the connector on top of the socket, and press   it down with your finger or a spudger. To re-connect the battery, align the connector on top of the socket, and press   it down with your finger or a spudger. To re-connect the battery, align the connector on top of the socket, and press   it down with your finger or a spudger.
    • To re-connect the battery, align the connector on top of the socket, and press it down with your finger or a spudger.

  22. Using a T3 Torx screwdriver,  remove both  1cm  screws. To do this, insert the screwdriver into the head of the screw, then turn counter-clockwise. Using a T3 Torx screwdriver,  remove both  1cm  screws. To do this, insert the screwdriver into the head of the screw, then turn counter-clockwise.
    • Using a T3 Torx screwdriver, remove both 1cm screws. To do this, insert the screwdriver into the head of the screw, then turn counter-clockwise.

  23. Use the tweezers to gently lift the rear camera  up and out of your Moto X4. Use the tweezers to gently lift the rear camera  up and out of your Moto X4.
    • Use the tweezers to gently lift the rear camera up and out of your Moto X4.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Motorola Moto X4 Answers community for help.

3 weitere Nutzer haben diese Anleitung absolviert.

Brian Buchanan

Mitglied seit: 24.01.2018

954 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team S18-G4, Livingston Winter 2018 Mitglied von Cal Poly, Team S18-G4, Livingston Winter 2018

CPSU-LIVINGSTON-W18S18G4

4 Mitglieder

10 Anleitungen geschrieben

I'm up based anyone know where I can get a replacement camera

Ashley Fall - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 4

Letzten 7 Tage: 10

Letzten 30 Tage: 61

Insgesamt: 2,200