Einleitung
Diese Anleitung zeigt dir, wie du den Akku im OnePlus 3 entfernen kannst. Der schwierigste Teil ist das Öffnen der Rasten am Rahmen.
Wenn der Akku aufgebläht ist, musst du entsprechende Vorsichtsmaßnahmen treffen.
Entlade aus Sicherheitsgründen den Akku auf unter 25% bevor du dein Smartphone öffnest. Dadurch wird das Risiko eines Brandes reduziert, falls du den Akku bei der Reparatur versehentlich beschädigen solltest.
Hinweis: Achte darauf, dass dein Akku passend zu deinem Modell ist, bevor du die Reparatur beginnst. OnePlus 3 (BLP613) und OnePlus 3T (BLP633) sind verschieden und nicht austauschbar.
Was du brauchst
-
-
Nimm ein SIM-Auswurfwerkzug, ein Bit oder eine aufgebogene Büroklammer und setze es in das kleine Loch zwischen An/Aus-Knopf und SIM-Slot.
-
Drücke es kräftig hinein, um den SIM-Einschub aus dem Gerät zu lösen.
-
-
-
Entferne die beiden 2,6 mm Torx T2 Schrauben an der Unterkante des Smartphones.
-
-
-
Naht am Displayglas. Diese Naht gehört zur Displayeinheit. Heble nicht an dieser Naht, sonst trennst du die Bildschirmeinheit auf und beschädigst sie.
-
Naht am Rahmen. Hier sind der Kunstoffrahmen und die Rückabdeckung miteinander verbunden. Heble nur an dieser Naht.
-
Der Rahmen ist mit vierzehn Rasten an der Rückabdeckung befestigt. Beim Abhebeln der Rückabdeckung musst du genau wissen, wo sie sich befinden.
This picture is a bit misleading, the frame seam is actually sunk into the metal frame, and is not visible at first.
With an older phone, it’s more likely to separate the display panel itself than to separate the displaypanel from the frame. If the top of the screen comes off first, before the part with the touch sensor, then you’re separating the wrong thing (ie displaypanel).
Mind that the displaypanel itself seems as if it has two seams (the panel itself and the board).
Thanks for the helpful tip! I re-worded the step slightly to hopefully clarify where the frame seam is.
-
-
-
Bringe einen Saugheber nahe der Unterkante des Displays an.
-
Ziehe gleichmäßig und kräftig am Saugheber.
-
Drücke die Kante eines Plastiköffnungswerkzeugs direkt in die Rahmenaht nahe beim Saugheber, bis sich die Kante des Werkzeugs zwischen Kunstoffrahmen und dem Rand der Rückabdeckung einzwängt.
To get maximum leverage and make this step possible with my weaker suction cup, I held down the phone with a plastic pick/tool pressed down onto the metal back. As the suction cup pulled up the plastic frame, the plastic pick holding down the metal back naturally was pushed further and further into the gap between the frame and back.
-
-
-
Wenn das Plastiköffnungswerkzeug eingezwängt ist, dann kannst du es sorgfältig an der Unterkante des Smartphones entlang schieben.
-
Führe das Werkzeug vorsichtig um die linke Ecke des Smartphones herum, halte es dabei immer in der Naht drin.
-
-
-
Schiebe das Plastiköffnungswerkzeug weiter die lange Kante entlang, wobei sich die Rasten lösen.
I couldn’t get the last clip easily, so I also went around the other side, and then the last two clips left and right went out togther much more easily.
Yep, thanks for your note. It was far more easy to go round the other side.
-
-
-
-
Wenn die untere und die linke Kante des Smartphones frei sind, kannst du vorsichtig am Rahmen wackeln, damit sich auch die Rasten an der oberen und der rechten Kante lösen.
-
Hebe den Bildschirm hoch und entferne ihn.
-
Richte die Oberkante des Rahmens an der Rückabdeckung aus und achte darauf, dass die oberen Rasten korrekt sitzen.
-
Drücke an den langen Kanten des Smartphones entlang, so dass die restlichen Rasten einschnappen.
I’m having trouble putting on the back cover, anyone else had this issue?
Hello.
From this Step on I directly jumped to Step 13. Removing the 7 Screws. NOT removing the Mainboard. It is easy possible to remove the camera just like this if you loosen the Camera-cable and pull carefull on it. Because the 7 Screws are removed there is enough space to remove the old camera and bring the new camera in. I tried It various times to verify this.
-
-
-
Heble mit der Spudgerspitze den Akkustecker aus seinem Anschluss über der rechten oberen Ecke des Akkupacks hoch und trenne ihn ab.
-
Biege den Stecker vom Anschluss weg, so dass er sich nicht versehentlich verbinden kann.
Why not removing the camera without removing the mainboard?
Warum wird die rückseitige Kamera nicht ausgebaut, ohne das Mainboard auszubauen?
Hello Ingo,
The rear camera is trapped under the motherboard. You must at least loosen the motherboard to remove the camera.
Die Kamera befindet sich unter dem Motherboard. Sie müssen mindestens das Motherboard lösen, um die Kamera zu entfernen.
During reassembly this part was tricky for me: the new battery couldn’t clip into place the way the old one did, resulting in a loose connection and “battery does not match “ message when trying to power the phone up. The new battery probably had a slightly different connector that than the old one. I even ordered another battery but the same thing happened. I finally managed to connect it by applying much more pressure on the press connector than needed for the other ones. it did not make any clip sound though.
-
-
-
Entferne die 3 mm Kreuzschlitzschraube, mit der die Kabelhalterung befestigt ist.
-
Entferne die Kabelhalterung.
-
-
-
Heble das Verbindungsflachbandkabel mit der Spudgerspitze hoch und löse es oberhalb des Akkus von der Hauptplatine ab.
-
Trenne genauso das Flachbandkabel zur Tochterplatine von der Hauptplatine ab.
-
-
-
Unter dem Akku befindet sich das Verbindungsflachbandkabel zur Tochterplatine. Heble es mit der Spudgerspitze hoch und trenne es ab.
-
-
-
Entferne das Verbindungsflachbandkabel.
-
Biege das immer noch verbundene Kabel vorsichtig vom Akku weg.
Upon reassembly place the cable back correctly. Apparently, it is often overlooked, see: Replaced Battery, Now My Phone is Overheating and Won't Boot
Thanks for the tip! I’ll adjust the step add this info.
-
-
-
Schiebe mit dem Plastiköffnungswerkzeug alle Stücke von Klebeband ab, mit denen der Akku an der Kante des Kunstoffrahmens befestigt ist. Auf jeder Seite des Akkus sollte sich mindestens ein Klebestreifen befinden.
-
-
-
Halte den Rahmen des Smartphones fest gegen den Tisch.
-
Ziehe die durchsichtige Zuglasche fest und gleichmäßig nach oben, bis sich der Akku aus seiner Vertiefung löst.
-
Klappe den Akku ganz aus seiner Vertiefung heraus und ziehe alle Kleberreste ab.
I found (once I had bent the old battery removing it) that there is a film around the battery which would come away much more easily. I suggest this step is updated:
Peel back the four black sticky tabs which say “Position 1” (one at each corner of the battery) and the peel back the black sticky film connected to the tabs. Now pull the clear pull tab upwards and the battery should come away.
This! I did it by unpealing the “Position 1” tabs, and then pulled the battery much more easily. Thanks for the hint! Interestingly, it still came out with the black film intact and on the battery. I then put this black film and the pull tab on the new battery, which didn’t have either. I applied some double-sided tape between the black film and the phone to glue the whole thing in place.
I agreee , just peel the “position1” tabs. Plus my spare battery didn’t come with these tabs so I had to reuse the old ones anyway.
romDL -
-
-
In diesem Schritt verwendetes Werkzeug:Tesa 61395 Tape$5.99
-
Entferne den Akku und beseitige alle Kleberreste vom Rahmen.
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Für eine optimale Leistung, solltest du deinen neu eingebauten Akku kalibrieren: Lade ihn auf 100% auf und lasse ihn mindestens zwei weitere Stunden am Ladegerät. Benutze ihn dann, bis sich das Smartphone aufgrund eines leeren Akkus von selbst ausschaltet. Lade ihn dann zum Abschluss ununterbrochen auf 100% auf.
Entsorge deinen Elektroabfall fachgerecht.
War die Reparatur doch nicht erfolgreich? Auf unserem OnePlus 3 Antwortenforum kannst du Hilfe finden.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Für eine optimale Leistung, solltest du deinen neu eingebauten Akku kalibrieren: Lade ihn auf 100% auf und lasse ihn mindestens zwei weitere Stunden am Ladegerät. Benutze ihn dann, bis sich das Smartphone aufgrund eines leeren Akkus von selbst ausschaltet. Lade ihn dann zum Abschluss ununterbrochen auf 100% auf.
Entsorge deinen Elektroabfall fachgerecht.
War die Reparatur doch nicht erfolgreich? Auf unserem OnePlus 3 Antwortenforum kannst du Hilfe finden.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
55 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
13 Kommentare
Is this tutorial and the repair kit also applicable for the OnePlus 3T model? Thanks in advance for helping!
The tutorial for the 3T model would be similar, but not completely identical to this guide. Since the battery capacity is different between the 3 and 3T, the repair kit would not be applicable. However, the tools are most likely the same.
Thanks for your response Arthur! Is it planned to offer a battery kit also for the OnePlus 3T? I’d definitely appreciate it since I can’t find any trustworthy OnePlus 3T batteries so far. Best regards!
Unfortunately, I don’t think we are releasing a 3T battery kit anytime soon.
My One Plus 3 is A3003, is the BLP613 battery compatible with this device ? on some website they write that A3003 is One Plus 3T and not One plus 3 …
Hi Alexandre,
OnePlus seemingly used the A3003 model for both the OnePlus 3 and 3T model. You can try opening the “About Phone” page in the settings menu to see what the phone lists itself as.
The OnePlus 3T has a bigger battery (3400 mAh vs. 3000 mAh), so there is a strong chance that the two are incompatible.
Great guide, replacement went smoothly
Replaced my battery recently. It went well. Thanks for the guide!
The need for my own adhesive isn't mentioned anywhere except at the very bottom. I ended up not using any because I don't have any. It'd be nice if it were listed as a "tool" or "part" at the top.
I followed the steps to calibrate the battery, but for several days now, my phone's shutting down due to low battery (like extreeemely low, not the usual "hmmm I'm low on battery I'm gonna turn myself off" but rather instant death). Any tips? I do have LineageOS instead of Hydrogen or Oxygen.
I'm in the same situation. Is the phone ok without the adhesive on the battery?
Vorador -
I've just realized that. I have a 3T and bought from ifixit a battery replacement for a One plus 3. because it was "Global (A3003)" compatible. Which my 3T indicates on the back frame... It is misleading, don't buy this battery.